Stanley Black and Decker SPL10000M User Manual
SPL10000M
Operation and
Maintenance Manual
GET IT ON
SPL10000M
WARNING
To reduce the risk of injury, read and understand these safety warnings and
instructions before using the light. Keep these instructions with the light
for future reference. If you have any questions, contact your MAC TOOLS
representative or distributor.
10,000LM AREA LIGHT WITH BLUETOOTH CONTROL
© 2017 Mac Tools
INTRODUCTION
SPL10000M is a professional-grade, hands-free area light. This light will deliver efficient, dependable
service when used correctly and with care. As with any fine light, for best performance, the manufacturer’s
instructions must be followed. Please study this manual before operating the light, and understand the
safety warnings and instructions. The instructions on operation and maintenance should be read carefully,
and the manual kept for reference.
NOTE: Additional safety measures may be required because of your particular application of the light. Contact
your Mac Tools representative or distributor with any questions concerning the light and its use.
LIMITED WARRANTY
We warrant that this light shall be free from manufacturing defects for a period of ONE YEAR from the original
purchase date. Our obligation to the original purchaser shall be limited to repairing or replacing, at our expense
(not including shipping charges) a defective light if returned by the original purchaser within one year from
the date of purchase, all incoming shipping charges prepaid. THIS WARRANTY DOES NOT COVER DEFECTS OR
DAMAGES TO THE LIGHT (i) after the warranty period expires; (ii) resulting from misuse or abnormal operation;
(iii) resulting from a failure to properly maintain or operate the tool; or (iv) resulting from any repair or maintenance services performed by any party other than Mac Tools.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
MPE REQUIREMENTS
To satisfy FCC / IC RF exposure requirements, a separation distance of 8 inches (20 cm) or more should be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
MACTOOLS.COM
2
SPECIFICATIONS
HANDLES FOR
EASY CARRYING
FOAMED
POLYURETHANE
BUMPER
MOUNTING FOR
TRIPOD STAND
MAGNET BASE WITH
ANTI-SLIP RUBBER PAD
COB LED
SWITCH BUTTON
180° ROTATING
BRACKET
SPECIFICATIONS
Model # Lumen Lux @1m
SPL10000M
Magnet
Yes
Step1
2000
Cable
5M 18/3
SJTOW
Step2
4000
Step3
6000
Dust and Water Resistance for Dimmer Control
Step4
8000
IP67
Step5
10000
Step1
750
IK level
Step2
Step3
1500 2250 3000
800.MACTOOLS
YesIK07
Step4
Step5
3800
3
GETTING STARTED
To use, plug the unit into any 120V AC power source, such as a wall receptacle.
•
Press the button" "to turn the light on and off. Press button " " or " " to adjust light output.
•
Long press on button " " goes to 10,000lm mode. Long press on putton " " goes to 2,000lm
mode.
Bluetooth control the light on/off or adjust the light output.
•
• One Bluetooth device can connect up to five (5) lights.
BLUETOOTH CONNECTION
Using Your SPL10000M with
If you have a SPL10000M, you can use its capability to pair it with the Mac Tools Lighting
application on your smartphone or tablet, and then operate your light remotely.
• From either the or , download the Mac Tools Lighting application to your smart
phone or tablet.
GET IT ON
• Using the Mac Tools Lighting application, select the tab.
• Any available Mac Tools lights will appear on this screen
o Press to connect the light to .
o Press to change the name of the light
(
optional)
.
• Select the tab to control up to 5 Mac Tools lights.
o Only connected lights will appear on this screen.
• Press to turn the light on.
o Icon will turn green when light is powered on.
• Press on the output or adjust the slider bar to choose light output.
®
THE BLUETOOTH
TOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY MAC TOOLS. IS UNDER LICENSE. OTHER TRADEMARKS AND TRADE NAMES ARE THOSE OF THEIR RESPECTIVE OWNERS.
4
WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED BY BLUE-
MACTOOLS.COM
WARNINGS
• Do not use in or around water
• Use only the recommended voltage and frequency requirements
• Keep out of the reach of children
• Do not operate light with wet hands
• Keep lamp away from hot objects
• Do not incinerate
• Do not crush
CUSTOMER SERVICE
We at Mac Tools are committed to our customers, please reference the following phone number for a direct
contact to one of our customer technicians. They will be more than happy to help with any service or warranty questions you may have about your professional area light.
Mac Tools
505 North Cleveland Avenue
Westerville, Ohio 43082
800.MACTOOLS
MACTOOLS.COM
800.MACTOOLS
5
Loading...