Stanley STGS7115, STGS9125, STGT6100, STGS5115, STGS7100 Original Instructions Manual

STGS7115

English Page 4

ENGLISH

2

(Original instructions)

Figure 1

b

c

c

d

h

f

g

e

i

k

Figure 2 Figure 3

n

a

3

ENGLISH

(Original instructions)

Figure 5

Figure 6

Figure 4

h

f

d

e

15o-30

o

A B

ENGLISH

4

(Original instructions)

Definitions: Safety Guidelines

The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.

Danger: Indicates an imminently hazardous
situation which, if not avoided, will result in

death or serious injury.

Warning: Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.

Caution: Indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.

Notice: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

Denotes risk of electric shock.

Denotes risk of fire.

Warning: To reduce the risk of injury, read the
instruction manual.

General Power Tool Safety Warnings

Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and

instructions may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for future reference

The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated
(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of
electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of
electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric
shock.

f) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of

electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in
serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.

5

ENGLISH

(Original instructions)

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.Carrying power tools with your finger on the

switch or energising power tools that have the switch on
invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal
injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

toolin unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are
connected and properly used. Use of these devices

can reduce dust related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was
designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools.Such preventive safety measures reduce

the risk of starting the power tool accidentally

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained
users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions, takinginto
account the working conditions and the work to be
performed. Use of the power tool for operations different

from those intended could result in a hazardous
situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is
maintained.

Additional specific safety rules

Safety Instructions for All Operations

Safety Warnings Common for Grinding

a) This power tool is intended to function as a grinder.

Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.

Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.

b) Operations such as cutting-off , sander, wire brush

or polisher are not recommended to be performed
with this power tool. Operations for which the power

tool was not designed may create a hazard and cause
personal injury.

c) Do not use accessories which are not specifically

designed and recommended by the tool
manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe
operation.

d) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed

can break and fly apart.