Star HCT13S, HCTE13M Operators Manual

CONTACT

TOASTER

MODEL

HCT13M, HCT13S

HCTE13M, HCTE13S

Installation and

Operation

Instructions

2M-Z19028 Rev. F 11/2018

IL2845b

HCT13 & HCTE13

(Shown with optional butter wheel)

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change without notice. While Star International Holdings Inc., Company exercises good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information provided, the user assumes all risks in connection with such use.

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure a faster service.

Authorized Service Agent Listing

Model No.

Serial No.

Voltage

Purchase Date

Reference the listing provided with the unit

for an updated listing go to:

Website: www.star-mfg.com E-mail customerservice@star-mfg.com

Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time Hours:

Telephone:

Fax:

E-mail

Website:

Mailing Address: Star Manufacturing International Inc.,Company

(800)-264-7827

(314)-781-2714

customerservice@star-mfg.com

www.star-mfg.com

265 Hobson St. Smithville, Tennessee 37166,

U.S.A

2M-Z19028; Holman Contact Toaster

TABLE OF CONTENTS

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features & Benets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Uncrating & Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assembly & Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Toaster Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Daily Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 & 6

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17

SPECIFICATIONS

19.25”

24.662”

20”

Electrical Specicaons

Model Voltage Hz Ph Amps Watts Powercord

HCTE13M

HCTE13S

208V 60

230V 50 12 2750 CEE7/VII

240V

208V 12.25 2550 6-20P

230V 50 10.5 2450 CEE7/VII

240V 60 11 2650 6-20P

13.5 2800 6-20P

12.5 3000 6-20P

IL2844

HCT13M

HCT13S

208V 60

230V 50 12 2750 CEE7/VII

240V

208V 12.25 2550 6-20P

230V 50 10.5 2450 CEE7/VII

240V 60 11 2650 6-20P

13.5 2800 6-20P

12.5 3000 6-20P

FEATURES & BENEFITS

Namplate

B C

IL2846a

A Platen Height Indicator Indicates the height of the upper platen

B Platen Support Bracket Keeps the upper platen in the up position, useful while cleaning

Interrupts the heater tube connections if the air temperature in the control box

C High Limit

D Platen Height Knob Controls the height of the upper platen

E Locking Platen Latch Keeps the upper platen in the down position.

F Control Board Controls the conveyor speeds, turns unit on & off, & temperature settings.

G Foot Silicone foot keeps unit rmly in place.

H Crumb Tray Slide out crumb tray used to catch particles from falling

I Toaster Chute Removable Chute returns product for easy access.

J Conveyor Takes the heel and crown separately through their toasting process

K Burn Guard Protects users from touching the conveyor belt

Durable Non-Stick Coated

Sheet

M Upper Platen Assy Heating surface designed to toast the product as it slides across the surface

exceeds 190°F (88°C). This limit switch can be reset manually by pushing the button in the center of the switch.

Non-Stick surface between the upper platen and the product, allowing the product to slide easily through the toasting process.

N Optional Butter Wheel Saves time for preparing buns for toasting

2M-Z19028; Holman Contact Toaster

CAUTION

GENERAL INFORMATION

This equipment is designed and sold for commercial use only by personnel trained and

experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels

associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation & safety before they use the unit.

INSPECTION

UN-CRATING AND INSPECTING

Unpack the unit and components from the shipping container. Remove all visible packing

material and those from inside the cooking chamber. If damage is discovered, le a claim

immediately with the carrier that handled the shipment. Do not operate the unit if it was damaged during shipping. All shipping containers should be checked for freight damage both visible and concealed. This unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within 15 days. Be certain to retain all contents plus external and internal packaging materials for inspection. The carrier will make an inspection and will supply necessary claim forms.

ELECTRICAL CONNECTION

Disconnect the unit from the power source before installing or removing any parts.

Be absolutely sure that the ground connection for the receptacle is properly wired.

Do not connect equipment to power without proper ground connections. Improper grounding may result in personal injury or death.

CAUTION

Allow enough space around the toaster for adequate ventilation. Do not operate the unit

without the crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit and follow their instructions.

WARNING

Before making any electrical connection to this unit, check that the power

supply is adequate for the voltage, amperage and requirements stated on the rating plate. A wiring diagram is included.

WARNING

DO NOT CUT OR REMOVE THIS PLUG OR THE GROUNDING PRONG FROM

THE PLUG. FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS INJURY.

WARNING

CONNECT/PLUG UNIT INTO DEDICATED A. C. LINE ONLY SPECIFIED ON THE

DATA PLATE OF THE UNIT.

CAUTION

SOME SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD

BE TAKEN WHILE USING THIS UNIT.

ASSEMBLY AND INSTALLATION

The unit was shipped fully assembled and ready to plug into a standard outlet specied for its voltage and amp draw. If improper electrical supply is determined, contact a qualied electrician

prior to using the unit. Removal and replacement of the power cord and plug voids the warranty. For assistance, contact your local authorized service agent for service or required maintenance.

1. Place the unit in its operating location.

2. Wipe down the exterior with a damp cloth.

3. Place the Toaster Chute & Crumb Tray into position.

4. Unlock the Platen Latch and raise the platen, move the Platen Support Bracket to hold the platen in the up position.

Sheet Retainer

5. Loosen the Sheet Retainer and install the non-stick sheet into position, and secure.

Non-Stick Sheet

6. Lower the Platen and latch in place.

CAUTION

Failure to use non-stick sheets can lead to damaging the unit and a loss of warranty. The durable non-stick coated sheets are not a warranty item.

TOASTER SETTINGS

Before using the unit for the rst time,

test the pass time of the conveyor belt. The pass time through the toaster should be between 16 to 20 seconds for standard setting.

Crumb Tray

Toaster Chute

Platen Support Bracket

IL2848a

Platen Latch

1. Turn unit ON and wait for it to complete the PRE-HEAT process.

2. Set the Platen height by adjusting the two (2) Platen Height Knobs on top of the unit.

3. Make sure the platen lock is on.

4. Place a bun on the conveyor belt, cut side up, “HEEL” on one side and “CROWN” on the other.

IF TO DARK: Decrease TEMP.

IF TO LIGHT: Increase TEMP. or lower platen

2M-Z19028; Holman Contact Toaster

+ 14 hidden pages