Stanley TLM330 User Manual

Table of Contents

EN

Instrument Set-up- - - - - - - - - - - - - - - - - - - - - - -2

Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2
Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - -3

Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4

Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - -4
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Adjusting measuring reference / tripod - - - - - - - - - - -4
Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - -5
Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - -5
Tilt unit setting- - - - - - - - - - - - - - - - - - - - - - - - - - - - -5
Timer (automatic release) - - - - - - - - - - - - - - - - - - - -5
Beep ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Illumination ON/OFF - - - - - - - - - - - - - - - - - - - - - - - -6
Keypad lock ON - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Keypad lock OFF - - - - - - - - - - - - - - - - - - - - - - - - - -6

Measuring Functions - - - - - - - - - - - - - - - - - - -7

Measuring single distance - - - - - - - - - - - - - - - - - - - - 7
Permament / Minimum-Maximum measuring - - - - - - -7
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7
Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -8
Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -9
Triangular area - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - 11
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - 11
Pythagoras (partial height) - - - - - - - - - - - - - - - - - - - 12
Leveling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - 14

Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - -14
Memory (20 last displays) - - - - - - - - - - - - - - - - - - - -15
Delete Memory - - - - - - - - - - - - - - - - - - - - - - - - - - -15

Calibration - - - - - - - - - - - - - - - - - - - - - - - - - - - - -16

Calibration of tilt sensor (Tilt Calibration) - - - - - - - - -16

Technical Data - - - - - - - - - - - - - - - - - - - - - - - - -17

Message Codes - - - - - - - - - - - - - - - - - - - - - - - -18

Care - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18

Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18

Safety Instructions - - - - - - - - - - - - - - - - - - - - -18

Areas of responsibility - - - - - - - - - - - - - - - - - - - - - -18
Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Electromagnetic Compatibility (EMC) - - - - - - - - - - - -19
FCC statement (applicable in U.S.) - - - - - - - - - - - - -20
Laser classification- - - - - - - - - - - - - - - - - - - - - - - - -20
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -20

Stanley TLM330

1

EN

Display

On / Measure

Measuring

reference

Add

Units /
Memory

Pythagoras

Height
Tracking

Subtract

Clear / Off

Area /

Volume

Triangle Area

Inclination /
Stake out

Smart Hori­zontal Mode

Timer

Instrument Set-up

Introduction

The safety instructions and the user manual should be
read through carefully before the product is used for the
first time.

The person responsible for the product must ensure that
all users understand these directions and adhere to them.

The symbols used have the following meanings:

WARNING

Indicates a potentially hazardous situation or an unintended use
which, if not avoided, will result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation or an unintended use
which, if not avoided, may result in minor injury and/or appreci­able material, financial and environmental damage.

Important paragraphs which must be adhered to in practice

i

as they enable the product to be used in a technically
correct and efficient manner.

Overview

2

Stanley TLM330

Instrument Set-up

Area /

Volume

Units

Stake out

Indirect height

Circumfer-

ence

Measuring

reference

2nd result

Battery

Angle

Wall area

Addition /

Subtraction

Timer

Memory

Pythagoras

Horizontal
measurement

Min/Max
Measuring

Main line

i

To ensure a relia­ble use, do not
use zinc-carbon
batteries.
Change batteries
when battery
symbol is flash­ing.

EN

Display

Insert batteries

Stanley TLM330

3

EN

2 sec

Device is
turned OFF.

Press ON but­ton 2 sec to
start continuous
laser mode. If
no key is
pressed for 180
sec, the device
switches off au­tomatically.

1x

Undo last action.

2x

Leave actual
function, go to de­fault operation
mode.

If the info icon appears with a
number, observe the instruc­tions in section "Message
Codes".
Example:

Distance is measured from the
front of the device.

1

Distance is measured
from the tripod thread
permanently.

2

Distance is measured from the rear
of the device (standard setting).

3

Operations

Switching ON/OFF Clear Message Codes

i

Adjusting measuring reference / tripod

4

Stanley TLM330

Operations

The orientation
of the endpiece
is automatically
detected and
the zero point is
accordingly ad­justed.

0.000 m

0.0000 m

0.00 m

0.00 ft
0'00" 1/32

0.00 in
0 in 1/32

Switch between the
following units:

2 sec

0.0 °

0.0 %

Switch between the
following units:

2 sec

simultaneously

s

1

Adjust delay of au­tomatic release
(max. 60 sec,
standard setting
5sec)

2

Once the key is released with the la­ser activated, the remaining seconds
until the measurement are displayed
in a countdown. The delayed release
is recommended for precise aiming
e.g. at long distances. It avoids shak­ing of the device when pressing the
measurement key.

Multifunctional endpiece

Distance unit setting Tilt unit setting

Timer (automatic release)

EN

i

i

Stanley TLM330

5

EN

2 sec

simultaneously

2 sec

simultaneously

2 sec

simultaneously

PRESS

MINUS

1

within

2 sec

2

Operations

Beep ON/OFF Illumination ON/OFF

Keypad lock ON Keypad lock OFF

6

Stanley TLM330

Measuring Functions

1

Aim active laser at target.

2

8.532 m

3

Target surfaces: Measuring
errors can occur when meas­uring to colourless liquids,
glass, styrofoam or semi-per­meable surfaces or when
aiming at high gloss surfac­es. Against dark surfaces the
measuring time increases.

1

2 sec

8.532 m

Used to measure room diagonals (maximum val­ues) or horizontal distance (minimum values)

The minimum and maximum dis­tance measured is displayed
(min, max.). The last value meas­ured is displayed in the main line.

min. max.

2

Stops permanent / minimum­maximum measuring.

3

7.332 m

1

The next meas­urement is added
to the previous
one.

2

The next meas­urement is sub­tracted from the
previous one.

5.5I5 m

I2.847 m

3

The result is shown in the
main line and the measured
value above. This process
can be repeated as required.
The same process can be
used for adding or subtracting
areas or volumes.

Measuring single distance

Permament / Minimum-Maximum measuring

Add / Subtract

EN

i

Stanley TLM330

i

7

EN

11x2

Aim laser at first
target point.

3

4

Aim laser at sec­ond target point.

24.352 m

2

5

The result is shown in the
main line and the measured
value above.

19.823 m

24.352 m

2

2 sec

Circumference

Area

6

Measuring Functions

Area

i

8

Stanley TLM330

Measuring Functions

12x2

Aim laser at first
target point.

3

4

Aim laser at sec­ond target point.

5

6

Aim laser at third
target point.

78.694 m

3

7

i

The result is
shown in the
main line and
the measured
value above.

208.703 m

2

80.208 m

78.694 m

3

2 sec

Circumference

Wall areas

Volume

8

Volume

EN

Stanley TLM330

9

EN

1

2

Aim laser at first
target point.

3

4

Aim laser at sec­ond target point.

5

6

Aim laser at third
target point.

24.352 m

2

7

33.852 m

24.352 m

2

40.8 °

2 sec

Angle included by the first
two measurements

Circumference

Triangular area

8

Measuring Functions

Triangular area

10

Stanley TLM330

Measuring Functions

11x2

Aim laser at up­per point.

3

4

Aim laser rectan­gular at lower
point.

8.294 m

5

i

The result is shown
in the main line and
the measured dis­tance above.

Pressing the meas­uring key for 2 sec
in the function acti­vates automatically
Minimum or Maxi­mum measure­ment.

12x2

Aim laser at up­per point.

3

4

Aim laser at rec­tangular point.

5

6

Aim laser at lower point.

8.294 m

7

The result is shown in the main
line and the measured distance
above.
Pressing the measuring key for
2 sec in the function activates
automatically Minimum or Maxi­mum measurement.

Pythagoras (2-point)

Pythagoras (3-point)

EN

i

Stanley TLM330

11

EN

13x2

Aim laser at up­per point.

3

4

Aim laser at 2nd
point.

5

6

Aim laser at rec­tangular point.

2.602 m

7

i

The result is shown in the main
line and the measured distance
above.
Pressing the measuring key for 2
sec in the function activates auto­matically Minimum or Maximum
measurement.

Measuring Functions

Pythagoras (partial height)

12

Stanley TLM330

Measuring Functions

i

This function displays continously
the inclination of the device. From
an inclination of ±5° the device
starts beeping frequently. The
more it gets to 0° the faster it
beeps. If an inclination of ±0.3° is
reached the device beeps continu­ously.

1

1x

Place device on object to be levelled.

2

8.7 °

The inclina­tion is dis­played
(Range
±180°).

1

2

3

1.000 m

1

2x

0.625 m

2

Adjust
value.

3

Approve value and
start measurement.

4

Move device
slowly along the
stake-out line.
The distance to
the next stake
out point is dis­played.

0.625 m

0.240 m

0.240 m is missing
up to next 0.625 m
distance.

When approaching a stake
out point to less than 0.1 m
the instrument starts to
beep.
The function can be stopped
by pressing the CLEAR/OFF
button.

Leveling

Stake out

EN

Stanley TLM330

i

13

EN

1

Aim laser at tar­get.

2

0.032 m

24.3 °

4.827 m

α

z

y

z

y

3

(up to 360° and a transverse
tilt of ±10°)

i

Press key
again to
switch off
horizontal
measure­ment.

i

This function displays continous­ly the tracking height if the device
is turned on a tripod. No 2nd dis­tance measuring is needed as
only the angle is automatically
measured.

1

x

x

Aim laser at lower
point.

2

3

h1

h2

h3

Aim laser at upper points and
angle/ height tracking starts au­tomatically.

4

h1

h2

h3

x

y

30.2 °

6.932 m

9.827 m

x

y

5

= Tracking height if de­vice is turned on tripod

= Tracking angle

i

The tracked
height "y" is in
90° to the 1st
aimed point
"x".

6

Stops Height tracking and
displays last measurement.

Measuring Functions

Smart Horizontal Mode

Height tracking

14

Stanley TLM330

Measuring Functions

8.294 m

20

20 last displays
are displayed.

1

8.294 m

20

Navigates trough
20 last displays.

2

The value from
the main line can
be used for fur­ther calculations.

2 sec

3

2 sec

simultaneously

Memory is completely de­leted.

Memory (20 last displays) Delete Memory

EN

Stanley TLM330

15

EN

1

2 sec

simultane-

ously

2

Place device on absolutely flat surface.

3

180°

4

Turn the device horizontally by 180°
and place it again on absolutely flat sur­face.

5

6

Turn the device upside down and place it again on
absolutely flat surface.

7

180°

8

Turn the device horizontally by 180°
and place it again on absolutely flat
surface.

9

i

After 2 sec
the device
goes back
to the nor­mal mode.

Calibration

Calibration of tilt sensor (Tilt Calibration)

16

Stanley TLM330

Technical Data

Distance measurement

Typical Measuring Tolerance* ± 1.0 mm / 0.04 in ***

Maximum Measuring Toler­ance**

Range of target plate 100 m / 330 ft

Typical Range* 80 m / 262 ft

Range at unfavourable condi­tion ****

Smallest unit displayed 0.1 mm / 1/32 in

Ø laser point
at distances

Tilt measurement

Measuring tolerance to laser
beam*****

Measuring tolerance to
housing*****

Range 360°

General

Laser class 2

Laser type 635 nm, < 1 mW

Protection class IP54 (dust- and splash

Autom. laser switch off after 90 s

Autom. power switch-off after 180 s

Battery durability (2 x AAA) up to 5000 measure-

Dimension (H x D x W) 115.6 x 58 x 32 mm

Weight (with batteries) 155 g / 4.98 oz

Temperature range:

- Storage

- Operation

± 2.0 mm / 0.08 in ***

60 m / 197 ft

6 /30 / 60 mm
(10 / 50 / 100 m)

± 0.2°

± 0.2°

water protected)

ments

4.55 x 2.28 x 1.26 in

-25 to 70 °C

-13 to 158 °F

-10 to 50 °C
14 to 122 °F

* applies for 100 % target reflectivity (white painted
wall), low background illumination, 25 ºC

** applies for 10 to 500 % target reflectivity, high back­ground illumination, - 10 ºC to + 50 ºC

*** Tolerances apply from 0.05 m to 10 m with a confi­dence level of 95%. The maximum tolerance may
deteriorate to 0.1 mm/m between 10 m to 30 m and to

0.2 mm/m for distances above 30 m
**** applies for 100 % target reflectivity, background

illumination of approximately 30'000 lux
***** after user calibration. Additional angle related

deviation of +/- 0.01° per degree up to +/-45° in each
quadrant. Applies at room temperature. For the whole
operating temperature range the maximum deviation
increases by +/- 0.1°.

For accurate indirect results, the use

i

of a tripod is recommended. For
accurate tilt measurements a trans­verse tilt should be avoided.

Functions

Distance measuring yes

Min/Max measuring yes

Permanent measuring yes

Stake-out yes

Addition/Subtraction yes

Area yes

Volume yes

Triangular area yes

Pythagoras 2-point, 3-point,

Smart Horizontal Mode /
Indirect height

Height tracking yes

Levelling yes

Memory 20 displays

Beep yes

Illuminated display yes

Multifunctional endpiece yes

partial height

yes

EN

Stanley TLM330

17

EN

Message Codes

If the message Error does not disappear
after switching on the device repeatedly,
contact the dealer.

If the message InFo appears with a
number, press the Clear button and
observe the following instructions:

No. Cause Correction

156 Transverse tilt

greater than 10°

162 Calibration mistake Make sure, the device

204 Calculation error Perform measurement

252 Temperature too

high

253 Temperature too

low

255 Received signal too

weak, measuring
time too long

256 Received signal too

high

257 Too much back-

ground light

258 Measurement

outside of meas­uring range

260 Laser beam inter-

rupted

Hold the instrument
without any transverse
tilt.

is placed on a abso­lutely horizontal and flat
surface. Repeat the
calibration procedure. If
the mistake still occurs,
contact your dealer.

again.

Let device cool down.

Warm device up.

Change target surface
(e.g. white paper).

Change target surface
(e.g. white paper).

Shadow target area.

Correct range.

Repeat measurement.

Care

• Clean the device with a damp, soft cloth.

• Never immerse the device in water.

• Never use aggressive cleaning agents

or solvents.

Warranty

The Stanley TLM has a two-year warranty.
For further information on this, contact
your dealer.
Subject to change (drawings, descriptions

and technical data).

Safety Instructions

The person responsible for the instrument
must ensure that all users understand
these directions and adhere to them.

Areas of responsibility

Responsibilities of the manufacturer
of the original equipment:

Stanley Tools
701 E. Joppa Road
Towson, Maryland 21286

www.STANLEYLASERS.com
www.STANLEYTOOLS.com
www.STANLEYTOOLS.eu

The company above is responsible for
supplying the product, including the User
Manual in a completely safe condition.

The company above is not responsible for
third party accessories.

Responsibilities of the person in
charge of the instrument:

• To understand the safety instructions on
the product and the instructions in the
User Manual.

• To be familiar with local safety regula­tions relating to accident prevention.

• Always prevent access to the product by
unauthorised personnel.

18

Stanley TLM330

Safety Instructions

EN

Permitted use

• Measuring distances

• Tilt measurement

Prohibited use

• Using the product without instruction

• Using outside the stated limits

• Deactivation of safety systems and

removal of explanatory and hazard
labels

• Opening of the equipment by using tools
(screwdrivers, etc.)

• Carrying out modification or conversion
of the product

• Use of accessories from other manufac­turers without express approval

• Deliberate dazzling of third parties; also
in the dark

• Inadequate safeguards at the surveying
site (e.g. when measuring on roads,
construction sites, etc.)

• Deliberate or irresponsible behaviour on
scaffolding, when using ladders, when
measuring near machines which are
running or near parts of machines or
installations which are unprotected

• Aiming directly in the sun

Hazards in use

WARNING

Watch out for erroneous measurements if
the instrument is defective or if it has been
dropped or has been misused or modified.
Carry out periodic test measurements.

Particularly after the instrument has been
subject to abnormal use, and before,
during and after important measurements.

CAUTION

Never attempt to repair the product your­self. In case of damage, contact a local
dealer.

WARNING

Changes or modifications not expressly
approved could void the user’s authority to
operate the equipment.

Limits of use

Refer to section "Technical data".

i

The device is designed for use in

areas permanently habitable by
humans. Do not use the product in explo­sion hazardous areas or in aggressive
environments.

Disposal

CAUTION

Flat batteries must not be disposed of with
household waste. Care for the environ­ment and take them to the collection points
provided in accordance with national or
local regulations.

The product must not be disposed with
household waste.

Dispose of the product appropri­ately in accordance with the
national regulations in force in your
country.

Adhere to the national and country specific
regulations.

Product specific treatment and waste
management can be downloaded from our
homepage.

Electromagnetic Compatibility
(EMC)

WARNING

The device conforms to the most stringent
requirements of the relevant standards
and regulations.

Yet, the possibility of causing interference
in other devices cannot be totally
excluded.

Stanley TLM330

19

EN

Laser Radiation

Do not stare into the beam

Laser class 2

acc. IEC 60825-1:2007
Maximum radiant power: <1mW
Emitted wavelength: 620-690nm

Beam divergence: 0.16 x 0.6 mrad

Impulse duration: 0.2 x 10

-9

s - 0.8 x 10-9s

Safety Instructions

FCC statement (applicable in U.S.)

This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential instal­lation.This equipment generates, uses and
can radiate radio frequency energy and, if
not installed and used in accordance with
the instructions, may cause harmful inter­ference to radio communications.

However, there is no guarantee that inter­ference will not occur in a particular instal­lation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the interfer­ence by one or more of the following
measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced
radio/TV technician for help.

Laser classification

The device produces visible laser beams,
which are emitted from the instrument:
It is a Class 2 laser product in accordance
with:

• IEC60825-1 : 2007 „Radiation safety of
laser products“

Laser Class 2 products:

Do not stare into the laser beam or direct it
towards other people unnecessarily. Eye
protection is normally afforded by aversion
responses including the blink reflex.

WARNING

Looking directly into the beam with optical
aids (e.g. binoculars, telescopes) can be
hazardous.

CAUTION

Looking into the laser beam may be
hazardous to the eyes.

Labelling

a

Attach the laser sticker (a) of your country
language.

20

Stanley TLM330