Stanley J5CP Instruction Manual
120
500 AMP BATTERY JUMP-STARTER
WITH COMPRESSOR AND POWER INVERTER
INSTRUCTION MANUAL
PUENTE AUXILIAR DE ARRANQUE
DE 500 A
CON
COMPRESOR Y INVERSOR DE PODER
MANUAL DE INSTRUCCIÓN
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.
© 2013 Baccus Global LLC
Boca Raton, FL 33432
Customer Service: (877) 571-2391
J5CP
English page 3
Español pagina 13
BC
J5CP_ManualENSP_051413.indd 20-1 1/16/2014 9:46:23 AM
2 3
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in
property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the
risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and
property damage. There are certain applications for which tools and equipment are designed. Manufacturer strongly recommends
that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all
warnings and operating instructions before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating jump-starter. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth
defect or other reproductive harm. Wash hands after handling.
This unit was designed for household use only.
WARNING: WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS OR
PROPERTY:
• Avoid dangerous environments. Don’t use appliances in damp or wet locations. Don’t use appliances in the rain.
• Keep children away. All visitors should be kept at a distance from work area.
• Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-
skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.
• Use safety glasses and other safety equipment. Use safety goggles or safety glasses with side shields, complying with
applicable safety standards. Safety glasses or the like are available at extra cost at your local dealer.
• Store idle appliance indoors. When not in use, appliances should be stored indoors in dry, and high or locked-up place – out
of reach of children.
• Don’t abuse cord. Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp
edges.
• Disconnect appliances. Disconnect the appliance from the power supply when not in use, before servicing, and when changing
accessories.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are
available having built in GFCI protection and may be used for this measure of safety.
• Use of accessories and attachments. The use of any accessory or attachment not recommended for use with this appliance
could be hazardous. Refer to the accessory section of this manual for further details.
• Stay alert. Use common sense. Do not operate appliance when you are tired or impaired.
FEATURES
CARACTERÍSTICAS
FEATURES
1. Three-prong 120 volt AC outlet
2. USB power button
3. USB power indicator
4. USB charging port (under protective cover)
5. 12 volt DC accessory outlet (under protective cover)
6. Battery status LED indicators
7. Reverse polarity indicator
8. Battery power level button
9. Area light power button
10. Pivoting LED emergency light
11. Jump-starter power switch
12. Inverter power indicator
13. Inverter power switch
14. Built-in 120 volt AC charger
15. Air pressure gauge
16. Positive (+) red clamp
17. Air hose and Surefit™ nozzle
18. Compressor power switch
19. Negative (–) black clamp
20. 12 Volt DC charging adapter (optional accessory)
21. Nozzles
CARACTERÍSTICAS
1. Tomacorriente de tres patas de CA de 120 voltios
2. Botón de la energía del USB
3. Indicador de energía del USB
4. Puerto de carga del USB (bajo cubierta protectora)
5. Tomacorriente para accesorios de 12 V de CC
(bajo cubierta protectora)
6. Indicadores de estado de la batería del LED
7. Indicador de polaridad inversa
8. Botón del nivel de energía de batería
9. Botón de encendido de la luz zonal
10. Lúz LED giratoria para emergencias
11. Interruptor de encendido del puente auxiliar de arranque
12. Indicador de energía del convertidor
13. Interruptor del convertidor
14. Cargador de CA de 120 voltios incorporado
15. Galga de presión
16. Pinza roja del positivo (+)
17. Manguera de aire e SureFit™ inyector de aire
18. Interruptor del compresor
19. Pinza negra del negativo (–)
20. Adaptador de carga de la CC de 12 voltios
(accesorio opcional)
21. Picos
20 21
4
5
6
7 8
10
16 1917 18
14 15
2
12
9
1
3
11
13
J5CP_ManualENSP_051413.indd 2-3 1/16/2014 9:46:23 AM
4 5
SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS
WARNING: BURST HAZARD:
• Never leave the compressor unattended while in use.
• Carefully follow instructions on articles to be inflated.
• Never exceed the recommended pressure listed in instructions on articles to be inflated. If no pressure is given, contact article
manufacturer before inflating. Bursting articles can cause serious injury.
• Always check pressure with the pressure gauge.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Do not operate compressor continuously for longer than approximately 10 minutes, depending on ambient temperatures, as it may
overheat. In such event, compressor may automatically shut down. Turn off the compressor power switch immediately and restart
after a cooling down period of approximately 30 minutes.
SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS
WARNING: BURST HAZARD
Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and
cause injury to persons and damage property. Use the unit for charging/boosting a lead-acid battery only. It is not intended to
supply power to a low-voltage electrical system other than in a starter-motor application.
• Use of an attachment not supplied, recommended or sold by manufacturer specifically for use with this unit may result in a risk of
electrical shock and injury to persons.
WARNING: RISK OF EXPLOSIVE GASES
• Working in the vicinity of a lead acid battery is dangerous. Batteries generate explosive gases during normal battery operation.
For this reason, it is of the utmost importance that each time before using the jump-starter you read this manual and follow
instructions exactly.
• To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and
manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary markings on these products
and on the engine.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting, read
the vehicle’s owner’s manual to confirm that external-starting assistance is suitable.
• When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.
• Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be
aware of first aid procedures in case of accidental contact with battery acid.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin.
• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station
• Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid battery. A lead acid
battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin, causing a severe burn.
• Do not wear vinyl clothing when jump-starting a vehicle when jump-starting a vehicle, friction can cause dangerous staticelectrical sparks.
• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangerous sparks, power arcing
and/or explosion.
• When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all
clamps, cords, clothing and body parts away from moving vehicle parts.
• Never allow red and black clamps to touch each other or another common metal conductor — this could cause damage to the
unit and/or create a sparking/explosion hazard.
a) For negative-grounded systems, connect the POSITIVE (RED) clamp to the POSITIVE ungrounded battery post and the NEGATIVE
(BLACK) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel
lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
b) For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE ungrounded battery post and the
POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor,
fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
• If the connections to the battery’s POSITIVE and NEGATIVE terminals are incorrect, the Reverse Polarity Indicator will light (red)
and the unit will sound a beep. Disconnect clamps and reconnect to battery with correct polarity.
• Always disconnect the negative (Black) jumper cable first, followed by the positive (Red) jumper cable, except for positive
grounded systems.
• Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Check for damaged parts. Any part that is damaged should be replaced by the manufacturer before further use. Contact the
manufacturer at (877) 571-2391 for more information.
• Do not operate this appliance near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools
normally spark, and the sparks might ignite fumes.
• Never submerge this unit in water; do not expose it to rain, snow or use when wet.
• To reduce risk of electric shock, disconnect the unit from any power source before attempting maintenance or cleaning.
Turning off controls without disconnecting will not reduce this risk.
• This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a garage or
enclosed area, the unit MUST be placed not less than 18 inches above the floor.
• Do not use this unit to operate appliances that need more than 5 amps to operate from the 12 volt DC accessory
outlet.
• Do not insert foreign objects into either the USB outlet or the 12 volt DC accessory outlet.
SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT
• IMPORTANT: This unit is delivered in a partially charged state. Fully charge unit with a household extension cord (not supplied)
for a full 40 hours before using for the first time. You cannot overcharge the unit using the AC charging method.
• To recharge this unit, use only the supplied AC charging adapter.
• All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF
position before connection to a power source or load.
WARNING: SHOCK HAZARD
• Do not operate charger with damaged cord or plug – replace the cord or plug immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way.
• Do not disassemble charger. Incorrect reassembly may result in a risk of electric shock or fire.
• Outdoor use extension cords. When appliance is used outdoors, use only extension cords intended for use outdoors and so
marked.
• Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power
and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
MINIMUM GAGE FOR CORD SETS
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)
240V 0-50 51-100 101-200 201-300
(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)
Ampere Rating Extension Cord Length
More Not more
0’-25’ 26’-50’ 51 ’-100 ’ 101’ -150 ’
Than Than American Wire Gage (AWG)
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
• When an extension cord is used, make sure that:
a) the pins of extension cord are the same number, size and shape as those in the charger,
b) the extension cord is properly wired and in good electrical condition,
c) the wire size is large enough for the AC rating of the charger.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Pull by the plug rather than the cord when
disconnecting the 12V DC charging adapter from the unit.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE WHEN CHARGING USING THE 12 VOLT DC METHOD:
• Recharge using this method only when necessary. Frequent use the the 12 volt DC charging method may shorten battery life.
• DO NOT EXCEED 6 HOURS CHARGING TIME USING THIS METHOD.
J5CP_ManualENSP_051413.indd 4-5 1/16/2014 9:46:23 AM
6 7
Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
If the the battery is overly discharged and the green LED lights when the charger is plugged in, this indicates the battery is at a high impedance stage. If
this occurs, recharge the unit and leave it charging for a period of 24-48 hours before use.
Charging/Recharging Using the 120 Volt AC Charger and a Standard Household Extension Cord (not included)
1. Lift the AC adapter cover located on the back of the unit and connect an extension cord to the unit. Plug the other end of the
cord into a standard 120volt AC wall outlet.
2. Charge until two red and one green LED battery status indicators light or flash.
3. Once fully charged, disconnect the extension cord.
Notes:
The unit cannot be overcharged using this method.
The unit will not charge if the inverter power switch is turned on.
12 Volt DC Charging Method
Charging the unit from an external 12 volt DC power source requires the use of the 12 volt DC adapter (optional accessory). This
adapter has a male DC connector at each end.
1. Inser t the gold-tipped 12 volt DC charging adapter plug into the vehicle’s 12 volt DC accessory outlet.
2. Inser t the silver-tipped end plug into the 12 volt DC accessory outlet on the front panel of the unit.
3. Charge the unit until the green FULL indicator lights when the Battery Power Level Button is pressed (with the adapter
unplugged from the unit). DO NOT CHARGE MORE THAN 6 HOURS MAXIMUM USING THIS METHOD.
4. When charging is complete, remove the charging cord and store in a safe place.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power the accessory outlet.
DO NOT LEAVE THE UNIT UNATTENDED WHEN CHARGING USING THIS METHOD.
JUMP-STARTER
This Jump-Starter is equipped with an On/Off power switch. Once the connections are properly made, turn the switch on to jumpstart the vehicle.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place vehicle in “park” and
set the emergency brake.
2. Make sure the Jump-Starter power switch is turned to off.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis)
(MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery’s positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to
negative battery terminal or moving part. Refer to the automobile owner’s manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Note:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a
and 4b above with steps 5a and 5b, then proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery’s negative terminal.
5b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly
to Positive battery terminal or moving part. Refer to the automobile owner’s manual.
6. When clamps are connected properly, turn the Jump-Starter power switch to ON.
7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
8. Turn the Jump-Starter power switch back to the OFF position.
9. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE “SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS”
SECTION OF THIS INSTRUCTION MANUAL.
• This power system is to be used ONLY on vehicles with 12volt DC battery systems.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or explosion.
• After use, turn the Jump-Starter power switch off.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting this
type of vehicle, read the vehicle manual to confirm that external-starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails to start after the recommended number of
attempts, discontinue jump-start procedure and look for other problems that need to be corrected.
• If the connections to the battery’s positive and negative terminals are incorrect, the Reverse Polarity Indicator will light and the
unit will sound a beep. Disconnect clamps and reconnect to battery with correct polarity.
• Place this unit as far away from the battery as cables permit.
• Never allow battery acid to come in contact with this unit.
• Do not operate this unit in a closed area or restrict ventilation in any way.
• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt battery system.
• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not
have a battery installed.
• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of
attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.
• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and
recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or
moisture.
FIRST AID
SKIN: If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes. If redness, pain, or
irritation occurs, seek immediate medical attention.
E YES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate
medical attention.
SPECIFIC SAFETY INSTRUCTIONS FOR INVERTERS
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Do not connect to AC distribution wiring.
• Do not make any electrical connections or disconnections in areas designated as IGNITION PROTECTED. This inverter is NOT
approved for ignition protected areas.
• Never immerse the inverter in water or any other liquid, or use when wet.
• Do not insert foreign objects into the inverter’s outlets.
WARNING: TO REDUCE THE RISK OF FIRE:
• Do not operate near flammable materials, fumes or gases.
• Do not expose to extreme heat or flames.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Disconnect appliance plug from inverter outlet before attempting any repairs to the appliance.
• Do not attempt to connect the inverter while operating your vehicle. Not paying attention to the road may result in a serious
accident.
• Always use the inverter where there is adequate ventilation. Do not block ventilation slots.
• Always turn the inverter off when not in use.
• Keep in mind that this inverter will not operate high wattage appliances or equipment that produce heat, such as hair dryers,
microwave ovens and toasters.
• DO NOT OPEN THE UNIT — there are no user-serviceable parts inside. Opening the inverter will void manufacturer’s warranty.
• Do not use this inverter with medical devices. It is not tested for medical applications.
• Operate inverter only as described in this Instruction Manual.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new 500 Amp Jump Starter with Compressor and Power Inverter. Read this Instruction Manual
and follow the instructions carefully before using this unit.
CHARGING/RECHARGING
Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from
self-discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy
lost through self-discharge. When the unit is not in frequent use, manufacturer recommends the battery be recharged at least
every 30 days.
WARNING: Never attempt to use the AC and DC charging methods at the same time.
CAUTION: RISK OF PROPERTY DAMAGE: Failure to keep the battery charged will cause permanent damage and result in poor
jump starting performance.
Notes:
This unit is delivered in a partially charged state – you must fully charge it upon purchase and before using it for the first time. Initial AC charge should be
for 40 hours.
Recharging battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life. The
battery can be recharged using either the Built-In 120 volt AC Charger or the DC charging adapter.
J5CP_ManualENSP_051413.indd 6-7 1/16/2014 9:46:23 AM
Loading...