Star SST-2HDC Service Manual

DRAWER ROLL/

SST-2HDC

BUN WARMER

MODEL

SST-12
SST-25

SST-45 & SST-45HC

Installation and

Operation

Instructions

2M-Y5049 Rev. H 5/10/11

SST-25

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business

8:00 am to 4:30 p.m. Central Standard Time

Hours:
Telephone: [phone] Local [phone]
Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations. For equipment to be used by the general public, please
contact the factory.

CAUTION

INSTALLATION

This bun warmer is equipped for the voltage shown on the nameplate. It will operate on alternating
current only, however, the correct voltage must be applied.

CAUTION

DO NOT CONNECT TO DIRECT CURRENT (DC).

GENERAL OPERATING PROCEDURES

When you turn knob to temperature required, pilot light will go on until temperature in warmer is
reached, then pilot light will go off. The thermostat will automatically maintain proper temperature,
using current as needed. To shut off current, turn knob to left.

To keep rolls soft and fresh, turn knob to a low position. Higher settings should be used only for
short periods. The thermostat holds the temperature to which it is set. Keep the drawers as full as
possible. When adding new rolls to drawer, pull the rolls and buns that are left in drawer toward the

front and use them rst, giving time for new rolls to become heated. Do not heat the rolls more than

once, as they will not be palatable if reheated. If they dry out, reduce temperature.

CORD, PLUG AND GROUND INSTRUCTIONS

For your protection, this appliance is equipped with a 3-conductor cord, with a grounding type plug.
Connect only to a grounding receptacle.

NOTE: This unit may smoke and have a slight odor when rst used because the insulation is

new. We suggest before using, you turn the thermostat to a high heat position and let unit heat for
approximately two (2) hours.

CLEANING

To remove the drawer for cleaning, rst pull the drawer out until it stops. Second, remove the interior

pan. Third, grasp the drawer assembly with both hands. Fourth, lift the drawer in an upward
direction, while slowly pulling out. This will disengage the drawer from the drawer stops. To re-install
the drawer, reverse the procedure. For retaining the high lustre on the stainless steel, use a non­abrasive standard stainless steel cleaner.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative or a local service company for service or required
maintenance.

3