Stanley ProSet PB3400 Accessories Manual

Accessories Manual

NA

Original Instruction

E N G LI S H

©2016 STANLEY Black & Decker
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically or
mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided is
based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening pursues a policy of
continuous product improvement and therefore the products may be subject to change. The information provided is applicable
to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered Fastening cannot be held liable
for any damage resulting from deviations from the original specifications of the product.

The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept
any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening will
not accept any liability for damage resulting from activities carried out by third parties. The working names, trade names,
registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the
legislation with respect to the protection of trade marks.

This instruction manual must be read by any person installing or operating this tool with particular

attention to the following safety rules.

1. Safety Definitions

The definitions below describe the level of severity for each signal word. Please read the manual and pay
attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property
damage.

Denotes risk of electric shock

Denotes risk of fire

Improper operation or maintenance of this product could result in serious injury and property damage.
Read and understand all warnings and operating instructions before using this equipment. When using
power tools, basic safety precautions must always be followed to reduce the risk of personal injury.

1.1. GENERAL SAFETY

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.

• Do not use outside the design intent of Placing STANLEY Engineered Fastening Blind Fasteners.

• Use only parts, fasteners, and accessories recommended by the manufacturer.

• Use Power Tool only with specifically designated battery packs.

1.2. POWER TOOL USE AND CARE

• The tool must be maintained in a safe working condition at all times and examined at regular intervals for damage and
function by trained personnel. Any dismantling procedure will be undertaken only by trained personnel. Do not
dismantle this tool without prior reference to the maintenance instructions.

• Do not modify the tool in any way. Any modification to the tool is undertaken by the customer and will be the
customer’s entire responsibility and void any applicable warranties.

• Disconnect the battery from the tool before performing any maintenance, attempting to adjust, fit or remove a nose
assembly.

• Prior to use, check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects
the tool’s operation. If damaged, have the tool serviced before using. Remove any adjusting key or wrench before use.

• Prior to use, inspect battery for damage. Do not drop battery. A sharp impact may cause internal damage and lead to
premature battery failure.

• Keep work area clean and well lit.

• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts.

Loose clothes, jewelry or long hair can be caught in moving parts.

• Adopt a firm footing or a stable position before operating the tool.

• Operators and others in work area must wear ANSI Z87.1 CAN/CSA Z94.3 approved safety glasses with side shields.

Always wear safety glasses and ear protection during operation.

• Adequate clearance is required for the tool operator’s hands before proceeding.

• Do not operate a tool that is directed towards any person(s).

• DO NOT operate tool with the nose housing removed.

• Do not operate the tool or the charger in an explosive atmosphere or environment allowing exposure to combustible

fluids or gasses.

• Do not operate the tool or the charger in an environment allowing exposure to moisture or rain to avoid risk of electric
shock.

• Do not abuse the tool by dropping or using it as a hammer.

• Keep dirt and foreign matter out of the air vents of the tool as this will cause the tool to malfunction.

• Keep tool handles dry, clean, and free from oil and grease.

• When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent activation.

• Never leave operating tool unattended.

• Disconnect battery when tool is not in use.

1.3. IMPORTANT SAFETY INSTRUCTIONS FOR ALL BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery

chargers (refer to Technical Data).

• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.

WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.

CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT®/POP®Avdel® rechargeable batteries. Other

types of batteries may burst causing personal injury and damage.

CAUTION: Children should be supervised to ensure that they do not play with the appliance.

NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the

charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool,
aluminium foil or any build-up of metallic particles should be kept away from charger cavities. Always unplug the charger
from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and
battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging DEWALT®/POP®Avdel® rechargeable batteries. Any
other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire,
electric shock, or electrocution.

• Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots
and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is
ventilated through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug—have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an

authorised service centre.

• Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce this risk.

• NEVER attempt to connect two chargers together.

• The charger is designed to operate on standard household electrical power (refer to charger specifications). Do not

attempt to use it on any other voltage. This does not apply to the vehicular charger.

1.4. IMPORTANT SAFETY INSTRUCTIONS FOR ALL BATTERY PACKS

When ordering replacement battery packs, be sure to include catalog number and voltage.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Inserting or removing the battery from the charger may ignite the dust or fumes.

• Never force battery pack into charger. Do not modify battery pack in any way to fit into a non-compatible charger as
battery pack may rupture causing serious personal injury.

• Charge the battery packs only in DEWALT®/POP®Avdel® chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40 ˚C (104 ˚F)

(such as outside sheds or metal buildings in summer).

• When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other
small metal objects that can make a connection from one terminal to another.