Star PC-6 Service Manual

CONDIMENT

DISPENSERS

MODEL

CD1PG,

CD2P, CD2P-2,

CD2P-3, CD2PG-3,

CD3, CD5,

PCD-5, PCD-6, PCB-6

Installation and

Operation

Instructions

2M-Y8713 Rev. I 6/22/2006

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone]
Fax: [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

GENERAL INSTALLATION DATA

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and

experienced in its operation and is not sold for consumer use in and around the home nor
for use directly by the general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels

associated with the unit prior to putting it into operation. Make sure all people associated
with its use understand the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed.

This unit has been tested and carefully packaged to insure delivery of your unit in perfect
condition. If equipment is received in damaged condition, either apparent or concealed, a
claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is

unpacked, a request for inspection of concealed damage must be made with carrier within
15 days. Be certain to retain all contents plus external and internal packaging materials for

inspection. The carrier will make an inspection and will supply necessary claim forms.

CAUTION

THESE UNITS ARE NOT ACCEPTABLE FOR POTENTIALLY HAZARDOUS FOODS.

PUMP CLEANING

Before using and at least daily, disassemble the pump and wash all parts.

To disassemble pump:

1. Unscrew nut-cylinder. Pull pump-plunger from pump chamber.

2. Unscrew knob from plunger assembly and disassemble.

3. Unscrew nut-sleeve-tube from dispense tube. Remove cover from pump assembly.

4. Remove "U" pin from pump assembly and disengage dispense tube from pump
chamber.

5. Remove balls from pump chamber.

6. Wash all parts thoroughly in hot soapy water and rinse thoroughly. Use 18" long brush
to clean inside of dispensing tube. Reassemble pump. When reassembling pump, wet
o-ring with edible vegetable oil, then reassemble. Make sure all parts are in their proper

places.

PRIMING PUMP

Three (3) strokes of the pump plunger are necessary to initially prime and vend thick food
products.

If the pump does not dispense product properly, remove the plunger assembly from the pump
and make sure the plunger "o" ring is in place on the pump plunger. If the "o" ring is missing,
disassemble the pump parts and make certain the "o" ring is not in the pump plunger tube,
pump chambers or vend tube before replacing "o" ring.

CAUTION
FAILURE TO DO THIS CAN CAUSE A BROKEN "O" RING TO BE PUMPED OUT
WITH THE FOOD BEING VENDED.

REMOVAL AND CLEANING - CD2P, CD1PG

Remove pumps and clean according to pump cleaning instructions.
To clean the body and pans, use a mild, non-abrasive cleaner, rinse and dry thoroughly.

Re-install pans and pump assemblies into CD2P and CD1PG bodies.

3