Stanley STSP125 Original Instructions Manual

STSP125

English Page 3

2

FIG. A

FIG. C

FIG. D

FIG. F

FIG. E

6

7

9

FIG. B

2

6

4

1

11

2

3

5

7

9

10

With wet kit
Blade not included

10

9

8

ENGLISH (Original instructions)

3

DO NOT RETURN THIS PRODUCT TO THE STORE,

first contact your local STANLEY Office

or nearest authorized service center.

General Safety Rules

Warning! Read and understand all instructions.

Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious

personal injury.

Save These Instructions

Safety Instructions

General power tool safety warnings.

Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.

1. Work Area Safety

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical Safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk
of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of
electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric
shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of

electric shock.

Note: The term “Residual Curent Device (RCD)” can be
replaced by “Ground Fault Circuit Interrupter (GFCI)” or by
“Earth Leakage Circuit Breaker (ELCB)”.

3. Personal Safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not
use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on
invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal
injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are
connected and properly used. Use of these devices

can reduce dust related hazards.

(Original instructions) ENGLISH

4

4. Power Tool Use and Care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was
designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained
users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations

different from those intended could result in a hazardous
situation

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.

Safety Instructions For Abrasive Cuttingoff
Operations Cut-off Machine Safety Warnings

a) The guard provided with the tool must be securely

attached to the power tool and positioned for

maximum safety, so the least amount of wheel is
exposed towards the operator. Position yourself and
bystanders away from the plane of the rotating
wheel. The guard helps to protect operator from broken

wheel fragments and accidental contact with wheel.

b) Use only diamond cut-off wheels for your power

tool. Just because an accessory can be attached to your

power tool, it does not assure safe operation.

c) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed

can break and fly apart.

d) Wheels must be used only for recommended

applications. For example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these
wheels may cause them to shatter.

e) Always use undamaged wheel flanges that are of

correct diameter for your selected wheel. Proper
wheel flanges support the wheel thus reducing the
possibility of wheel breakage.

f) Do not use worn down reinforced wheels from larger

power tools. Wheels intended for a larger power tool are

not suitable for the higher speed of a smaller tool and
may burst.

Note: The above warning does not apply for tools only
designated to be used with diamond wheels.

g) The outside diameter and the thickness of your

accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

h) The arbour size of wheels and flanges must properly

fit the spindle of the power tool. Wheels and flanges

with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.

i) Do not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If power
tool or wheel is dropped, inspect for damage or
install an undamaged wheel. After inspecting and
installing the wheel, position yourself and
bystanders away from the plane of the rotating wheel
and run the power tool at maximum no load speed

ENGLISH (Original instructions)