Star 502FD Parts List

®

®

®®®

ELECTRIC HOT PLATE

MODELS

501FD, 502D, 502FD, 502DS

Installation and

Operation

Instructions

2M-Z6062 Rev. A 10/14/113

502D

502FD

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone]

Fax: [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

CAUTION

Specications

Electrical Specications Dimensions

Model Voltage kW Width Depth Height

501FD 208/240 1.95/2.6

501FD-208V 208V 2.6

502D

502DS

502FD 3.9/5.2

208/240

3.1/4.2

12” (30.4cm)

12” (30.5cm) 28 (71.1cm)

17.25”

(43.8cm)

10.7”

(27.2cm)

11 5/8”

(29.5cm)

GENERAL OPERATING INSTRUCTIONS

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations. For equipment to be used by the general public, please
contact the factory.

The Star-Max Electric Hot Plates are equipped for the voltage indicated on the nameplate mounted
on the front panel. This unit is designed to operate on alternating current (A.C.), two wire single phase
service only.

DO NOT CONNECT TO DIRECT CURRENT (D.C.).

Total Connected Load:

502FD: at 240 Volts, Wattage is 5,200.
at 208 Volts, Wattage is 3,900.

502D/502DS: at 240 Volts, Wattage is 4,200.
at 208 Volts, Wattage is 3,150.

CAUTION

CAUTION

INSTALLATION

For your protection, we recommend that a qualied electrician install this appliance. The electrician

should be familiar with electrical installations and your local electrical requirements. The external

wiring should be in conduit or an approved type of exible cable and of suitable size to carry the load.

The supply circuit should be properly fused and equipped with a means of disconnecting as required
by local electrical code. The body of the hot plate should be grounded (Do not ground to a gas
supply pipe). The connections are made in this unit at the pigtail leads located in the junction box on
the back of the unit. To gain access to the pigtail leads remove cover on junction box.

LOCATE THE UNIT

Do not install the unit closer than 1 inch from a side wall and/or closer than 1 inch from a rear wall.

LEVELING UNIT

Level unit by adjusting the (4) feet for accurate and perfect line up with other Star-Max series units.

DO NOT INSTALL WITHOUT FEET.

USE ONLY FLAT BOTTOM PANS AND POTS! DO NOT USE RAISED BOTTOM UTENSILS
OR BUCKETS! GOOD HEAT TRANSFER DEPENDS UPON GOOD CONTACT BETWEEN
THE ELEMENT AND POT.

NOTE: Using a 12” diameter or larger pan/pot may cause damage to the element or internal wiring.
Such damages are not covered by warranty.

Two (2) heating elements are used. For the 502FD each element draws 2,600 Watts on 240 Volts and
1,950 Watts on 208 Volts. For the 502D and DS each element draws 2,100 Watts on 240 Volts and

1,575 Watts on 208 Volts. Each element is controlled by an innite position switch. The right control

knob controls the rear cooking element and the left control knob controls the front cooking element.
On “HI” the element delivers uninterrupted full heat. Between “LO” and “5” any desired amount of heat
can be obtained between 6% and 60% of full heat.

Signal lights are provided above the control knobs to give a visual check if either one or both heating
units are turned on.

3