Standart Horizon RAM3, CMP30 Owner's Manual

RAM3 (CMP30

)

Remote Station Microphone

The RAM3 (CMP30) allows you to remotely control all functions of Standard Hori-

zon xed mount VHF radios which include GX1600, GX1700, GX2000, GX2100,
GX2150, GX2200, GX5000S and GX5500S. The full dot matrix display and pro­grammable keys make operation simple and fast. Additional features include turning
the radio on/off and all DSC functions including Distress. The RAM3 (CMP30) can
be extended up to 70 feet using the optional CT-100 (23 Foot) extension cable. The

RAM3 (CMP30) is backed by an industry leading 3-year waterproof warranty.

WARNING: Do not connect or remove the CMP30 (RAM3) microphone while

the radio is powered on. This may result in equipment failure.

1. Connect the Extension Cable to the 8-pin connector on the transceivers rear
panel, then tighten the Cable Nut (Figure 1).

2. Referring to Figure 2, attach the supplied ferrite core as close as possible to the
MIC plug of the Routing Cable and External Speaker Connections, then snap its
two halves together. And then, wind some plastic tape around the ferrite core, to
prevent vibration from causing the two halves to split apart and fall off the wires.

3. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall then insert the Exten­sion Cable into this hole. Connect the Gasket and Mount Base to the Extension
Cable Connector using the Nut.

4. Drill the four Screw holes (approx. 2 mm) on the wall then install the Mounting
Bracket to the wall using four screws.

5. Put the Rubber Cap on to the Nut.

6. The installation is now complete. Connect the RAM3 (CMP30) to the Extension
Cable Connector and tighten the Cable Nut.

RAM3 (CMP30) InstallatIon

FIgure 1

FIgure 3

Copyright 2015
YAESU MUSEN CO., LTD.
All rights reserved.

No portion of this manual
may be reproduced
without the permission of
YAESU MUSEN CO., LTD.

Included accessorIes and replacement part numbers

1. 23-Foot Routing Cable (S8101512)

2. Rubber Cap (RA052520A)

3. Mounting Bracket (RA052510) & Screws (U24312020 x 4 pcs)

4. Microphone Hanger (RA0458800: Black or RA0436000: White) &

Screws (U40412220 x 2 pcs)

5. Ferrite Core (L9190198)

FIgure 2

Wall

Gasket

Mounting Bracket

Routing Cable

Cap

Nut

External Speaker Connections

Ferrite Core

As close as possible

Routing Cable or

CT-100 Extension Cable

Ferrite Core

Snap together

External Speaker

Connections

YAESU MUSEN CO., LTD.

Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan

YAESU USA

6125 Phyllis Drive, Cypress, CA 90630, U.S.A.

YAESU UK

Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.

1506Y-GO

This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference including
received, interference that may cause undesired operation.

Owner’s Manual

The details of the installation and operation of the RAM3 (CMP30) is included
in the owner ’s manual of the compatible xed mount radio, or it can be down­loaded at www.standardhorizon.com. If you have any questions or comments,
please contact Standard Horizon Marine Product Support at 800/7

67-2450.

NOTE

Caution!: Before cutting the cable, it must be disconnected from the rear panel of

the transceiver.

The routing cable can be cut and spliced, however care needs to be taken
when reconnecting the wires to ensure water integrity.
After cutting you will notice there are the following wires:
Yellow, Green, Brown, Purple, Blue, Green, Red, and Shield





The Red and Shield wires are wrapped in foil. Remove the foil, and sepa­rate the Red and Shield wires.

1

2

3 4 5

EAG36X104

optIonal accessorIes

ct-100 23Ft extensIon cable

mls-310 10 watt amplIFIed speaker

mls-300 external loud speaker

specIFIcatIons

Supply voltage: 13.8 VDC (Supplied from the transceiver)
Current consumption: 700 mA @VOL Max.

200 mA @AF Mute

Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C)
MIC. Sensitivity (Typical): 60 mVrms

@ 1 kHz Tone with 3 kHz Deviation
MIC. Impedance: 2 k



AF output: 300 mW @ 16  for 10 % THD
(Internal Speaker)

2 W @ 4  for 10 % THD
(External Speaker)

Display Size: 1.8” x 0.9” (45 x 23 mm)
Display Resolution: 132 x 64 dot
Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
Weight (Approx): 11.6 oz (330g)

Disposal of your Electronic and Electric Equipment

Products with the symbol (crossed-out wheeled bin) cannot be disposed as
household waste.

Electronic and Electric Equipment should be recycled at a facility
capable of handling these items and their waste byproducts.

In EU countries, please contact your local equipment supplier
representative or service center for information about the waste
collection system in your country.

RAM3 (CMP30) controls

[H/L] Key

Press this key to toggle the transmit power between high and low. When the [H/L]

key is pressed while the transceiver is on channel 13 or 67, the power will temporarily
switch from LOW to HI power until the PTT is released. The [H/L] key does not function
on transmit inhibited and low power only channels.

PTT (Push-To-Talk) Key

Press this key to activate the transmission.

POWER

(

)

Key

Press and hold down this key to turn to the transceiver and RAM3 (CMP30) “on” and

“off”.

Microphone

The internal microphone is located here.
When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from

the small mic hole. Speak slowly and clearly into the microphone.

DISPLAY

Channel display.

SOFT KEY

For details, refer to “Mode Setting and Setup” above.

KEY PAD

[CALL/MENU] Key

Press this key to access the DSC OPERATION menu.
Press and hold this key to access the SETUP menu.

[

16/9] Key

First press: channel 16 is immediately selected.
Second press: recalls the last selected channel.
Press and hold: selects channel 9.

[](UP)/[](

DOWN) Key

These keys are used to select channels, adjust the volume and squelch level, and to

choose DSC calls, DSC setup and Radio setup function.

[VOL/SQ] Key (Volume Control / Squelch Control

)

Press this key to toggle the function of the microphone’s

[]

or

[]

key between the

channel selections, volume level adjustment, and squelch level adjustment.

[CLR/WX] Key
For details, refer to “Mode Setting and Setup” above.

[ENT] Key

This key functions as the enter key.

Speaker

The internal speaker is located here.

[DISTRESS] KEY

This key is used to send a DSC Distress Call.
Lift the red spring loaded DISTRESS cover, then press and hold in the [DISTRESS]

key.

⑤

①
②

③
④

⑥

⑦

⑧

⑨

Yaesu UK Ltd

Unit 12, Sun Valley Business Park
Winnall Close
Winchester SO23 OLB
United Kingdom
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Declaration of Conformity

Nr. YUK-DOC-0807-15

We, Yaesu UK Ltd. certify and declare under our sole responsibility that the following
equipment complies with the essential requirements of the Directive 1999/5/EC and
2011/65/EU.

Type of Equipment Remote Station Microphone
Brand Name STANDARD HORIZON
Model Number CMP30
Manufacturer YAESU MUSEN Co. LTD
Address of Manufacturer Tennozu Parkside Building 2-5-8 Higashi-Shinagawa,

Shinagawa-ku, Tokyo 140-0002, JAPAN

Applicable Standards:
This equipment is tested to and conforms to the essential requirements of directive, as included
in following standards:

EMC 1999/5/EC Art. 3 (1) (b)

EN 301 843-01 V1.3.1
EN 301 843-02 V1.2.1

Safety 1999/5/EC Art. 3 (1) (a)

EN 60950-1:2006+A2:2013

RoHS2 2011/65/EU Art. 7 (b)

EN 50581:2012

The technical documentation as required by the Conformity Assessment procedures is kept at
the following address:

Company: Yaesu UK Ltd
Address: Unit 12, Sun Valley Business Park, Winnall Close,

Winchester, Hampshire, UK, SO23 0LB

Technical Construction File: Issued by Yaesu Musen Co. Ltd., Tokyo, Japan

File No. YETA000154A

Drawn up in: Winchester, Hampshire UK

Date: 11th August 2015

Name and position: PCJ Bigwood,

Technical Sales Manager