Stanley 150 Quick Start Manual
...•
.[A31NV1Sl
051 ·oN XOH tI1llIW
-.~NOll~
NtidO
AtllNV~S
..•.
·v·s·n
'·NNO~
_'1.10M.AIlIDIIlS 1l'l.L JO DOI"IA-la
'NIV.LIlIO: .M3N
S'lOO~ X.H~NV~S
'178'0N
SIOO.L JO lSH elBldmoo .I0.il
SUA31 OOOM ONV NOHI S3SIA
.
\
,
;
S13SIH3 S.H31N3d9V3 n1nlf "OVZ Olt ••
SIIHltn6s1331S S.H31N3dHlt3 S3Nltld ,,)l30H 03B .•
83Hvn6s 3HlI ••• ONV AH! . S3Nltld "UllltB ••
Q'lllOA\
erUiOI'B'l'110 .IO,J
SNOHI 9NIH3010S 31913313
. S3AVHS 3)10dS
S93A1HO M3H3S snol 3H!1'"
S1061 9NI13MOO S111HO INVH
S93 ••••••VH S11190 18V3H8
S30nvo 833VH8 118
S31n9 1331S OIOIH 3l81X31:1
S13A3B S310H 000MX08
nu.
.tIO XOO:
[A31
NV1S]
PUBS
srss
MVS
'1001. i1HJ.
UJO.JJ
S~·lOOJ.
A31
NV,J.S
STANLEY OPEN FRONT MITRE BOX No. 150
The No. 150 Mitre Box is of sturdy construction and easily operated. The entire box, with the
.exception of the saw guides and a few minor parts,
Some of the
1. Open front construction enables cutting
.wood of extra width, and easy h'andling
of long boards.
2. 'Takes either back or hand saw. Takes·
stock up to 4 in. when hand saw is used.
Capacity when back saw is used varies
according to-width of saw blade.
3. Saw can be easily adjusted square with
back and vertical base.
4.
Machined.surfaces of the saw yoke and
swivel arm provide a perfect fit, insuring
rigidity and accuracy.
5. Turn of thumb screw adjusts guides to
exact thickness of saw.
6. Swivel can be set and locked for all
angles between 45° and 90°.
7. Length Gauge may be used on back or
front of box without removing wing nut
and screw. .
Features
Mitr:eBox
of the No. 150
is
treated with a special japan rust-resisting finish.
Directions
for Adjusting
:Mitre Box
Given Inside
This Folder
DIRECTIONS FOR ADJUSTING THE No. 150 MITRE BOX
'!
__w Guide is adjustable -for stock up to 4 inches in height.
Saw can be adjusted vertically to base by means of screws.
When doing this loosen thumb"screw.
(see arrow above)temporarily.
Swivelcan belocked at any angle by means of set screw.
Swivel engages in notches which are marked for
30° and 45° angle cuts.
I
Saw can be adjusted square to back by looseningscrew
and movingswivelto right or left.
22lh °,
~w Guidesare adjustable to thickness of saw. Thumb
screw to lock plates at prop~r size for saw.
IMPORTANT -
will prevent damage to your saw.
Keep the saw guides just above the work, leaving about one-half an inch between the saw guldes and the wood being
worked. This willprevent the saw running out oftrue.
When using No. 150 Mitre Box, do not let the
For short lengths use Length stop on front of box, for
long lengths fasten it on the back. For extra
TEETH
long work attach wooden stick of de-
of the saw comein contact with the saw guides. This
sired length to the stop.
Loading...