Star Headlight & Lantern 3930 User Manual

REMOTE STROBE HEAD INSTALLATION

1. IMPORTANT: Please read all of the following instructions before installing your
new remote strobe system.

2. The remote strobe head must be connected to a power pak to operate. You may
use our two-outlet, four-outlet, or six -outlet paks. These heads may or may not
work with alternate brand power paks. The installer accept any and all liability if
this head is used in conjunction with any unapproved power paks.

3. Connect your heads to your power pak using the proper cable: part #3820 for light
duty cable, #3814 for heavy duty cable, or 4415 for shielded cable (used with the
Optimax paks).

4. If you intend to use your own cable, it must meet certain specifications as follows:
It must be three-conductor with 600V insulation, minimum 18 AWG for 0-20 ft., 16
AWG for 21-30 ft. or 14 AWG for 31-50 ft. We do not recommend the use of any
cable length greater than 50 feet, as the resistance might cause a drop in voltage
resulting in inconsistent or complete loss of firin g in the heads.

5. For good, reliable connections between the cable system and the strobe tube head
in various weather and contamination conditions, it is strongly recommended that a
dielectric grease or more specifically Truck-Lite NYK Corrosion Preventative
Compound (2 fl. oz. tubes) be used on the connectors. This compound is
available from Truck-Lite. It should be applied and into each terminal area where
the connectors mate, before joining the two connectors together. We have found
this procedure to be effective even under the most extreme of conditions. Do Not

Seal The Connectors Using Silicon Or RTV.

6. A template is provided on the back of this sheet if you are installing model
#SH3920 oval heads and need to drill a hole.

7. If you must remove the weatherproof connector for any reason, please re-insert the
wires back into their proper location. Please refer to the diagram below. If you
need to order another weatherproof connector kit, please use part #CK703. This kit
contains one connector (30185-4), three male pins (30042-29), and three rubber
seals (30186-2).

30185-4 30042-29

30186-2

RED

BLACK

WHITE

8. If you need to order a weatherproof connector kit to mate with the CK703 (the
connector on your strobe head), please use part #CK702 (not shown). This kit
contains one connector (30185-3), three female pins (30042-30), and three rubber
seals (30186-2).

(HOT)

(GROUND)
(TRIGGER)

R1.25"

OVAL

STROBE

HEAD

TEMPLATE

4.25"

ONE YEAR LIMITED

WARRANTY

The manufacturer warrants each new product, under
normal use, against factory defects in material and
workmanship for one year after the date of purchase.
The owner will be responsible for returning to the
Service Center any defective item(s) with the
transportation costs prepaid. The manufacturer will,
without charge, repair or replace at its option,
products, or part(s), which its ins pection determines
to be defective. Repaired or replacement item(s)
will be returned to the purchaser with transportation
costs prepaid from the service point. A copy of the
purchaser's receipt must be returned with the
defective item(s) in order to qualify for the warranty
coverage.

Exclusions from this warranty include, but are not
limited to, bulbs, strobe tubes, domes, and/or the
finish. This warranty shall not apply to any light,
which has been altered, such that in the
manufacturer's judgment, the performance or
reliability has been affected, or if any damage has
resulted from abnormal use or service. This
warranty does not apply to defect or damage
occurring as a result of disaster, accident, abuse,
misuse, lightning, power surges, or failure to follow
instructions in any enclosed manuals. Any damage
or defects occurring as a result of any unauthorized
service or repairs by unauthorized persons shall be
excluded from this warranty.

There are no warranties expressed or implied
(including any warranty of merchantability or
fitness), which extend this warranty period. The

loss of use of the product, loss of time,
inconvenience, commercial loss or consequential
damages, including costs of any labor, are not
covered. The manufacturer reserves the right to

change the design of the product without assuming
any obligation to modify any product previously
manufactured.

This warranty gives you specific legal rights. You
might also have additional rights which may vary
from state to state. Some states do not allow
limitations on how long an implied warranty lasts.
Some states do not allow the exclusion or limitation
of incidental or consequential damages. Therefore,
the above limitation(s) or exclusion(s) may not
apply to you.

If you have any questions concerning this or any other

product, please contact our Customer Service

Department at (716) 226 -9787. If a product must be

returned for any reason, please contact our Customer

Service Department to obtain a Returned Goods

Authorization number (RGA #) before you ship the

product back. Please write the RGA # clearly on the

package near the mailing label.

REV. H 4/5/04 PLITSTR87