Stanley FatMax PP1DCS Instruction Manual

132

PROFESSIONAL DIGITAL POWER STATION

INSTRUCTION MANUAL

FUENTE DE ENERGÍA DIGITAL PROFESIONAL

MANUAL DE INSTRUCCIÓN

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.

© 2016 Baccus Global LLC
Boca Raton, FL 33432
[phone]

PP1DCS

English page 3
Español pagina 16

BC

PP1DCS_ManualENSP_072116.indd 32-1 7/27/2016 10:20:05 AM

2

FEATURES
CARACTERÍSTICAS

3

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Este dispositivo cumple con la parte 15 de las normas de la Comisión Federal de Comunicaciones de Estados Unidos (FCC). La operación está
sujeta a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencia perjudicial y (2) este mecanismo debe aceptar cualquier
interferencia recibida, incluida la in-terferencia que puede provocar una operación no deseada.

Este equipo ha sido probado y se encontró que cumple con los límites para dispositivo digital Clase B, según la parte 15 de las normas de la FCC.
Estos límites están diseñados para brindar protección razonable contra interferencia perjudicial en una instalación residencial. Este equipo genera,
usa y puede irradiar energía en frecuencia de radio y, si no se instala y se usa de acuerdo con las instrucciones, puede provocar interferencia
perjudicial en las comunicaciones de radio. Sin embargo, no hay garantía de que la interferencia no ocurra en una instalación en particular. Si el
equipo provoca interferencia perjudicial en la recepción de radio o televisión, lo que se puede determinar al apagar y encender el equipo, el usuario
debe tratar de corregir la interferencia mediante una o más de las siguientes medidas:

•Cambiar la orientación o la ubicación de la antena de recepción.

•Aumentar la separación entre el equipo y el receptor.

•Conectar el equipo a un tomacorriente sobre un circuito diferente de aquel al que está conectado el receptor.

•Consultar al vendedor o pedir la ayuda de un técnico en radio y televisión con experiencia.

Los cambios o las modificaciones no aprobados por el partido responsable de conformidad podían anular la autoridad del usuario para funcionar el
equipo.

FEATURES

1. Handle/roll bar

2. Negative (–) black clamp

3. USB power button

4. Compressor Power Button

5. Compressor Pressure Control Button (+)

6. Backlit LCD screen

7. Battery Status Button

8.

Alternator Check Button

9. Jump Starter Power Switch

10. Area Light Power Button

11. LED Area Light

12. Compressor Pressure Control Button (–)

13. USB ports

14. Built-in 120 volt AC charger (under protective cover)

15. Lower USB Power/Fault Indicators

16. Upper USB Power/Fault Indicators

17. Storage Compartment cover

18. Storage Compartment

19. Nozzle adapter

20. Air hose and SureFit™ nozzle

21. Positive (+) red clamp

CARACTERÍSTICAS

1. Mango / barra antivuelco

2. Pinza negra del negativo (–)

3. Botón de alimentación USB

4. Botón de alimentación del compresor

5. Botón de control de presión del compresor (+)

6. Pantalla del LCD retroiluminada

7. Botón de estado de la batería

8.

Botón de verificación del alternador

9. Interruptor del puente auxiliar de arranque

10. Botón de encendido de la luz de área

11. Luz de área LED

12. Botón de control de presión del compresor (–)

13. Puertos USB

14. Cargador de CA de 120 voltios incorporado (bajo cubierta
protectora)

15. Indicadores inferior de USB potencia / fallo

16. Indicadores superior de USB potencia / fallo

17. Cubierta del compartimiento del almacenaje

18. Compartimiento del almacenaje

19. Adaptador de boquilla

20. Manguera e boquilla de SureFit™

21. Pinza roja del positivo (+)

1

2

3

4

5 7

8

6

91012 1113

15

16

14

21

18

19

20

17

PP1DCS_ManualENSP_072116.indd 2-3 7/27/2016 10:20:06 AM

4 5

SAFETY GUIDELINES / DEFINITIONS

DANGER:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION:

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in

property damage.

RISK OF UNSAFE OPERATION.

When using tools or equipment, basic safety precautions should always be followed to reduce
the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious
injury and property damage. There are certain applications for which tools and equipment are designed. Manufacturer strongly
recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read
and understand all warnings and operating instructions before using any tool or equipment.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating power station. Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

WARNING:

This product or its power cord contains lead, a chemical known to the State of California to cause cancer and

birth defect or other reproductive harm. Wash hands after handling.

•

This unit was designed for household use only.

WARNING: RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS OR PROPERTY

•

Avoid dangerous environments.

Don’t use appliances in damp or wet locations. Don’t use appliances in the rain.

•

Keep children away.

All visitors should be kept at a distance from work area.

•

Dress properly.

Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial,

non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

•

Store idle appliance indoors.

When not in use, appliances should be stored indoors in dry, and high or locked-up place – out

of reach of children.

•

Don’t abuse cord.

Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp

edges.

•

Disconnect appliances.

Disconnect the appliance from the power supply when not in use, before servicing, and when

changing accessories.

•

Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuits or outlets to be used. Receptacles are

available having built in GFCI protection and may be used for this measure of safety.

•

Use of accessories and attachments.

The use of any accessory or attachment not recommended for use with this appliance

could be hazardous. Refer to the accessory section of this manual for further details.

•

Stay alert.

Use common sense. Do not operate this equipment when you are tired or impaired.

•

Check for damaged parts.

Any part that is damaged should be replaced by the manufacturer before further use. Do not use

tool if switch does not turn it on and off. Contact the manufacturer at [phone] for more information.

•

Do not operate this appliance near flammable liquids or in gaseous or explosive atmospheres.

Motors in these tools

normally spark, and the sparks might ignite fumes.

•

Never submerge this unit in water;

do not expose it to rain, snow or use when wet.

•

To reduce risk of electric shock,

disconnect the unit from any power source before attempting maintenance or cleaning.

Turning off controls without disconnecting will not reduce this risk.

•

This equipment employs parts (switches, relays, etc.) that produce arcs or sparks.

Therefore, if used in a garage or enclosed

area, the unit MUST be placed not less than 18 inches above the floor.

SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT

•

IMPORTANT:

This unit is delivered in a partially charged state. Fully charge unit with a household extension cord for a full 40
hours or until the battery status icon shows 4 solid bars before using for the first time. You cannot overcharge the unit using
the AC charging method.

•To recharge this unit, use only the built-in AC charger with an AC extension cord (not included)

•All functions should be turned off when the unit is charging or not in use. Make sure all functions are turned off before

connection to a power source or load.

EXTENSION CORDS:

WARNING:

Use of improper extension cord could result in a risk of fire and electric shock. When using an extension cord,
make sure that the pins of the extension cord are the same number, size and shape as those in the charger; and be sure to use
one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in

DIGITAL LCD SCREEN / PANTALLA DEL LCD DIGITAL

Battery Status Icon

Icono de estado de la

batería

Digital Display (varies by function)

Indicador digital (varía dependiendo

de la función)

Alarm Icon

Icono de alarma

Arrow Icons

Iconos de flecha

Clamp Icons

Iconos de pinza

Battery Voltage Indicator

Indicador del voltaje de

la batería

Compressor Pressure

Indicator

Indicador de presión del

compresor

USB Icon

Icono de USB

Compressor Icon

Icono del compresor

Jump Starter Icon

Icono del puente auxiliar de arranque

Alternator Icon

Icono del

alternador

Alternator Good/Fault

Indicators

Indicadores alternador de

bueno / fallo

Fault Icon

Icono del falla

PP1DCS_ManualENSP_072116.indd 4-5 7/27/2016 10:20:06 AM

76

loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)

240V 0-50 51-100 101-200 201-300
(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)

Ampere Rating Extension Cord Length
More Not more

0’-25’ 26’-50’ 51 ’-100 ’ 101’ -150 ’

Than Than American Wire Gage (AWG)

0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

When an extension cord is used,

make sure that:

• a) the pins of extension cord are the same number, size and shape as those in the charger,

• b) the extension cord is properly wired and in good electrical condition,

• c) the wire size is large enough for the AC rating of the charger.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

Pull the extension cord by the plug rather than the cord

when disconnecting from the built-in 120 volt AC charger or the AC outlet.

SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS

WARNING: BURST HAZARD

Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst
and cause injury to persons and damage property. Use the unit for charging/boosting a lead-acid battery only. It is not intended
to supply power to a low-voltage electrical system other than in a starter-motor application.

•Use of an attachment not supplied, recommended or sold by manufacturer specifically for use with this unit may result in a
risk of electrical shock and injury to persons.

WARNING: RISK OF EXPLOSIVE GASES

•Working in the vicinity of a lead acid battery is dangerous. Batteries generate explosive gases during normal battery
operation. For this reason, it is of the utmost importance that each time before using the jump-starter you read this manual
and follow instructions exactly.

•To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and
manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary markings on these products
and on the engine.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

•NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.

•Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting,

read the vehicle’s owner’s manual to confirm that external-starting assistance is suitable.

•When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.

•Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns.

Be aware of first aid procedures in case of accidental contact with battery acid.

•Have plenty of fresh water and soap nearby in case battery acid contacts skin.

•Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station

•Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

•Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid battery. A

lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin, causing a
severe burn.

•Do not wear vinyl clothing when jump-starting a vehicle. Friction can cause dangerous static-electrical sparks.

•Be extra careful to avoid dropping a metal tool onto the battery. It might spark or short-circuit the battery or another

electrical part and could cause an explosion.

•Jump-start procedures should only be performed in a safe, dry, well-ventilated area.

•Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangerous sparks, power

arcing and/or explosion.

•When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all
clamps, cords, clothing and body parts away from moving vehicle parts.

•Never allow red and black clamps to touch each other or another common metal conductor — this could cause damage to the
unit and/or create a sparking/explosion hazard.

•Make sure to connect the clamps with correct polarity. Damage caused by improper connection is not covered by the
Warranty.

•Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals
with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).

•Place this unit as far away from the battery as cables permit.

•Never allow battery acid to come in contact with this unit.

•Do not operate this unit in a closed area or restrict ventilation in any way.

•This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt

battery system.

•This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does
not have a battery installed.

•Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of
attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.

•Do not use this jump starter on a watercraft. It is not qualified for marine applications.

•Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and

recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/
or moisture.

SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS

WARNING: BURST HAZARD: Bursting articles can cause serious injury.

•Carefully follow instructions on articles to be inflated.

•Never exceed the recommended pressure listed in instructions on articles to be inflated. If no pressure is given, contact article

manufacturer before inflating.

•Always monitor the pressure on the LCD screen.

CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:

•Never leave the compressor unattended while in use.

•Do not operate compressor continuously for longer than approximately 10 minutes, depending on ambient temperatures. This

could damage the compressor. Follow the instructions in the "Portable Compressor" section.

SPECIFIC SAFETY INSTRUCTIONS FOR THE USB POWER PORTS

•Do not insert foreign objects into the USB Power Ports.

•Do not attach USB hubs or more than one personal electronic device to each USB Power Port.

•Do not use this unit to operate appliances that require more than 6.2 amps in total to operate from the USB power ports

FIRST AID

•

Skin:

If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If

redness, pain, or irritation occurs, seek immediate medical attention.

•

Eyes:

If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate

medical attention.

•

LCD liquid crystal display:

If liquid crystal comes in contact with your skin: Wash area off completely with plenty of water.
Remove contaminated clothing. If liquid crystal gets into your eye: Flush the affected eye with clean water and then seek
medical attention. If liquid crystal is swallowed: Flush your mouth thoroughly with water. Drink large quantities of water and
induce vomiting. Then seek medical attention.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Congratulations on purchasing your new

Stanley® FatMax® Professional Digital Power Station. Read this Instruction Manual and

follow the instructions carefully before using this unit.

PP1DCS_ManualENSP_072116.indd 6-7 7/27/2016 10:20:07 AM

8 9

OVERVIEW

Common Actions and Unit Responses

The following actions turn the unit on and activate the LCD screen:

Press the Battery Status Button.

(Refer to the "Viewing Battery Status"
section.)

A beep will sound and the backlit LCD screen will display the Battery Status
Icon and Battery Voltage Indicator for 10 seconds before the unit automatically
turns off.

Press the Alternator Check Button.

(Refer to the "Alternator Check"
section.)

A beep will sound and the backlit LCD screen will display the Battery Status
Icon, and the Alternator Icon will flash. The unit remains on until the Alternator
Check Button is pressed again to turn it off.

Press the LED Area Light Power Button.

(Refer to the "LED Area Light" section.)

A beep will sound and the Area Light will turn on. The backlight will turn on for
10 seconds (only). The LCD screen will continue to display the Battery Status
Icon and Battery Voltage Indicator. The unit remains on until the LED Area Light
Power Button is pressed again to turn it off.

Press the USB Power Button.

(Refer to

the "USB Ports" section.)

A beep will sound and the backlit LCD screen will display the Battery Status
Icon and Battery Voltage Indicator, as well as the USB Icon, indicating the 4 USB
Ports are available. The unit remains on until the USB Power Button is pressed
again to turn it off.

Press the Compressor Power Button.

(Refer to the "Portable Compressor"
section.)

A beep will sound and the backlit LCD screen will display the Battery Status
Icon, "XXX" PSI and the Compressor Icon. If no further actions are taken after
1 minute, the unit will display the Battery Status Icon and Battery Voltage
Indicator for 10 seconds before automatically turning off.

Whenever the clamps are properly
connected to a battery

(refer to the

"Jump Starter" section)

…

… a beep will sound and the backlit LCD screen will display the Battery Status
Icon, Battery Voltage Indicator, the Clamp Icons, and the “+” and”–” signs, as
well as the flashing Jump Starter Icon. The unit remains on until the clamps are
disconnected from the battery.

If the Jump Starter Power Switch is
rotated to the on position and the
clamps are not connected to a battery

(refer to the "Jump Starter" section)

…

... a two-second warning will sound every 10 seconds. The backlit LCD screen will
display the Battery Status Icon, Battery Voltage Indicator, the Clamp Icons, and
the “+” and ”–” signs. The Alarm Icon and the Jump Starter Icon will flash. The
unit remains on until the Jump Starter Power Switch is switched off and then
displays the battery status icon and the voltage of digital display for 10 seconds
before automatic shut down.

If the clamp connections to the
battery’s positive and negative
terminals are reversed

(refer to the

"Jump Starter" section)

…

… the backlit LCD screen will display the Battery Status Icon, Battery Voltage
Indicator, and the Clamp Icons. The Alarm Icon, the “+” and ”–” signs and the
Arrow Icons will flash and the unit will sound a warning continuously until the
clamps are disconnected from the battery.

When the unit is charging or
recharging using the built-in 120 Volt
AC Charger

(refer to the "Charging/

Recharging" section)

…

… a beep will sound and the backlight will turn on for 10 seconds (only). The
LCD screen will continue to display the Battery Status Icon and Battery Voltage
Indicator. The bars on the Battery Status Icon will change from empty to solid
(bottom to top) repeatedly.

Note: The unit will automatically power off once ALL the functions are turned off.

VIEWING BATTERY STATUS

To check the unit’s battery charge level, press the Battery Status Button. The Battery Status Icon and Battery Voltage Indicator
will display for 10 seconds (only), indicating the battery charge level as follows.

•If the battery charge level is at full capacity, four solid bars will display.

•If the battery is partially charged, two or three solid bars will display.

•If the battery is nearly empty, one solid bar will display. The unit should be charged at this time.

•If the battery is completely empty, four blank bars will display. The unit MUST be charged at this time or the unit’s built-in

low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut
down. The unit will not operate until the battery is recharged.

Note: If no other actions are taken, the unit will automatically power off after 10 seconds.

CHARGING/RECHARGING

Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self-
discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost
through self-discharge. When the unit is not in frequent use, manufacturer recommends the battery should be recharged at least every
30 days and after each use.

Notes: This unit is delivered in a partially charged state – you must fully charge it before using it for the first time. Initial AC charge should be for 40 hours or

until the Battery Status Icon shows 4 solid bars.
Recharging the battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life.
The battery can be recharged using the built-in 120 Volt AC Charger.
Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.

CAUTION: RISK OF PROPERTY DAMAGE:

Failure to keep the battery charged will cause permanent damage and result in

poor jump starting performance.

IMPORTANT:

If you know the unit is discharged, but the battery icon displays four solid bars as if the unit is fully charged when
connected to a charging power source, this may be due to the internal battery having high impedance. The manufacturer
suggests leaving the unit charging for a period of 40 hours using the built-in AC charger before use.

Charging/Recharging Using the Built-In 120 Volt AC Charger and AC Extension Cord

1. Lift the protective cover of the built-in 120 volt AC charger located on the lower left front of the unit (refer to the

"Features" section to locate). Connect an extension cord to the unit. Plug the other end of the cord into a standard 120-volt
AC wall outlet. When the unit is properly connected to an AC power source, the LCD screen will display the following:

The bars on the Battery Status Icon represent the charge level of the unit’s internal battery. The bars on the Battery Status

Icon will change from empty to solid (bottom to top) repeatedly to indicate the unit is charging. The backlight will turn on
for 10 seconds (only).

2. Charge for approximately 40 hours or until the Battery Status Icon shows 4 solid bars.

3. When charging is complete, unplug the AC extension cord from the AC outlet and then disconnect it from the unit.

JUMP-STARTER

This unit is equipped with a jump starter power switch that allows energy to flow only when proper connections are made to
battery and frame.

a) For negative-grounded systems, connect the positive (red) clamp to the positive ungrounded battery post and the negative

(black) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel
lines or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block.

b) For positive-grounded systems, connect the negative (black) clamp to the negative ungrounded battery post and the

positive (red) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the
carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block.

IMPORTANT:

Make sure the Compressor Power Button has been turned off before attempting to use the unit as a Jump Starter.

WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

•

FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE “Specific safety instructions for jump starters” section of this
instruction manual.

•Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or explosion.

•If the clamps are connected incorrectly with regard to polarity, the unit will sound a continuous alarm until the clamps are

disconnected. The backlit LCD Screen will display the Battery Status Icon, the Battery Voltage Icon and the Clamp Icons. The

PP1DCS_ManualENSP_072116.indd 8-9 7/27/2016 10:20:07 AM