Stanley ProSert XTN20 Accessories Manual
ProSertTM XTN20 Blind Rivet Nut Tool – 74202
Hydro-Pneumatic Power Tool
Accessories Manual
Original Instruction
Hydro-Pneumatic
Blind Rivet Nut Tool
STANLEY Engineered Fastening policy is one of continuous product development and
improvement and we reserve the right to change the specication of any product without prior notice.
Nose Assemblies
Nose equipment varies according to the blind rivet nut type being installed. Each nose assembly represents
a unique set of components which can be ordered individually (see below). All nose assemblies also include
a nose tip locknut 3 (part number 07555-00901). Component numbers refer to the illustration below. We
recommend maintaining some stock of spares as items will need regular replacement if worn. Read the
Servicing Manual for nose assembly instructions.
Nose Assembly Breakdown
Fitting Instructions
Item numbers in bold refer to nose assembly components in the exploded illustration.
t IMPORTANT Air supply must be disconnected from the tool before working on the nose assembly.
t If still tted, remove the Nose Casing 4 and the Chuck Nut 5.
t Insert Drive Shaft 7 into Mandrel Adaptor 8.
t Fit Mandrel 1 onto Drive Shaft 7.
t Insert Reducing Sleeve 6 (if specied) into the Chuck Nut 5.
t Screw the Chuck Nut 5 onto the Mandrel Adaptor 8 whilst pulling back the spring loaded Nose Rod 9.
Tighten the Chuck Nut 5 clockwise.
t Screw on the Nose Casing 4 and Nose Tip 2 with the nose tip Lock Nut 3.
t The reverse operation is carried out for equipment removal.
With the tool still disconnected from the air supply
t Screw an blind rivet nut onto the Mandrel manually.
t Position Nose Tip 2 on the Nose Casing 4 and lock it with Lock Nut 3 so that the blind rivet nut lines up
with the end of Mandrel 1.
t Lock the nose tip Lock Nut 3 by turning clockwise with a spanner. Remove the blind rivet nut from
Mandrel 1.
9
3
4
5
6
1
7
8
2
Fig. 1
ENGLISH
2
*Places all blind rivet nuts listed in this section except M5 large ange Thin sheet Nutsert®
**Places M5 large ange Thin Sheet Nutsert® 09698-00516 ONLY
Please see the instruction Manual (7900-09300) for full details of the tool placing capability for the
dierent Blind Rivet Nut types and sizes.
Thread Type Thread Size Assembly 1 2 6 7
M3 07555-09883 07555-09003 07555-00903 07555-09103 07555-01003
M4 07555-09884 07555-09004 07555-00904 07555-09104 07555-01004
M5* 07555-09885 07555-09005 07555-00905 07555-09105 07555-01005
M5** 07555-09185 07555-09005 07555-00915 07555-09105 07555-01005
M6 07555-09886 07555-09006 07555-00906 07555-09106 07555-01006
M8 07555-09888 07555-09008 07555-00908 07555-09108 07555-01008
M10 07555-09880 07555-09010 07555-00910 - 07555-01010
4 UNC 07555-09854 07555-09054 07555-00854 07555-09154 07555-00754
6 UNC 07555-09856 07555-09056 07555-00856 07555-09156 07555-00756
8 UNC 07555-09858 07555-09058 07555-00858 07555-09158 07555-00758
10 UNC 07555-09850 07555-09050 07555-00850 07555-09150 07555-00750
1/4 UNC 07555-09848 07555-09048 07555-00848 07555-09148 07555-00748
5/16 UNC 07555-09840 07555-09040 07555-00840 07555-09140 07555-00740
3/8 UNC 07555-09842 07555-09042 07555-00842 - 07555-00742
10 UNF 07555-09870 07555-09070 07555-00850 07555-09150 07555-00750
1/4 UNF 07555-09868 07555-09068 07555-00848 07555-09148 07555-00748
5/16 UNF 07555-09860 07555-09060 07555-00840 07555-09140 07555-00740
3/8 UNF 07555-09862 07555-09062 07555-00842 - 07555-00742
3/16 BSW 07555-09816 07555-09016 07555-00850 07555-09150 07555-00750
1/4 BSW 07555-09818 07555-09018 07555-00848 07555-09148 07555-00748
5/16 BSW 07555-09810 07555-09019 07555-00840 07555-09140 07555-00740
M3 07555-09983 07555-09003 07555-00993 07555-09103 07555-01003
M4 07555-09984 07555-09004 07555-00994 07555-09104 07555-01004
M5 07555-09985 07555-09005 07555-00995 07555-09105 07555-01005
M6 07555-09986 07555-09006 07555-00996 07555-09106 07555-01006
M8 07555-09988 07555-09008 07555-00998 07555-09108 07555-01008
M10 07555-09980 07555-09010 07555-00999 - 07555-01010
4 UNC 07555-09954 07555-09054 07555-00954 07555-09154 07555-00754
6 UNC 07555-09956 07555-09056 07555-00956 07555-09156 07555-00756
8 UNC 07555-09958 07555-09058 07555-00958 07555-09158 07555-00758
10 UNC 07555-09950 07555-09050 07555-00950 07555-09150 07555-00750
1/4 UNC 07555-09948 07555-09048 07555-00948 07555-09148 07555-00748
5/16 UNC 07555-09940 07555-09040 07555-00940 07555-09140 07555-00740
10 UNF 07555-09970 07555-09070 07555-00950 07555-09150 07555-00750
1/4 UNF 07555-09968 07555-09068 07555-00948 07555-09148 07555-00748
5/16 UNF 07555-09960 07555-09060 07555-00940 07555-09140 07555-00740
3/16 BSW 07555-09916 07555-09016 07555-00950 07555-09150 07555-00750
1/4 BSW 07555-09918 07555-09018 07555-00948 07555-09148 07555-00748
0BA 07555-09930 07555-09030 07555-00996 07555-09106 07555-01006
2BA 07555-09932 07555-09032 07555-00950 07555-09150 07555-00750
4BA 07555-09934 07555-09034 07555-00934 07555-09134 07555-00756
M3 07555-09283
07555-09003
07555-08103 07555-09103 07555-01003
M4 07555-09284 07555-09004 07555-08104 07555-09104 07555-01004
M5 07555-09285 07555-09005 07555-08105 07555-09105 07555-01005
M6 07555-09286 07555-09006 07555-08106 07555-09106 07555-01006
M8 07555-09288 07555-09008 07555-00998 07555-09108 07555-01008
UNF
SQUARESERT® (GK08) + EUROSERT® (39002, 39006) + HEXSERT® (39101, 39102, 49141) + COUNTERSUNK NUTSERT® (FW96,
GM17, GM57) + DK/DL SERIES + ALL LARGE FLANGE INSERTS (9698, FS58, FW78, GM68, 9408, 9418, 9498, 39301)
POP® NUT (STANDARD, KNURLED, CLOSED END, HEXAGONAL, TETRA NUT)
Standard
Metric
UNC
BA
HEXSERT® (9688)
Standard
Metric
BSW
THIN SHEET NUTSERT® (9468, FS38, 9658)
Standard
Metric
UNC
UNF
BSW
ENGLISH
3
Loading...