Star 3W SERIES Installation And Operation Instructions Manual

3 1/2 QUART

WARMERS

MODEL

3W SERIES

Installation and

Operation

Instructions

2M-Y8316 Rev. L 6/30/2008

3WLA-B

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business

8:00 am to 4:30 p.m. Central Standard Time

Hours:
Telephone: [phone] Local [phone]
Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

SPECIFICATIONS:

MODEL 3WSA-HS 120V - STAINLESS STEEL WITH PUMP and HEATED SPOUT

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 515wt; 4.3a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 11 lbs.

MODEL 3WSA-P 120V - STAINLESS STEEL WITH PUMP

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 500wt; 4.2a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WLA-W 120V - LIGHTED, INCLUDES "N", "BQ", "C", "CD", "F", and "S" SIGNS
(INSET WITH COVER SSB-4 or SSB-4H, and LADLE - OPTIONAL)

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 10-1/2" D x 9" W x 12-3/4" H
Net Weight: 10.5 lbs.

MODEL 3WLA-NP, -FP 120V - LIGHTED WITH PUMP and SIGN: N* or F*

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WLA-B 120V - LIGHTED WITH BUTTER PUMP and
GOLDEN FLAVOR POPCORN SIGN

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WSA-W 120V - STAINLESS STEEL, (INSET WITH COVER SSB-4 OR SSB-4H, and
LADLE - OPTIONAL)

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 500wt; 4.2a.
Dimensions: 10-1/2" D x 9" W x 12-3/4" H

Net Weight: 10.5 lbs.

MODEL 3WLA-NHS, -CDHS 120V - LIGHTED WITH NACHO or CHILI SIGN
WITH PUMP and HEATED SPOUT

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 545wt; 4.5a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 11 lbs.

3

MODEL 3WSA-HS 240V - STAINLESS STEEL WITH PUMP and HEATED SPOUT

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 473wt;2.1a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 11 lbs.

MODEL 3WSA-P 240V - STAINLESS STEEL WITH PUMP

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 460wt; 2a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WSA-B 240V - STAINLESS STEEL WITH BUTTER PUMP

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 460wt; 2a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H
Net Weight: 10.5 lbs.

MODEL 3WLA-P 240V - LIGHTED WITH PUMP and N* and F* SIGNS

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 487wt; 2.1a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WLA-B 240V- LIGHTED WITH BUTTER PUMP and
GOLDEN FLAVOR POPCORN SIGN

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 487wt; 2.1a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 10.5 lbs.

MODEL 3WLA-HS-240V - LIGHTED WITH PUMP and HEATED SPOUT and
N* and CD* SIGNS

Capacity: 3-1/2 quarts
Electrical: 240V; 50/60 cycle; single phase; 501wt; 2.2a.
Dimensions: 10-1/2" D x 9" W x 15-1/2" H

Net Weight: 11 lbs.

MODEL 3WSA-4H 120V - STAINLESS STEEL WITH INSET and COVER

Capacity: 4-1/8 quarts
Electrical: 120V; 50/60 cycle; single phase; 500wt; 4.2a.
Dimensions: 11" D x 9" W x 11 3/4" H

Net Weight: 11 lbs.

MODEL 3WLA-4H 120V - LIGHTED WITH INSET and COVER and 6* SIGNS

Capacity: 4-1/8 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 11" D x 9" W x 11 3/4" H

Net Weight: 11 lbs.

4

MODEL 3WSA-4H 240V - STAINLESS STEEL WITH INSET and COVER

Capacity: 4-1/8 quarts
Electrical: 240V; 50/60 cycle; single phase; 460wt; 2a.
Dimensions: 11" D x 9" W x 11 3/4" H

Net Weight: 11 lbs.

MODEL 3WLA-4H 240V - LIGHTED WITH INSET and COVER and 6* SIGNS

Capacity: 4-1/8 quarts
Electrical: 240V; 50/60 cycle; single phase; 487wt; 2.1a.
Dimensions: 11" D x 9" W x 11 3/4" H

Net Weight: 11 lbs.

MODEL 3WLA-BQR 120V - LIGHTED (NO SIGNS)

Capacity: 3-1/2 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 10-1/2" D x 9" W x 11 3/4" H

Net Weight: 11 lbs.

MODEL 3WLA-BQ*, -C*, -CD*, -F*, -N* -120V - LIGHTED WITH SIGN

Capacity: 4-1/8 quarts
Electrical: 120V; 50/60 cycle; single phase; 530wt; 4.4a.
Dimensions: 10-1/2" D x 9" W x 12-3/4" H

Net Weight: 11 lbs.

MODEL 3WLA-W 240V LIGHTED INCLUDES 6* SIGNS (INSET WITH COVER SSB-4
OR SSB-4H, AND LADLE - OPTIONAL)

Capacity: 4-1/8 quarts
Electrical: 240V; 50/60 cycle; single phase; 487wt; 2.1a.
Dimensions: 10-1/2" D x 9" W x 12-3/4" H

Net Weight: 11 lbs.

MODEL 3WSA-W 240V STAINLESS STEEL (INSET WITH COVER SSB-4
OR SSB-4H, AND LADLE - OPTIONAL)

Capacity: 4-1/8 quarts
Electrical: 240V; 50/60 cycle; single phase; 460wt; 2a.
Dimensions: 10-1/2" D x 9" W x 12-3/4" H
Net Weight: 11 lbs.

NOTES:

Bowl 3QT, SSB - OPTIONAL FOR ALL MODELS

* N = Nacho Sign, F = Fudge Sign, CD = Chili Dog Sign, BQ = BBQ Sign, C = Chili Sign, S = Soup Sign

5

CAUTION

WARNING

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels associated with
the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This unit
has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equip­ment is received in damaged condition, either apparent or concealed, a claim must be made with the
delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.

15 days. Be certain to

INSTALLATION

These food warmers are equipped for the voltage and wattage indicated on the nameplate mounted
to the bottom panel and are designed for use on alternating current (AC) only.

DO NOT CONNECT TO DIRECT CURRENT (DC).
GENERAL OPERATING INSTRUCTIONS

These warmers are designed to use a 3-1/2 quart capacity stainless steel bowl ("SSB") or with 4-1/8
quart insets (SSB-4 or SSB-4H) or a #10 can.

Follow these simple steps for setting up the warmer:

. Fill the warmer bowl with one and a third quarts of hot water.

1

2. Place spacer into bowl.
NOTE: Use 11/16" high spacer for the pump model. Use 1" high spacer (tips up) for SSB-4 or
SSB-4H inset. Use 1" high spacer (tips down) for Polar Ware insets (SSB).

3. Turn warmer on.

4. Place bowl or can with food product into the water bowl.

5. On pump model, pre-heat fudge or cheese before inserting pump.
Pump will not function if fudge or cheese is too thick.

6. Place lid over inset, or close cover on hinged inset, or place pump into fudge or cheese.
After placing pump turn it to engage into the heated spout.

7. Because the consistency of different foods varies, and because liquids and solids absorb heat at
different rates, it is impractical to specify an exact dial setting. However, at the point between

 gures"3"and"4"thetemperatureisapproximately145
 fudge.Whenthedialissetatthegure"5"thetemperatureisapproximately170

holding temperature for cheese sauce. After pre-heating, set the thermostat to the desired
temperature.

8. Turn the control knob to the extreme left position "LOW" when not in use.

9. Do not keep unit on high heat for more than 45 minutes, as the food product may become
overheated.

o

F, the proper holding temperature for

o

F, a good

DO NOT TOUCH THE HEATED SPOUT WITHOUT HEAT INSULATING MITTENS
OR OTHER MEANS OF BURN PREVENTION.

CAUTION

DO NOT OPERATE UNIT WITHOUT WATER. CHECK WATER LEVEL
FREQUENTLY.

6

CAUTION

CLEANING INSTRUCTIONS

IMPORTANT

Stainless steel may corrode if not cleaned properly.
Clean and dry the heated bowl inside the warmer every night. Use a soft cloth and mild soap to keep

exterior surfaces bright and shining. To keep the inside surface of the bowl clean, use steel wool pads
as often as necessary. Do not use detergents, strong abrasives or metal scouring pads on exterior
surface of warmer.

CAUTION

DO NOT IMMERSE IN WATER AT ANY TIME.
PUMP CLEANING

Before using and at least daily, disassemble the pump and wash all parts.
To disassemble pump:

1. Unscrew nut-cylinder. Pull pump-plunger from pump chamber.

2. Unscrew knob from plunger assembly and disassemble.

3. Unscrew cap-tube and nut-sleeve-tube from dispense tube. Remove cover from pump
assembly.

4. Remove pin "U" from pump assembly and disengage dispense tube from pump
chamber.

5. Remove balls from pump chamber.

6. Wash all parts thoroughly in hot soapy water and rinse thoroughly. Use 18" long brush
to clean inside of dispensing tube. Reassemble pump. When reassembling pump, wet
O-ring with edible vegetable oil, then reassemble. Make sure all parts are in their proper
place.

CAUTION

SANITIZING PUMP ASSEMBLIES

It is recommended that the pump assembly be sanitized after routine disassembly and cleaning. Pre­pare a 200 ppm four part solution (similar to Pro-Quat 103). Immerse all pump parts in this solution
for at least 60 seconds, remove and let air dry. Reassemble the pump.

PRIMING PUMP

Three (3) strokes of the pump plunger are necessary to initially prime and vend thick food products.
If pump does not dispense product properly, remove plunger assembly from pump and make sure the

plunger O-ring is in place on the pump plunger. If the O-ring is missing disassemble the pump parts
and make certain the O-ring is not in the pump plunger tube, pump chambers or vend tube before
replacing O-ring.

FAILURE TO DO THIS CAN CAUSE A BROKEN O-RING TO BE PUMPED OUT
WITH THE FOOD BEING VENDED.

SIGN REPLACEMENT

1. Unplug cord from the receptacle.

2. Push front plastic panel up using a plastic pin or very small screwdriver.

3. Pull forward on the bottom edge of the plastic panel and remove it.

4. Replace the sign.

5. Place the front plastic panel back into its original position.

LIGHT BULB REPLACEMENT

1. Unplug cord from the receptacle.

2. Remove both front panels as stated above.

3. Replace bulbs with a 10 or 15 watt candelabra base for 120V or a 10 watt medium base for 240V.

7

2M-4497-2 10/2010

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

ALL:
* Pop-Up Toasters
* Butter Dispensers
* Pretzel Merchandisers

(Model 16PD-A Only)

* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens

(Model PO12 Only)

* Heat Lamps
* Pumps-Manual

Visit our Website at: www.star-mfg.com Email: [e-mail]

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in
which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the
transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of
the unit.

LIMITED EQUIPMENT WARRANTY

All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited
to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair
of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken
to the closest Star service agency, transportation prepaid.

> Star will not assume any responsibility for loss of revenue.
> On all shipments outside the United States and Canada, see International Warranty.
* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
* The warranty period for the Chrome-Max Griddles is ve (5) years on the griddle surface. See detailed warranty provided with unit.
* The warranty period for Teon/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to

Teon/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners, abrasive pads, product identiers and

point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the
“non-stick” properties of such materials.

> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts

and ninety (90) days on labor.

> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or

the Service Center's sub-agency.

> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and

Operating instructions.

> This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted. Labor to replace the part is chargeable to
the customer.

SERVICES NOT COVERED BY WARRANTY

PORTABLE EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair:

1. Travel time and mileage rendered beyond the 50 mile radius limit

2. Mileage and travel time on portable equipment (see below)

3. Labor to replace such items that can be replaced easily during a daily cleaning
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

4. Installation of equipment

5. Damages due to improper installation

6. Damages from abuse or misuse

7. Operated contrary to the Operating and Installation Instructions

8. Cleaning of equipment

9. Seasoning of griddle plates

10. Voltage conversions

11. Gas conversions

12. Pilot light adjustment

13. Miscellaneous adjustments

14. Thermostat calibration and by-pass adjustment

15. Resetting of circuit breakers or safety controls or reset buttons

16. Replacement of bulbs

17. Replacement of fuses

18. Repair of damage created during transit, delivery, &
installation OR created by acts of God

* The Model 510FD Fryer.
* The Model 526TOA Toaster Oven.
* The Model J4R, 4 oz. Popcorn Machine.
* The Model 518CMA & 526CMA Cheese Melter.
* The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.
* The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer.
* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
* All Condiment Dispensers except the Model HPD & SPD Series Dispenser.
* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
* All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.
* All Fast Steamer Models except Direct Connect Series.

8

MP

03-03-93

ADDED VIEW FROM TERMINAL

SIDE OF SWITCH

MP

B 01-12-99

ADDED HIGH LIMIT

THERMOSTAT

MP

-

RELEASED

FOR PRODUCTION

A

02-18-93

10 SUNNEN DRIVE ST. LOUIS, MO 63143

STAR MFG. INTERNATIONAL, INC.

MATERIAL

DR. CK. DATE

FINISH MODEL NO.

TITLE

PART NO.

LIMITS UNLESS OTHERWISE NOTED

FRACTIONS 1/64 DECIMALS .005

CHANGES LTR DATE CHANGE DR

BLACK

GREEN

WHITE

SWITCH

LAMP

LAMP

HEATED SPOUT

ELEMENT

THERMOSTAT

D

A

A

B

D

LEAD IN CORD ASSEMBLY

WIRE ASSEMBLY (2 REQ'D)

HEATING ELEMENT ASSEMBLY

C

B

BLUE

BROWN

GREEN

A

USA NEMA 5-15P

EUROPEAN CEE 7/7

120 V A.C.

230 V A.C.

B

WARMER 3WSA

WARMER 3WLA, LIGHTED

WARMER 3WLA-HS, LIGHTED W/HEATED SPOUT

C

WIRE ASSEMBLY (1 REQ'D)

VIEW FROM TERMINAL

SIDE OF SWITCH

TO CORD SET

A

SEE VIEW BELOW

TO TERMINAL BOARD

HIGH LIMIT

HEATED SPOUT (1 REQ'D)

WIRE ASSEMBLY (1 REQ'D)

F

E

E

F

ON 230V MODELS ONLY

~ ~ 3W- SK1220

WIRING DIAGRAM

5/28/92M.P.

9

MODEL 3WLA-3WSA

3 1/2QT., 4 QT. 120V/240V

STAR MANUFACTURING INTERNATIONAL, INC.

REV. I 08-22-05SK1165

HINGED
BOWL

4 QT (SSB-4H)

OPTIONAL

POWER

TEMP

REFER TO OPERATING INSTRUCTIONS

DO NOT IMMERSE UNIT IN WATER

KEEP DRY WHEN NOT IN USE

CLEAN & CHANGE WATER DAILY

RECOMMENED WATER CAPACITY-1-1/2QT.

Food Warmer

Sign

LIGHTED MODELS

PUMP MODELS

NON-PUMP MODELS

1

4

5

7

8

9

14

17

22

66

24

25

27

29

28

30

31

48

49

50

51

52

53

21

15

26

2

3

6

10

13

11

12

16

18

19

20

PUMP ACCESSORIES

56

57

58

59

(OPTIONAL)

33

32

26

44

46

54

55

47

42

41

45

43

39

35

37

34

38

40

36

61

60

21

21a

MODELS WITH RING & COVER

62

65

64

63

INSET 3.5 QT
(SSB)

67

* = FOR INSETS & LADLES CONTACT DEALER

*

*

*

10

PARTS LIST June 30, 2008, Rev. L

3WLA-3WSA 120V/240V

Key

Number

1 N2-30409 1 CORD ASSY. 120V
1 CORD ASSY. 240V
2 2C-2559 3 10-24 NUT
3 2C-Y5059 4 POP RIVET
4 2I-H7685 4 FOOT
5 N2-Y8542 1 BOTTOM
6 2K-7889 1 BUSHING 90°
7 2E-Y8233 1 TERMINAL BOARD
8 2R-Y8261 1 KNOB-THERMOSTAT
9 2E-Z5884 1 SWITCH
10 2M-Y8248 1 REAR PANEL (SIGN)
11 N2-Y8545 1 FRONT PANEL S.S.
12 2C-1631 1 SCREW #6 x 1/4
13 N2-30424 1 BODY ASSY. (HEATED SPOUT)
N2-30425 1 BODY ASSY. (WARMER)
14 N2-Y8130 1 BAND
15 N2-Y8310 1 PLATE
16 2C-H5569 3 POP RIVET 1/8 x .6
17 2N-Y8227 1 ELEMENT 120V
2N-Y8226 1 ELEMENT 240V
18 2C-Y8312 1 SCREW 8-32 x 1 FH
19 2C-H8670 2 WASHER-LOCK #8
20 2C-2556 2 NUT #8-32
21 2T-Y8262 1 THERMOSTAT
2T-Z0251 1 THERMOSTAT, PRESET (3WSA-HSS ONLY)
21a C3-Y8042 1 THERMOSTAT CLIP (3WSA-HSS ONLY)
22 N2-Y8129 1 BRACKET
23 N2-Y8127 1 BAND-HEATER
24 2A-Y8556 3 SPACER
25 N2-30423 1 BOWL ASSY.
26 N2-30455 1 BOWL SPACER
27 2D-H6295 1 STAINLESS INSET (OPTIONAL)
28 2R-Y5701 1 HANDLE
29 N2-30436 1 COVER
30 2L-Z0577 1 LADLE 1 OZ.
31 N2-30437 1 INSET
32 O2-Y5703 1 HINGE-LEAF
33 2B-Y5792 2 PIN-HINGE
34 2R-Y9854 1 KNOB-BLK.
35 2A-Y9637 1 NUT
36 2L-Y7618 1 COVER
N2-Z0253 1 COVER PUMP (3WSA-HSS ONLY)
37 2V-Y7661 1 PLUNGER-SHIELD
38 2A-Z0718 1 GUIDE
39 2P-Z0830 1 SPRING
40 N2-Y4146 1 WASHER
41 2I-Y9636 1 ROD/PLUNGER
42 2I-Y4143 1 O-RING
43 2P-Y6196 2 BALL-VALVE
44 2A-Y7658 1 NUT
45 2I-Z0730 1 PUMP CHAMBER
46 N2-Y9685 1 PIN-”U”

Part

Number

MODEL

Number

Per

Unit

Description

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

2

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

11

PARTS LIST June 30, 2008, Rev. L

3WLA-3WSA 120V/240V

Key

Number

47 2V-62008 1 DISPENSE TUBE ASSEMBLY STANDARD
2V-62007 1 DISPENSE TUBE ASSEMBLY BUTTER
48 N2-30449 1 SPOUT ASSY. 120V

N2-30427 1 SPOUT ASSY. 240V
NI 2N-Y8557 1 HEATER 15 WT 120V N2-30449, 120V SPOUT ASSY.

49 2E-Y8515 2 LAMP SOCKET 120V
N1-119045 2 LAMP SOCKET 240V
50 N2-30428 1 LAMP SHIELD 120V
N2-30431 1 LAMP SHIELD 240V
51 2S-Y8552 2 LAMP 15W 120V
2S-Y8321 2 LAMP 15W 220V
52 2Q-Y8617 2 PANEL
53 2M-Z0707 6 Packet, Signs Kit
(Kit contains BBQ, Chili, Chili Dog, Fudge and Soup Signs)
2M-Y8497 1 SIGN “BUTTERED”
2M-Z0247 1 SIGN “FREE CHEESE” (3WSA-HSS ONLY)
2M-Z0248 1 SIGN “FREE CHILI” (3WSA-HSS ONLY)
54 2P-Y6108 1 PLUG - CAP
55 2I-Y6110 1 GASKET - CAP
56 N2-Y8763 1 TUBE SPACER 1/4 OZ.
57 N2-Y6123 1 TUBE SPACER 1/2 OZ.
58 N2-Y8764 1 TUBE SPACER 3/4 OZ.
59 2P-Y6211 1 BRUSH
60 2T-Z0250 1 THERMOMETER (3WSA-HSS ONLY)
61 2A-Z0252 1 NUT THERMOMETER (3WSA-HSS ONLY)
62 2R-Z0872 1 KNOB
63 2L-Z0541 1 COVER
64 2C-T1004 1 SCREW
65 2L-Z0540 1 RING
66 2T-Z0622 1 H.L. THERMOSTAT (ON 240V MODELS ONLY)
67 N2-30404 1 PUMP ASSEMBLY COMPLETE

Part

Number

MODEL

Number

Per

Unit

Description

2

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

2

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

12