Star GR14SPTKG240 Service Manual

®

®

®

®

®

SPLIT-LID TABLE TOP

TWO SIDED

TOASTER

MODEL

GR14SPTK-UK, GR14SPTK-CE

GR14SPTKG-CE, GR14SPTKG240

GR14SPTK-TAI

Installation and

Operation

Instructions

2M-Z9194 Rev. D 1/09/2013

GR14SPTK-UK

1

SAFETY SYMBOL

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance. Please record the model number, serial
number, voltage and purchase date in the area below and have it ready when you call to ensure a faster

service.

Model No.

Serial No.

Voltage

Purchase Date

FOR SERVICE CONTACT:

Middleby Worldwide, UK

Telephone: [phone]

Email: [e-mail]

Middleby Worldwide, Europe

Telephone: [phone]

Email: [e-mail]

Middleby Taiwan Corporation

Telephone: [phone]

2M-Z9194 GR14SPTK SPLIT-LID TABLE TOP TWO SIDED TOASTER

2

2

CAUTION

WARNING

GENERAL INSTALLATION DATA

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels associated with

the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If
equipment is received in damaged condition, either apparent or concealed, a claim must be made
with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make

an inspection and will supply necessary claim forms.

INSTALLATION

1. Plug the unit into a dedicated 230 VAC line with United Kingdom BS 1363A receptacle.

2. DO NOT plug into a 120V line. Doing so will damage the unit and void the warranty.

3. Each machine has been properly wired and inspected at the factory for operation on the voltage

and type of current specied on the nameplate.

DO NOT CONNECT TO ANY TYPE OF CURRENT OTHER THAN 230 VAC OR THE
MACHINE WILL BE SERIOUSLY DAMAGED.

2M-Z9194 GR14SPTK SPLIT-LID TABLE TOP TWO SIDED TOASTER

INITIAL START UP

Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).

Before using the unit for the rst time, wipe down the exterior and toasting area with a damp cloth.

Take to a well ventilated area and heat for approximately 30 minutes. The grill may emit a small
amount of smoke as the cooking surfaces reaches 232°C. Do not be alarmed, as the smoke is
caused by oils associated with the manufacturing process and will stop when the burn off is complete.

Brush off any debris from the toasting surface.

SEASONING THE COOKING SURFACES

FIRST TIME SEASONING

Follow your company/corporate guidelines for seasoning cooking surfaces. or

1. Bring the grill to 148°C and leave it on while doing the next three steps.

2. Brush the cooking surfaces with a release agent. If using an aerosol agent,

rst apply into a cup and then brush onto cooking surface.

3. Let sit for 20 minutes, and then wipe clean using a warm damp cloth.

DAILY SEASONING

The grill should not require much seasoning while in use. In most cases, brush a light coating of the
baking release agent in the morning and occasionally throughout the day will be enough to prevent any

sticking. It is not necessary to spray before grilling each item.

PRESET TIMES AND TEMPERATURES

If adjustments are required, please refer to the time or temperature programming section in this
manual.

°F/°C CONVERSION

To change the temperature display from °F to °C or from °C to °F, hold the TEMP button while the unit is
turned off. While holding the TEMP button, turn the unit on. The display will be the changed temperature
mode. To change back, repeat the procedure.

3

OPERATING INSTRUCTIONS

1. Turn the unit on by placing the switch in the ON position. The HEAT ON indicator, program number

and display will ash indicating the unit is heating. When the preset temperature is reached, the
heating light, display and program light indicator will stop ashing followed by 3 beeps. (Initial startup

heating time is approximately 30 minutes).

2. Place product on the bottom cooking surface of the unit and close the lids.

3. Press the PROGRAM button and let the displayed time count down to "0" at which time the unit will
beep. To turn off the beeper, press the PROGRAM button again.

4. Raise the lid until it engages into the rst detent and remove food. Using a spatula, scrape residue

into the grease catcher tray.

NOTE: Metal utensils may be used, however, using nonmetal utensils will prolong the life of the

cooking surface.

5. Turn the unit off when it is not in use.

TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Startup:

1. The preset time will ash until the preset temperature is reached.

2. When the control reaches the preset temperature, time display, the HEAT ON indicator and program

indicator will stop ashing and the alarm will beep three times.

Temperature:

1. To view the actual temperature, press and hold the TEMP button. The display will read "Lo" if the
temperature is below 135°C (273°F) and "Hi" if the temperature is above 300°C (573°F).

To Program Time and Temperature:

1. Press and hold TEMP (actual temperature displays).

2. While holding TEMP, press and hold any program button on the left for one second. The LED above
the program number will light and the display will read "_ _ _ _." Enter the four-digit security code
sequence: 4, 3, 2, 1. The security code will not show on the display. Once the correct sequence has

been entered, the preset time will be displayed and the LED for that program will begin to ash.

3. Set the time with the "+ or -" buttons.

4. Press the TEMP button to save the time.

5. The preset temperature will now be displayed.

6. Set the desired temperature for this program using the "+ or -" buttons.

7. Press the TEMP button to save the temperature and to exit the programming mode for this

program. The LED will stop ashing but will remain lit.

8. Press any other program button within 15 seconds to continue programming without
re-entering the security code.

9. While programming a program (LED is ashing), if no input is received for 15 seconds the unit will

revert to normal operation and the security code must be re-entered.

NOTE: Temperature settings are done with the Left side buttons only. The time settings
programmed on the left buttons will also be programmed onto the Right side. See the next
section to make time changes to the Right side only. Each programming change must be

saved by pressing the TEMP button!

Right Side (Timer only):

1. To change the time on right, press and hold the TEMP button, then press and hold any program
button on the right for one second. The LED above the program button will light and the right
display will read "_ _ _ _." Enter the four-digit security code sequence: 4, 3, 2, 1. The security

code will not show on display. Once the correct sequence has been entered, the preset time will

be displayed and the LED for that program will begin to ash.

2. Set the time with the "+ or -" buttons.

3. Press the TEMP button to save the time.

4. TheLEDwillstopashingbutwillremainlit.

4

2M-Z9194 GR14SPTK SPLIT-LID TABLE TOP TWO SIDED TOASTER