Starbridge Lynx 524 Wireless ADSL Router
User Manual
Wireless ADSL Router USER MANUAL
NOTICE
This document contains proprietary information protected by copyright, and this Manual
and all the accompanying hardware, software, and documentation are copyrighted. All
rights are reserved. No part of this document may be photocopied or reproduced by
mechanical, electronic, or other means in any form.
The manufacturer does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty or representation, either
expressed or implied, with respect to the quality, performance, merchantability, or
fitness for a particular purpose of the software or documentation. The manufacturer
reserves the right to make changes to the hardware, software, and documentation
without obligation to notify any person or organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2009
All rights reserved.
Content
1 OVERVIEW........................................................................................................................1
1.1 FEATURES ........................................................................................................................... 1
1.2 PACKET CONTENTS ............................................................................................................ 3
1.3 SYSTEM REQUIREMENTS.................................................................................................... 3
1.4 FACTORY DEFAULTS........................................................................................................... 4
1.5 WARNINGS AND CAUTIONS .................................................................................................4
2 HARDWARE DESCRIPTION.............................................................................................5
3 HARDWARE INSTALLATION...........................................................................................7
4 PC CONFIGURATION GUIDE...........................................................................................8
4.1 LOCAL PC CONFIGURATION IN WINDOWS 95, 98, ME, XP................................................. 8
4.2 LOCAL PC CONFIGURATION IN WINDOWS 2000................................................................. 8
5 WEB-BASED MANAGEMENT GUIDE ..............................................................................9
5.1 LAN SETTING PAGE ............................................................................................................ 9
5.2 INTERNET ACCESS CONFIGURATION ...................................................................................9
QUICK SETUP............................................................................................................................. 9
5.3 WIRELESS SETTING ..........................................................................................................20
APPENDIX: FREQUENT ASKED QUESTIONS.................................................................24
Wireless ADSL Router USER MANUAL
1
1 Overview
Thank you for choosing our product. The Starbridge Lynx 524 Wireless ADSL
Router uses Broadcom’s CPE solution that fully complies with ADSL, ADSL2，
ADSL2+ and IEEE802.11b/g standards. It will provide your SOHO with
convenient Internet access.
1.1 Features
1.1.1 Data Rate
z Downstream data rate up to 24 Mbps
z Upstream data rate up to 1Mbps
1.1.2 ADSL Compliance
z ITU G.992.1 (G.DMT)
z ITU G.992.2 (G.Lite)
z ITU G.992.3 (G.DMT.BIS)
z ITU G.992.4 (G.lite.bis)
z ITU G.992.5
z ITU G.994.1 (G.hs)
z Compatible with all T1.413 issue 2 (full rate DMT over analog
POTS), and CO DSLAM equipment
z TR-069 compliant with ACS
1.1.3 Wireless
z Fully IEEE 802.11b & IEEE 802.11g compatible
z Wireless data rate up to 54 Mbps
z Operating in the unlicensed 2.4 GHz ISM band
z Supports 64/128 bits WEP security and user authentication
1.1.4 Network Protocol & Features
z Ethernet to ADSL Self-Learning Transparent Bridging
z Internet Control Message Protocol (ICMP)
z IP Static Routing
Wireless ADSL Router USER MANUAL
2
z Routing Information Protocol (RIP, RIPv2)
z Network Address Translation (NAT)
z Virtual Server, Port Forwarding
z Dynamic Host Configuration Protocol (DHCP)
z DNS Relay, DDNS
z IGMP Proxy
z Simple Network Time Protocol (SNTP)
z VPN pass-through (IPSec/PPTP/L2TP)
z Parent control
1.1.5 ATM Capabilities
z RFC 1483 Multi-protocol over ATM “Bridged Ethernet” compliant
z RFC 2364 PPP over ATM compliant
z RFC 2516 PPP over Ethernet compliant
z ATM Forum UNI3.1/4.0 PVC - Up to 8 PVCs
z VPI Range: 0-255
z VCI Range: 32-65535
z UNI 3.0 & 3.1 Signaling
z ATM AAL5 (Adaption Layer type 5)
z OAM F4/F5
1.1.6 FIREWALL
z Built-in NAT
z MAC Filtering
z Packet Filtering
z Stateful Packet Inspection (SPI)
z Denial of Service Prevention (DoS)
z DMZ
Wireless ADSL Router USER MANUAL
3
1.1.7 Management Support
z Web Based GUI
z Upgrade or update via FTP/HTTP
z Command Line Interface via Telnet
z Diagnostic Test
z Firmware upgrade-able for future feature enhancement
1.1.8 Operating System Support
z WINDOWS 98/SE/ME/2000/XP/VISTA
z Macintosh
z LINUX
1.1.9 Environmental
z Operating humidity: 10%-90% non-condensing
z Non-operating storage humidity: 5%-95% non-condensing
1.2 Packet Contents
The packet contents are as the following:
z ADSL ROUTER x 1
z External Splitter x 1
z Power Adapter x 1
z Telephone Line x 1
z Ethernet Cable x 1
z User Manual (CD) x 1
1.3 System Requirements
Before using this ROUTER, verify that you meet the following requirements:
z Subscription for ADSL service. Your ADSL service provider should
provide you with at least one valid IP address (static assignment or
dynamic assignment via dial-up connection).
z One or more computers, each contains an Ethernet 10/100M Base-T
network interface card (NIC).
Wireless ADSL Router USER MANUAL
4
z A hub or switch, if you are connecting the device to more than one
computer.
z For system configuration using the supplied web-based program: A web
browser such as Internet Explorer v5.0 or later, or Netscape v4.7 or
later.
1.4 Factory Defaults
The device is configured with the following factory defaults:
z IP Address: 192.168.1.1
z Subnet Mask: 255.255.255.0
z SSID: Lynx524
z Encapsulation: RFC 2516 LLC
z VPI/VCI: According to local information
1.5 Warnings and Cautions
z Never install telephone wiring during storm. Avoid using a telephone
during an electrical storm. There might be a risk of electric shock from
lightening.
z Do not install telephone jacks in wet locations and never use the product
near water.
z To prevent dangerous overloading of the power circuit, be careful about
the designed maximum power load ratings. Not to follow the rating
guideline could result in a dangerous situation.
z Please note that telephone line on modem must adopt the primary line
that directly outputs from junction box. Do not connect Router to
extension phone. In addition, if your house developer divides a
telephone line to multi sockets inside the wall of house, please only use
the telephone that has connected with the splitter of ADSL Router when
you access the Internet. Under the above condition, if you also install
telephone with anti-cheat-dial device, please pull out this kind of
telephone, otherwise ADSL Router may occur frequently off-line.
Wireless ADSL Router USER MANUAL
5
2 Hardware Description
Front Panel
LED Color Function
PWR Green
On: Power
Off: No power
ETH1-4 Green
On: LAN link established and active via LAN port
Blinking: ADSL data activity occurs
Off: No LAN link via LAN port
WLAN Green
On: The wireless module is ready and idle
Blinking: Data transmitting or receiving over WLAN
Off :The wireless module is not installed
DSL Green
On: ADSL link established and active
Quick blinking: ADSL is trying to establish a connection
Slow blinking: No ADSL link
INET Green
Blinking: ADSL data activity occurs.
Off: No ADSL data is being sent or received
Wireless ADSL Router USER MANUAL
6
Rear panel
Port Function
DSL
Connect the device to an ADSL telephone jack or splitter
using a RJ-11 telephone cable
RESET System reset or reset to factory defaults.
LAN
Connect the device to user’s PC's Ethernet port, or to the
uplink port on user’s hub/switch, using a RJ-45 cable
POWER Connect to the supplied power adapter
ON/OFF
Switch it on or off
ANT Antenna interface
Wireless ADSL Router USER MANUAL
7
3 Hardware Installation
This chapter shows user how to connect Router. Meanwhile, it introduces the
appropriate environment for the Router and installation instructions.
1. Using a telephone line to connect the DSL port of ROUTER to the Modem
port of the splitter, and using a other telephone line connect user’s
telephone to the PHONE port of the splitter, then connect the wall phone
jack to the LINE port of the splitter.
The splitter comes with three connectors as below:
LINE: Connects to a wall phone jack (RJ-11 jack)
ROUTER: Connects to the DSL jack of ROUTER
PHONE: Connects to a telephone set
2. Using an Ethernet Cable to connect the LAN port of the ROUTER to user’s
LAN or a PC with network card installed. Or using an USB cables to connect
the USB port of the ROUTER to user’s PC.
3. Connect the power cable to the PWR connector on ROUTER, then plug in
the AC power adapter to the AC power outlet, and then press the on-off
button.
Notes: Without the splitter and certain situation, transient noise from
telephone can interfere with the operation of the Router, and the
Router may introduce noise to the telephone line. To prevent this
from happening, a small external splitter must be connected to
each telephone.
Wireless ADSL Router USER MANUAL
8
4 PC Configuration Guide
4.1 Local PC Configuration in Windows 95, 98, ME, XP
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network” icon.
3. On the “Configuration” tab, select the TCP/IP network associated with
user’s network card and then click “Properties”.
4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP
address as 192.168.1.x (x can be a decimal number from 2 to 254.) like
192.168.1.2, and the subnet mask as 255.255.255.0.
5. On the “Gateway” tab, set a new gateway as 192.168.1.1, and then click
“Add”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with user’s ISP.
7. Click “OK” twice to confirm and save user’s changes.
8. User will be prompted to restart Windows. Click “Yes”.
4.2 Local PC Configuration in Windows 2000
1. In the Windows task bar, click the “Start” button, point to “Settings”, and
then click “Control Panel”.
2. Double-click the “Network and Dial-up Connections” icon.
3. In the “Network and Dial-up Connections” window, right-click the “Local
Area Connection” icon, and then select “Properties”.
4. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
5. In the “Internet Protocol (TCP/IP) Properties” dialog box, set the IP address
as 192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet
mask as 255.255.255.0 and the default gateway as 192.168.1.1. Then click
“OK”.
6. Configure the “DNS” tab if necessary. For information on the IP address of
the DNS server, please consult with user’s ISP.
7. Click “OK” twice to confirm and save user’s changes.
Wireless ADSL Router USER MANUAL
9
5 Web-based Management Guide
In order to use the web-based management software, it will be necessary to use
a computer that occupies the same subnet as the Router. The simplest way to
do this for many users will be to use DHCP server that is enabled by default on
the Router.
5.1 LAN setting page
Launch a web browser, such as Internet Explorer, and then use
http://192.168.1.1
to log on to the setting pages.
After user log in to the modem, the general status page appears.
5.2 Internet Access Configuration
The setup wizard will guide you to configure the DSL router to access Internet.
Quick Setup
If there aren’t any pre-configured PVCs in the router, you can find Quick Setup
option on the left of router configuration page. Or user can delete the PVCs
pre-configured to find the option.
1. From home page, click Quick Setup.
Click
Enter username
‘admin
’ and
password ‘admin
’
Wireless ADSL Router USER MANUAL
10
2. Unselect the check box to disable DSL Auto-connect process. Set VPI/VCI
value provided by your ISP.
a PPP over Ethernet (PPPoE)
1. Select PPP over Ethernet (PPPoE) as connection type, and select
LLC/SNAP-BRIDGING as encapsulation mode.
2. Input PPP Username & PPP Password and then click Next. The user interface
allows a maximum of 256 characters in the user name and a maximum of 32
characters in the password. Please remember to enable NAT and Firewall as below.
Wireless ADSL Router USER MANUAL
11
PPPoE service name can be blank unless your Internet Service Provider gives you a
value to enter.
Authentication method is default to Auto. It is recommended that you leave the
Authentication method in Auto, however, you may select PAP or CHAP if
necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for
PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you
to.
The gateway can be configured to disconnect if there is no activity for a specific period
of time by selecting the Dial on demand check box and entering the Inactivity
timeout. The entered value must be between 1 minute to 4320 minutes.
The PPP IP Extension is a special feature deployed by some service providers.
Unless your service provider specifically requires this setup, do not select it. If you
need to select it, the PPP IP Extension supports the following conditions:
Wireless ADSL Router USER MANUAL
12
It allows only one computer on the LAN.
The public IP address assigned by the remote using the PPP/IPCP
protocol is actually not used on the WAN PPP interface. Instead, it
is forwarded to the computer's LAN interface through DHCP. Only
one system on the LAN can be connected to the remote, since the
DHCP server within the ADSL gateway has only a single IP
address to assign to a LAN device.
NAPT and firewall are disabled when this option is selected.
The gateway becomes the default gateway and DNS server to the
computer through DHCP using the LAN interface IP address.
The gateway extends the IP subnet at the remote service provider to
the LAN computer. That is, the PC becomes a host belonging to the
same IP subnet.
The ADSL gateway bridges the IP packets between WAN and LAN
ports, unless the packet is addressed to the gateway's LAN IP
address.
3. Unselect Enable IGMP Multicast, and select Enable WAN Service and then
click Next
4. Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In
this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the
assignment of IP addresses on your local network (LAN only).
Wireless ADSL Router USER MANUAL
13
Item
Description
IP address
This is the IP address that other devices on your local network
will use to connect to the modem.
Subnet mask
This defines the size of your network. The default is
255.255.255.0.
Disable / Enable
DHCP server
The DHCP server assigns an IP addresses from a pre-set pool of
addresses upon request from DHCP client (e.g. your computer).
Do not disable the DHCP server unless you wish to let another
device handle IP address issuance on the local network.
Start / end IP
address
This is the beginning and ending range for the DHCP server
addresses.
Lease time
The amount of time before the IP address is refreshed by the
DHCP server.
Configure the
second IP
address and...
Use this feature to create a public network on your local LAN,
accessible from the Internet. By assigning an address to this
interface and then statically setting your LAN clients to the same
network, the LAN clients are accessible from the public network
Wireless ADSL Router USER MANUAL
14
(e.g. FTP or HTTP servers).
5. Set SSID for wireless network if user enabled the wireless function.
6. Make sure that the settings below match the settings provided by your ISP.
7. Click on the Save/Reboot button to save your configurations.
b PPP over ATM (PPPoA)
1. Select PPP over ATM (PPPoA) as connection type, and select VC/MUX as
encapsulation mode.
Wireless ADSL Router USER MANUAL
15
2. Input PPP Username & PPP Password and then click Next. The user interface
allows a maximum of 256 characters in the user name and a maximum of 32
characters in the password. Please remember to enable NAT and Firewall as below.
Authentication method is default to Autoc. It is recommended that you leave the
Authentication method in Auto, however, you may select PAP or CHAP if
necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for
Wireless ADSL Router USER MANUAL
16
PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you
to.
The gateway can be configured to disconnect if there is no activity for a specific period
of time by selecting the Dial on demand check box and entering the Inactivity
timeout. The entered value must be between 1 minute to 4320 minutes.
The PPP IP Extension is a special feature deployed by some service providers.
Unless your service provider specifically requires this setup, do not select it. If you
need to select it, the PPP IP Extension supports the following conditions:
It allows only one computer on the LAN.
The public IP address assigned by the remote using the PPP/IPCP
protocol is actually not used on the WAN PPP interface. Instead, it
is forwarded to the computer's LAN interface through DHCP. Only
one system on the LAN can be connected to the remote, since the
DHCP server within the ADSL gateway has only a single IP
address to assign to a LAN device.
NAPT and firewall are disabled when this option is selected.
The gateway becomes the default gateway and DNS server to the
computer through DHCP using the LAN interface IP address.
The gateway extends the IP subnet at the remote service provider to
the LAN computer. That is, the PC becomes a host belonging to the
same IP subnet.
The ADSL gateway bridges the IP packets between WAN and LAN
ports, unless the packet is addressed to the gateway's LAN IP
address.
3. Unselect Enable IGMP Multicast, and select Enable WAN Service and then
click Next
Wireless ADSL Router USER MANUAL
17
4. Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In
this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the
assignment of IP addresses on your local network (LAN only).
Item
Description
IP address
This is the IP address that other devices on your local network
will use to connect to the modem.
Subnet mask
This defines the size of your network. The default is
255.255.255.0.
Disable / Enable
DHCP server
The DHCP server assigns an IP addresses from a pre-set pool of
addresses upon request from DHCP client (e.g. your computer).
Do not disable the DHCP server unless you wish to let another
device handle IP address issuance on the local network.
Start / end IP
address
This is the beginning and ending range for the DHCP server
addresses.
Lease time
The amount of time before the IP address is refreshed by the
DHCP server.
Wireless ADSL Router USER MANUAL
18
Configure the
second IP
address and...
Use this feature to create a public network on your local LAN,
accessible from the Internet. By assigning an address to this
interface and then statically setting your LAN clients to the same
network, the LAN clients are accessible from the public network
(e.g. FTP or HTTP servers).
5. Set SSID for wireless network if user enabled the wireless
6. Make sure that the settings below match the settings provided by your ISP.
7. Click on the Save/Reboot button to save your configurations.
c Bridging (RFC 2684)
Select the bridge operating mode if your ADSL service provider tells you that you
should. To configure bridging, do the following:
1. Select Bridging (RFC 2684) as connection type.
Wireless ADSL Router USER MANUAL
19
2. Select the appropriate Encapsulation mode and click Next. The following
screen appears:
3. Enable or disable bridge service and enter a bridge service name. Click Next.
Configure the DSL Router IP Address and Subnet Mask for your Local Area Network
(LAN).
4. Set SSID for wireless network if user enabled the wireless function.
5. The summary page presents the entire configuration summary. Click Save if the
settings are correct or Back to change any of the settings.
Wireless ADSL Router USER MANUAL
20
Note: If you want to cancel all modification that you do on the Router, please
select from “ManagementÖSettingÖRestore Default Settings” to restore
factory default settings.
5.3 Wireless setting
5.3.1 Basic
Enable Wireless: Click this check box to enable the wireless network function.
Hide Access Point: Checking this box can hide the SSID of this access point. Then
other people in the network cannot find the SSID of this device.
Clients Isolation: Enable it if you don’t want your wireless clients to communicate
with each other.
Wireless ADSL Router USER MANUAL
21
SSID: The system will detect the SSID of your router and displayed in this field for
your reference. The default SSID is Lynx524.
The SSID is the identification characters of a router. The default words will be shown on
this page. If you do not check the Hide Access Point item, the router will periodically
broadcasts its SSID to allow the wireless clients within the range to recognize its presence.
This can create a security hole since any wireless clients which got the broadcast might
associate to your system.
Please be noted that if you want to communicate, all wireless clients should use the
same SSID with the router or access point.
Country: For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
5.3.2 Security
To configure security features for the Wireless interface, please open Security item
from Wireless menu. This web page offers nine authentication protocols for user to
secure user’s data while connecting to networks. There are four selections including
Open, Shared, 802.1X, WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA-WPA2,
Mixed WPA-WPA2-PSK. Different item leads different web page settings. Please read
the following information carefully.
The wireless security page allows user to configure the security features of user’s
wireless network.
There are several security methods to choose from, depending on user’s
needs and the capabilities of user’s wireless machines.
Wireless ADSL Router USER MANUAL
22
WEP open and WEP shared —WEP is an encryption scheme that is used
to protect user’s wireless data communications. WEP uses a combination
of 64-bit keys or 128-bit keys to provide access control to user’s network
and encryption security for every data transmission. To decode a data
transmission, each wireless client on the network must use an identical
64-bit or 128-bit key. WEP is an older wireless encryption method that is
not as hard to break as the more-recent WPA.
802.1x — In 802.1x (also known as RADIUS), a separate machine called an
authentication server receives a user ID and password. It grants or denies
access based on whether the ID and password match any entries in its
account list. User can optionally enable WEP encryption with this option.
Because it requires a separate machine acting as the authentication server,
802.1x is most often used in business environments.
WPA— WPA is a more recent encryption method that addresses many of
the weaknesses in WEP. Any client capable of WPA encryption should use
it instead of WEP.
WPA (PSK) — This is WPA encryption combined with a pre-shared key
(PSK), which is a text string known only to the gateway and authorised
wireless clients. The gateway rejects the login if the client's PSK does not
match.
WPA2 — WPA2 is a more advanced encryption method than WPA. Because
it is a more recent standard, some of user’s wireless devices might not be
able to use it.
WPA2 (PSK) — this option uses WPA2 with a pre-shared key.
WPA2 and WPA— This option supports WPA2/WPA encryption for devices
capable of one or the other standard. The gateway automatically detects
whether a particular device can use WPA2 or WPA.
Wireless ADSL Router USER MANUAL
23
WPA2 AND WPA (PSK) — this has WPA2 or WPA encryption based on
client abilities, as well as a pre-shared key.
After making changes, click Apply to save.
Wireless ADSL Router USER MANUAL
24
Appendix: Frequent Asked Questions
Q: None of the LEDs are on when user power on the ADSL router?
A: Please make sure what user use is the power adaptor attached with the ADSL
router package，and check the connection between the AC power and ADSL
router.
Q: DSL LED does not turn on after connect telephone line?
A: Please make sure what user use is the standard telephone line (as attached with
the package), make sure the line is connected correctly and check whether there
is poor contact at each interface. Wait for 30 seconds to allow the ADSL router
establishes connection with user ADSL operator .
Q: DSL LED is in the circulation of slow-flashing and fast-flashing after connect
telephone line?
A: This situation means the ADSL router is in the status of failing to establish
connection with Central Office. Please check carefully and confirm whether the
ADSL router has been installed correctly.
Q: LAN LED does not turn on after connect Ethernet cable?
A: Please make sure Ethernet cable is connected hub/PC and ADSL router correctly.
Then please make sure the PC/hub have been power on.
Please make sure that user use parallel network cable to connect UpLink port of
hub, or use parallel network cable to connect PC. If connect normal port of hub
(not UpLink port), user must use cross-cable. Please make sure that user’s
network cables meet the networking requirements above.
Q: PC cannot access the Router?
A: Please make sure that all devices communicating with the device must use the
same channel (and use the same SSID). Otherwise user’s PC will not find the
wireless Router.
Q: PC cannot access the Internet?
A: First check whether PC can ping the interface Ethernet IP address of this product
successfully (default value is 192.168.1.1) by using ping application. If ping
application fails, please check the connection of Ethernet cable and check
whether the states of LEDs are in gear.
If the PC uses private IP address that is set manually (non-registered legal IP
address), please check:
1. Whether IP address of the PC gateway is legal IP address. Otherwise please
use the right gateway, or set the PC to Obtain an IP address automatically.
2. Please confirm the validity of DNS server appointed to the PC with ADSL
operator. Otherwise please use the right DNS, or set the PC to Obtain an IP
address automatically.
3. Please make sure user have set the NAT rules and convert private IP
address to legal IP address. IP address range of the PC that user specify
should meet the setting range in NAT rules.
4. Central Office equipment may have problem.
5. The country or the wireless network type user selected is wrong.
Q: PC cannot browse Internet web page?
Wireless ADSL Router USER MANUAL
25
A: Please make sure DNS server appointed to the PC is correct. User can use ping
application program to test whether the PC can connect to the DNS server of the
ADSL operator.
Q: Initialization of the PVC connection failed?
A: Be sure that cable is connected properly from the DSL port to the wall jack. The
DSL LED on the front panel of the ADSL router should be on. Check that user’s
VPI, VCI, type of encapsulation and type of multiplexing setting are the same as
what user collected from user’s service provider, Re-configure ADSL router and
reboot it. If user still can not work it out, user may need to verify these variables
with the service provider.
If the cause is not above given，please contact user’s local service
provider!
*** Caution ***
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes of modifications not expressly approved by the party responsible for compliance could void
the user ’s authority to op erate the equipment.
FCC statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with any
other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter”.
FCC Part 68 Statement
This equipment complies with Part 68 of the FCC rules. This unit bears a label, which contains the
FCC registration number and ringer equivalence number (REN). If requested, this information must
be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this happens the telephone company will provide
advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact our
company. If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
Loading...