Stanley STSM1510-B9 User manual

STSM1510

English Page 5 Russian Page 18 Ukrainian Page 33

ENGLISH

(Original instructions)

FIG. 1

FIG. 2

Parts Description (Fig. 1 )

FIG. 1 1. Operating Handle

2. Guard

3. Saw Blade

4. Miter Clamp Handle

5. Miter Latch

6. Miter Scale

7. Left Side Fence

8. Bench Mounting Hole

9. Dust Spout

Parts Description (Fig. 2 )

FIG. 2 10.Lock Down Pin

11.Hand Indentation

12.Right Side Fence

13.Kerf Plate

14.Motor Housing

15.Spindle Lock Button

16.Trigger Switch

17.Bevel Clamp Knob

(Original instructions)

31. 6

2.5

31.6

FIG. 3 FIG. 4

FIG. 5 FIG. 6

ENGLISH

FIG. 7

FIG. 8

ENGLISH

31.6

22.5

2.5

1.6

31. 6

22.5

31.

(Original instructions)

FIG. 9 FIG. 10

FIG. 11

FIG. 12

(Original instructions)

ENGLISH

Key Information You Should Know:

• Cut only with sharp blades. Dull blades cut poorly and overload the motor.

• If the saw does not cut accurately, refer to the TROUBLE SHOOTING chart in this manual.

Intended use

Your Stanley Mitre Saw has been designed for fast cutting in wood, ﬁne ﬁnishing or aluminum cutting .

General Safety Instructions

WARNING: When using electric tools, basic

safety precautions should always be followed to reduce risk of ﬁre, electric shock, and personal

injury, including the following:

Read All Instructions

Safety Warnings: Double Insulation Double

insulated tools are constructed throughout with two

separate layers of electrical insulation or one double thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

Replacement parts: When servicing all tools, USE IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords.

Safety Instructions: Polarized Plugs

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is

wider than the other). This plug will ﬁt in a polarized outlet only one way. If the plug does not ﬁt fully into the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install the proper utlet. Do not change the plug in any way.

Safety Instructions For All Tools

• KEEP GUARDS IN PLACE and in working order.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches are removed from spindle before turning tool on.

• KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

• DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted.

• KEEP CHILDREN AWAY. All visitors should be kept at a

safe distance from work area.

• MAKE WORKSHOP KID PROOF with padlocks, master

switches, or by removing starter keys.

• DON’T FORCE TOOL. It will do the job better and be

safer at the rate for which it was designed.

• USE RIGHT TOOL. Don’t force tool or attachment to do

a job for which it was not designed.

• WEAR PROPER APPAREL. No loose clothing, gloves,

neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

• ALWAYS WEAR SAFETY GLASSES. Also use face or

dust mask if cutting operation is dusty. Everyday eyeglasses have only impact resistant lenses, they are NOT safety glasses.

• SECURE WORK. Use clamps or vise when you cannot

secure the workpiece on the table and against the fence by hand or when your hand will be dangerously close to the blade (within 6”).

• DON’T OVERREACH. Keep proper footing and balance

at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and

clean for best and safest performance. Follow instructions for lubricating and changing accessories.

• DISCONNECT TOOLS before servicing; when changing

accessories, such as blades, bits, cutters, and the like.

• REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in OFF position before plugging in.

• USE RECOMMENDED ACCESSORIES. Consult the

instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

• NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped or if the cutting tool is unintentionally contacted.

• CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be carefully checked to determine that it will operate

ENGLISH

(Original instructions)

properly and perform its intended function—check for

alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions

that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. Do

not use tool if switch does not turn it on and off.

• NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

• DO NOT OPERATE ELECTRIC TOOLS NEAR

FLAMMABLE LIQUIDS OR IN GASEOUS OR EXPLOSIVE ATMOSPHERES. Motors in these tools

may spark and ignite fumes.

• USE PROPER EXTENSION CORDS. Make sure your

extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Conductor size (mm2) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - 230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Additional Safety Rules For Mitre Saws

CAUTION: FAILURE TO HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND SERIOUS DAMAGE TO THE SAW.

• DO-Protect electric supply line with at least a 15 ampere time-delay fuse or a circuit breaker.

• Replace table insert when worn

• Use only saw blades recommended by the manufacturer

• Connect mitre saw to a dust connecting device when sawing

• Take care when slotting

• DO-Make certain the blade rotates in the correct direction and that the teeth at the bottom of the blade are pointing to the rear of the mitre saw.

• DO-Be sure all clamp handles are tight before starting any operation.

• DO-Be sure all blade and clamp washers are clean and recessed sides of collars are against blade. Tighten arbor screw securely.

• DO-Keep saw blade sharp.

• DO-Keep motor air slots free of chips and dirt.

• DO-Use blade guards at all times.

• DO-Keep hands out of path of saw blade.

• DO-Shut off power, disconnect cord from power source and wait for saw blade to stop before servicing or adjusting tool.

• DO-Support long work with an outboard tool rest.

• DO-Use only 10 inch diameter blades.

• Do not use saw blades which are damaged or deformed

• DON’T-Attempt to operate on anything but designated voltage.

• DON’T-Operate unless all clamp handles are tight.

• DON’T-Use blades larger or smaller than those which are recommended.

• DON’T-Wedge anything against fan to hold motor shaft.

• DON’T-Force cutting action. (Stalling or partial stalling of motor can cause major damage. Allow motor to reach full speed before cutting.)

• DON’T-Cut ferrous metals (Those with any iron or steel content) or any masonry.

• DON’T-Use abrasive wheels. The excessive heat and abrasive particles generated by them will damage saw.

• DON’T-Allow anyone to stand behind saw.

• DON’T-Apply lubricants to the blade when it’s running.

(Original instructions)

ENGLISH

• DON’T-Place either hand in the blade area when the saw is connected to the power source.

• DON’T-Use blades rated less than 5500 R.P.M.

• DON’T-Attempt to cut small pieces (hand within 6" of blade) without clamping.

• DON’T-Operate saw without guards in place.

• DON’T-Perform any operation freehand.

• DON’T-Reach around or behind saw blade.

• DON’T-Place hands closer than 6 inches from the saw blade.

• DON’T-Reach underneath the saw unless it is turned off and unplugged. The saw blade is exposed on the underside of the saw.

• DON’T-Move either hand from saw or workpiece or raise arm until blade has stopped.

• DON’T-Use without Kerf Plate or when kerf slot is wider than 3/8"

• DON’T- Carry saw by work extension or other accessory.

CAUTION: Some wood contains preservatives

such as copper chromium arsenate (CCA) which can be toxic. When cutting these materials extra care should be taken to avoid inhalation and minimize skin contact.

CAUTION: Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or other reproductive harm. Use

appropriate respiratory protection.

CAUTION: Do not connect unit to electrical power source until complete instructions are read and

understood.

For your convenience and safety, the following warning

labels are on your mitre saw.

ON MOTOR HOUSING:

WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW. WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. ALWAYS WEAR EYE PROTECTION.

ON FENCE:

CLAMP SMALL PIECES BEFORE CUTTING. SEE MANUAL.

ON GUARD:

DANGER – KEEP AWAY FROM BLADE.

ON GUARD RETAINER PLATE: “PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE USE.”

ON TABLE: (2 PLACES)

ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE. KEEP HANDS 6" FROM PATH OF SAW BLADE. NEVER PERFORM ANY OPERATION FREEHAND. NEVER CROSS ARMS IN FRONT OF BLADE. THINK! YOU CAN PREVENT ACCIDENTS. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE. NEVER REACH IN BACK OF SAW BLADE. ALWAYS WEAR EYE PROTECTION. SHUT OFF POWER AND WAIT FOR BLADE TO STOP BEFORE SERVICING, ADJUSTING TOOL, OR MOVING HANDS.

Electrical Connection

Be sure your power supply agrees with the nameplate marking. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All B&D tools are factory tested. If this tool does not operate, check the power supply.

Familiarization

Place the saw on a smooth, ﬂat surface such as a workbench or strong table. Examine Figures 1 & 2 and refer to the parts description to become familiar with the saw and its various parts. The following section on adjustments will refer to these terms and you must know what and where the parts are. The part name is followed by the corresponding part number Example - lock down pin (10). Press down lightly on the operating handle and pull out the lock down pin (10), as shown in Figure 3. Gently release the downward pressure and allow the arm to rise to its full height. Use the lock down pin when carrying the saw from one place to another. Use the operating handle (1) to transport the saw or the hand indentations (11) shown in Figure 2 after unplugging.

ENGLISH

(Original instructions)

Speciﬁcations

Capacity of cut

47° mitre left and right

47° bevel left

0° mitre -Max. Height 3-1/2” -Max. Width 5-1/2”

45° mitre -Max. Height 3-1/2” -Max. Width 4-1/8”

45° bevel -Max. Height 2-1/2” -Max. Width 5-1/2”

Bench Mounting

Bench mounting holes (8) are provided in all four feet to

facilitate bench mounting, as shown in Figure 1. (Two

different sized holes are provided to accommodate different

sizes of screws. Use either hole, it is not necessary to use

both.) Always mount your saw ﬁrmly to prevent movement.

To enhance the tool’s portability, it can be mounted to a

piece of 1/2" or thicker plywood which can then be clamped

to your work support or moved to other job sites and

reclamped.

NOTE: If you elect to mount your saw to a piece of plywood,

make sure that the mounting screws don’t protrude from the

bottom of the wood. The plywood must sit ﬂush on the work

support. When clamping the saw to any work surface, clamp

only on the clamping bosses where the mounting screw

holes are located. Clamping at any other point will interfere

with the proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be

sure the mounting surface is not warped or

otherwise uneven. If the saw rocks on the surface, place a

thin piece of material under one saw foot until the saw sits

ﬁrmly on the mounting surface.

Installing a New Saw Blade

(UNPLUG THE MITRE SAW)

DO NOT USE FERROUS METAL or masonry cutting blades

in this saw

• Loosen hex bolt on center cover counter clockwise with

box wrench.

• Lift up the safe cover and center cover.

• Press down the lock to lock spindle.

• Loosen hex bolt clockwise with box wrench, then dismount the bolt and ﬂange.

• Mount the blade of saw on spindle. Make sure that the

arrow direction on surface of saw blade is same as one of the cover.

Note: There are two different internal diameters of cutter in inner plate which have steel stamp marked 25.4mm 16mm. When mounting, the outer diameter of inner plate must be correspondent with the internal diameter of saw blade.

• Mount ﬂange and hex bolt.

• Press axle lock and tighten hex bolt counter clock wise with box wrench ﬁrmly, then tighten hex bolt clockwise to ﬁx centre cover.

Note: Only use attached wrench when mounting or dismounting saw blade. When dismounting saw blade, lift up safe cover and centre cover. Loosen hex bolt with box

wrench and disassemble hex bolt, ﬂange and saw blade.

NEVER DEPRESS THE SPINDLE LOCK PIN WHILE THE BLADE IS ROTATING.

• Be sure to hold the guard bracket down and ﬁrmly tighten the guard bracket screw when you ﬁnish installing

the saw blade. Failure to do so will cause serious damage to the saw.

Assembling and Adjusting Your Saw

PERFORM ALL ASSEMBLY WITH SAW UNPLUGGED.

Attach Mitre Clamp Handle

Remove the mitre clamp handle (4) from the plastic parts bag and carefully thread it into the bracket in the front of the saw.

Attaching Dust Bag

A zippered cloth dust bag is included with your saw. To

attach the bag, ﬁt the plastic opening ﬁrmly over the dust

spout (9).

NOTE: The saw can also be used with a vacuum cleaner hose attached to the dust spout or without any attachment.

Adjustments

PERFORM ALL ADJUSTMENTS WITH THE MITRE SAW UNPLUGGED

NOTE: Your mitre saw is fully and accurately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw.

(Original instructions)

ENGLISH

Mitre Scale Adjustment

Place a square against the saw’s fence and blade, as shown in Figure 4. (Do not touch the tips of the blade teeth with the square. To do so will cause an inaccurate measurement.) Loosen the mitre clamp handle (4) as shown in Figure 5 and swing the mitre arm until the mitre latch (5) locks it at the 0 mitre position. Do not tighten the clamp handle. If the saw blade is not exactly perpendicular to the fence, loosen the two screws that hold the handle to the base (shown in Figure 6) and move the arm of the saw left or right until the blade is perpendicular to the fence, as measured with the square. Retighten the two screws. Pay no attention to the reading of the mitre pointer at this point.

Guard Actuation and Visibility

The blade guard on your saw has been designed to automatically raise when the arm is brought down and to lower over the blade when the arm is raised. The guard can be raised by hand when installing or removing saw blades or for inspection of the saw. NEVER RAISE THE BLADE GUARD MANUALLY UNLESS THE SAW IS TURNED OFF.

NOTE: Certain special cuts will require that you manually raise the guard. To do this, simply place your right thumb on the upper side of the guard and roll the guard up just enough to clear the workpiece. Never tie up or otherwise prevent the guard from operating normally.

Operation

Plug the saw into any power source. Refer to the nameplate for voltage. Be sure the cord will not interfere with your work.

Switch

To turn the saw on, depress the trigger switch (16). To turn the tool off, release the switch. There is no provision for locking the switch on.

Body and Hand Position (See ﬁgure 7)

Proper positioning of your body and hands when operating the mitre saw will make cutting easier, more accurate and safer. Never place hands near cutting area. Place hands no closer than 6" from the blade. Hold the workpiece tightly to the table and the fence when cutting. Keep hands in position until the trigger has been released and the blade has completely stopped. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS HANDS, AS SHOWN IN FIGURE 7.

Cutting With Your Saw

NOTE: Although this saw will cut wood and many nonferrous

materials, we will limit our discussion to the cutting of wood only. The same guidelines apply to the other materials. DO NOT CUT FERROUS (IRON AND STEEL) MATERIALS OR MASONRY WITH THIS SAW. Do not use any abrasive blades.

Crosscuts

NOTE: Cutting of multiple pieces is not recommended, but

can be done safely by ensuring that each piece is held ﬁrmly

against the table and fence.

A crosscut is made by cutting wood across the grain at any angle. A straight crosscut is made with the mitre arm at the zero degree position. Set the mitre arm at zero, hold the

wood on the table and ﬁrmly against the fence. Turn on the

saw by squeezing the trigger switch. When the saw comes up to speed (about 1 second) lower the arm smoothly and slowly to cut through the wood. Let the blade come to a full stop before raising arm.

Mitre crosscuts are made with the mitre arm at some angle other than zero. This angle is often 45 degrees for making corners, but can be set anywhere from zero to 47 degrees left or right. After selecting the desired mitre angle, be sure to tighten the mitre clamp handle (4). Make the cut as described above.

Bevel Cuts

A bevel cut is a crosscut made with the saw blade at a bevel to the wood. In order to set the bevel, loosen the bevel clamp knob (17) and move the saw to the left as desired. Once the desired bevel angle has been set, tighten the bevel

clamp knob ﬁrmly. Bevel angles can be set up to 45 degrees

left and can be cut with the mitre arm set between zero and 47 degrees right or left.

Quality of Cut

The smoothness of any cut depends on a number of variables. Things like material being cut, blade type, blade sharpness and rate of cut all contribute to the quality of the cut.

When smoothest cuts are desired for molding and other precision work, a sharp (60 tooth carbide) blade and a slower, even cutting rate will produce the desired results. Ensure that material does not creep while cutting, clamp it securely in place. Always let the blade come to a full stop before raising arm.

ENGLISH

(Original instructions)

If small ﬁbers of wood still split out at the rear of the

workpiece, stick a piece of masking tape on the wood where the cut will be made. Saw through the tape and carefully

remove tape when ﬁnished.

Keep both feet ﬁrmly on the ﬂoor and maintain proper

balance. As you move the mitre arm left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard louvers when following a pencil line

Clamping the Workpiece

Turn Off and Unplug Saw

If you cannot secure the workpiece on the table and against the fence by hand (irregular shape, etc.) or your hand will be

within 6” of the blade, a clamp or ﬁxture must be used.

Other convenient clamps such as spring, bar or Cclamps may be appropriate for certain sizes and shapes of workpieces. Use care in selecting and placing these clamps and make a dry run before making the cut.

Support for Long Pieces

Turn Off and Unplug Saw

ALWAYS SUPPORT LONG PIECES For best results, use an extension work support to extend the table width of your saw. Support long workpieces using any convenient means such as sawhorses or similar devices to keep the ends from dropping.

Cutting Picture Frames, and Other Four Sided Projects

To best understand how to make the items listed here, we suggest that you try a few simple projects using scrap wood until you develop a “FEEL” for your saw. Your saw is the perfect tool for mitring corners like the ones shown in Figure 8, which shows a joint made by setting the mitre arm at 45 degrees to to mitre the two boards to form a 90 degree corner. To make this type of joint, set the mitre arm to 45

degrees. The wood was positioned with the broad ﬂat side

against the table and the narrow edge against the fence.

As the number of sides changes, so do the mitre angles. The chart below gives the proper angles for a variety of shapes.

(The chart assumes that all sides are of equal length.) For a shape that is not shown in the chart, use the following formula. 180 degrees divided by the number of sides equals the mitre.

- Examples -

No. Sides Angle Mitre

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

Cutting Compound Mitres

A compound mitre is a cut made using a mitre angle and a bevel angle at the same time. This is the type of cut used to make frames or boxes with slanting sides like the one shown in Figure 8.

NOTE: If the cutting angle varies from cut to cut, check that the bevel clamp knob (10) and the mitre clamp handle (4) are securely tightened. These knobs must be tightened after making any changes in bevel or mitre.

Cutting Crown Molding

In order to ﬁt properly, crown molding must be mitred with extreme accuracy. The two ﬂat surfaces on a given piece of

crown molding are at angles that, when added together, equal exactly 90 degrees. Most, but not all, crown molding

has a top rear angle (the section that ﬁts ﬂat against the

ceiling) of 52 degrees and a bottom rear angle (the part that

ﬁts ﬂat against the wall) of 38 degrees.

Pretesting with scrap material is extremely important! Place the bottom side (the side that will be against the wall) against the Mitre SAW FENCE. Place the top (that part that will be against the ceiling) against the saw table and the crown molding fence. Instructions for cutting crown MOLDING angled between the fence and the TABLE of the saw for all cuts:

1. Angle the molding so the bottom of the molding (part which goes against the wall when installed) is against the fence and the top of the molding is resting on the table of the saw.

(Original instructions)

ENGLISH

2. The angled “ﬂats” on the back of the molding must rest squarely on the fence and table of the saw.

INSIDE CORNER:

Left side

1. Mitre right at 45°

2. Save the right side of cut

Right side

1. Mitre left at 45°

2. Save left side of cut

OUTSIDE CORNER:

Left side

1. Mitre left at 45°

2. Save the right side of cut

Right side

1. Mitre right at 45°

2. Save left side of cut

ALWAYS MAKE DRY RUNS TO CHECK FOR CLEARANCE AND CORRECTNESS OF CUTS.

Special Cuts

NEVER MAKE ANY CUTS UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.

Aluminum Cutting (Carbide tipped blade only)

Aluminum extrusions such as those used when making aluminum screens and storm windows can easily be cut with your saw using the proper blade designed for non-ferrous metal cutting. Position the material so that you will be cutting the thinnest cross section, as shown in Figure 9.

Figure 10 illustrates the wrong way to cut these extrusions. Use a wax lubricant when cutting aluminum such as Johnson’s Stick Wax No.140. Apply the stick wax directly to the saw blade before cutting. Never apply stick wax to a moving blade.

The wax, available at most hardware stores and industrial mill supply houses, provides proper lubrication and keeps chips from adhering to the blade.

Be sure to properly secure work. Certain workpieces, due to their size, shape or surface ﬁnish, may require the use of a clamp, jig or ﬁxture to prevent movement during the cut.

Bowed Material

When cutting bowed material always position it as shown in Figure 11 and never like that shown in Figure 12. Positioning the material incorrectly will cause it to pinch the blade near the completion of the cut.

Cutting Plastic Pipe and other round cross-sectional material

Plastic pipe can be easily cut with your saw. It should be cut just like wood and clamped or held ﬁrmly to the fence to keep it from rolling particularly when making angle cuts.

Carrying the tool

1. Lower the cutting head and push in the lock pin (10)

2. Carry the mitre saw with the carrying handles (11).

Warning! Do not carry the machine by the guard.

DURING USE

• If the saw blade becomes blocked, switch off the tool immediately and disconnect the plug; only then remove the wedged workpiece

• In case of jamming or electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug

Maintenance

(PERFORM ALL MAINTENANCE WITH MITRE SAW UNPLUGGED.)

1. All bearings are sealed. They are lubricated for life and need no further maintenance.

2. Periodically clean all dust and wood chips from around AND UNDER the base and the rotary table. Even though slots are provided to allow debris to pass through, some dust will accumulate.

3. The brushes are designed to give you several years of use. If they ever need replacement follow the instructions in this manual or return the tool to the nearest service center for repair.

Important

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualiﬁed service organizations, always using identical replacement parts.

ENGLISH

(Original instructions)

Trouble Shooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE! SAW WILL NOT START

WHAT’S WRONG? WHAT TO DO…

1. Saw not plugged in 1. Plug in saw

2. Fuse blown or circuit 2. Replace fuse or reset breaker tripped circuit breaker

3. Cord damaged 3. Have cord replaced by authorized service center

4. Brushes worn out 4. See “Brushes” in this manual

TROUBLE! SAW MAKES UNSATISFACTORY CUTS

WHAT’S WRONG? WHAT TO DO…

1. Dull blade 1. Replace blade

2. Blade mounted 2. Turn blade around backwards

3. Gum or pitch on blade 3. Remove blade and clean with turpentine and coarse steel wool or household oven cleaner

4. Incorrect blade for work 4. Change the blade being done

TROUBLE! MACHINE VIBRATES EXCESSIVELY

WHAT’S WRONG? WHAT TO DO…

1. Saw not mounted 1. Tighten all mounting securely hardware

2. Stand or bench on 2. Reposition on ﬂat level uneven ﬂoor surface

3. Damaged saw blade 3. Replace blade

TROUBLE! DOES NOT MAKE ACCURATE MITRE CUTS

WHAT’S WRONG? WHAT TO DO…

1. Mitre scale not adjusted 1. Check and adjust correctly

2. Blade is not square to 2. Check and adjust fence

3. Workpiece moving 3. Clamp workpiece to fence or glue 120 grit sandpaper to fence with rubber cement

TROUBLE! MATERIAL PINCHES BLADE

WHAT’S WRONG? WHAT TO DO…

1. Cutting bowed material 1. Position bowed material as shown in Figure 11

Speciﬁcations

STSM1510

TROUBLE! BLADE DOES NOT COME UP TO SPEED

WHAT’S WRONG? WHAT TO DO…

1. Extension cord too light 1. Replace with adequate or too long size cord

2. Low house current 2. Contact your electric company

POWER W 1500

NO-LOAD SPEED /min 5500

MAX. DIAMETER mm 140x70

BLADE DIAMETER mm 254

BLADE BORE mm 30

Weight kg 12.5

(Original instructions)

ENGLISH

Service Information

Stanley offers a full network of company-owned and authorized service locations throughout Asia. All Stanley Service Centers are staffed with trained personnel to

provide customers with efﬁcient and reliable power tool

service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Stanley location nearest to you.

NOTE

• Stanley's policy is one of continuous improvement to our

products and, as such, we reserve the right to change

product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

• Complete product range may not be available in all

countries. Contact your local Stanley dealers for range availability.

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you ﬁnd one day that your Stanley product needs

replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Stanley provides a facility for the collection and recycling of Stanley products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Stanley ofﬁce at the address

indicated in this manual. Alternatively, a list of authorised Stanley repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com

ENGLISH

(Original instructions)

Two years full warranty

If your Stanley product becomes defective due to faulty materials or workmanship within 24 months from the date of purchase, Stanley Europe guarantees to replace all defective parts free of charge or – at our discretion – replace the unit free of charge provided that:

• The product has not been misused and has been used in

accordance with the instruction manual.

• The product has been subject to fair wear and tear;

• Repairs have not been attempted by unauthorised persons;

• Proof of purchase is produced.

• The Stanley product is returned complete with all original

components

If you wish to make a claim, contact your seller or check the location of your nearest authorised Stanley repair agent in

the Stanley catalogue or contact your local Stanley ofﬁce at

the address indicated in this manual. A list of authorised Stanley repair agents and full details of our after sales service is available on the internet at:www.stanleytools.com

+ 30 hidden pages

Stanley STSM1510-B9 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual