Standart Horizon RAM3, CMP30 Owner's Manual

RAM3 (CMP30
)
Remote Station Microphone
The RAM3 (CMP30) allows you to remotely control all functions of Standard Hori-
zon xed mount VHF radios which include GX1600, GX1700, GX2000, GX2100, GX2150, GX2200, GX5000S and GX5500S. The full dot matrix display and pro­grammable keys make operation simple and fast. Additional features include turning the radio on/off and all DSC functions including Distress. The RAM3 (CMP30) can be extended up to 70 feet using the optional CT-100 (23 Foot) extension cable. The
RAM3 (CMP30) is backed by an industry leading 3-year waterproof warranty.
WARNING: Do not connect or remove the CMP30 (RAM3) microphone while
the radio is powered on. This may result in equipment failure.
1. Connect the Extension Cable to the 8-pin connector on the transceivers rear panel, then tighten the Cable Nut (Figure 1).
2. Referring to Figure 2, attach the supplied ferrite core as close as possible to the MIC plug of the Routing Cable and External Speaker Connections, then snap its two halves together. And then, wind some plastic tape around the ferrite core, to prevent vibration from causing the two halves to split apart and fall off the wires.
3. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall then insert the Exten­sion Cable into this hole. Connect the Gasket and Mount Base to the Extension Cable Connector using the Nut.
4. Drill the four Screw holes (approx. 2 mm) on the wall then install the Mounting Bracket to the wall using four screws.
5. Put the Rubber Cap on to the Nut.
6. The installation is now complete. Connect the RAM3 (CMP30) to the Extension Cable Connector and tighten the Cable Nut.
RAM3 (CMP30) InstallatIon
FIgure 1
FIgure 3
Copyright 2015 YAESU MUSEN CO., LTD. All rights reserved.
No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD.
Included accessorIes and replacement part numbers
1. 23-Foot Routing Cable (S8101512)
2. Rubber Cap (RA052520A)
3. Mounting Bracket (RA052510) & Screws (U24312020 x 4 pcs)
4. Microphone Hanger (RA0458800: Black or RA0436000: White) &
Screws (U40412220 x 2 pcs)
5. Ferrite Core (L9190198)
FIgure 2
Wall
Gasket
Mounting Bracket
Routing Cable
Cap
Nut
External Speaker Connections
Ferrite Core
As close as possible
Routing Cable or
CT-100 Extension Cable
Ferrite Core
Snap together
External Speaker
Connections
YAESU MUSEN CO., LTD.
Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.
1506Y-GO
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference including received, interference that may cause undesired operation.
Owner’s Manual
The details of the installation and operation of the RAM3 (CMP30) is included in the owner ’s manual of the compatible xed mount radio, or it can be down­loaded at www.standardhorizon.com. If you have any questions or comments, please contact Standard Horizon Marine Product Support at 800/7
67-2450.
NOTE
Caution!: Before cutting the cable, it must be disconnected from the rear panel of
the transceiver.
The routing cable can be cut and spliced, however care needs to be taken when reconnecting the wires to ensure water integrity. After cutting you will notice there are the following wires: Yellow, Green, Brown, Purple, Blue, Green, Red, and Shield

The Red and Shield wires are wrapped in foil. Remove the foil, and sepa­rate the Red and Shield wires.
1
2
3 4 5
EAG36X104
optIonal accessorIes
ct-100 23Ft extensIon cable
mls-310 10 watt amplIFIed speaker
mls-300 external loud speaker
specIFIcatIons
Supply voltage: 13.8 VDC (Supplied from the transceiver) Current consumption: 700 mA @VOL Max.
200 mA @AF Mute
Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C) MIC. Sensitivity (Typical): 60 mVrms
@ 1 kHz Tone with 3 kHz Deviation MIC. Impedance: 2 k
AF output: 300 mW @ 16  for 10 % THD (Internal Speaker)
2 W @ 4  for 10 % THD (External Speaker)
Display Size: 1.8” x 0.9” (45 x 23 mm) Display Resolution: 132 x 64 dot Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm) Weight (Approx): 11.6 oz (330g)
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste byproducts.
In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.
RAM3 (CMP30) controls
[H/L] Key
Press this key to toggle the transmit power between high and low. When the [H/L]
key is pressed while the transceiver is on channel 13 or 67, the power will temporarily switch from LOW to HI power until the PTT is released. The [H/L] key does not function on transmit inhibited and low power only channels.
PTT (Push-To-Talk) Key
Press this key to activate the transmission.
POWER
(
)
Key
Press and hold down this key to turn to the transceiver and RAM3 (CMP30) “on” and
“off”.
Microphone
The internal microphone is located here. When transmitting, position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm) away from
the small mic hole. Speak slowly and clearly into the microphone.
DISPLAY
Channel display.
SOFT KEY
For details, refer to “Mode Setting and Setup” above.
KEY PAD
[CALL/MENU] Key
Press this key to access the DSC OPERATION menu. Press and hold this key to access the SETUP menu.
[
16/9] Key
First press: channel 16 is immediately selected. Second press: recalls the last selected channel. Press and hold: selects channel 9.
[](UP)/[](
DOWN) Key
These keys are used to select channels, adjust the volume and squelch level, and to
choose DSC calls, DSC setup and Radio setup function.
[VOL/SQ] Key (Volume Control / Squelch Control
)
Press this key to toggle the function of the microphone’s
[]
or
[]
key between the
channel selections, volume level adjustment, and squelch level adjustment.
[CLR/WX] Key For details, refer to “Mode Setting and Setup” above.
[ENT] Key
This key functions as the enter key.
Speaker
The internal speaker is located here.
[DISTRESS] KEY
This key is used to send a DSC Distress Call. Lift the red spring loaded DISTRESS cover, then press and hold in the [DISTRESS]
key.
① ②
③ ④
Yaesu UK Ltd
Unit 12, Sun Valley Business Park Winnall Close Winchester SO23 OLB United Kingdom Tel: +44 (0)1962 866667 Fax: +44 (0)1962 856801 Email: sales@yaesu.co.uk
Declaration of Conformity
Nr. YUK-DOC-0807-15
We, Yaesu UK Ltd. certify and declare under our sole responsibility that the following equipment complies with the essential requirements of the Directive 1999/5/EC and 2011/65/EU.
Type of Equipment Remote Station Microphone Brand Name STANDARD HORIZON Model Number CMP30 Manufacturer YAESU MUSEN Co. LTD Address of Manufacturer Tennozu Parkside Building 2-5-8 Higashi-Shinagawa,
Shinagawa-ku, Tokyo 140-0002, JAPAN
Applicable Standards: This equipment is tested to and conforms to the essential requirements of directive, as included in following standards:
EMC 1999/5/EC Art. 3 (1) (b)
EN 301 843-01 V1.3.1 EN 301 843-02 V1.2.1
Safety 1999/5/EC Art. 3 (1) (a)
EN 60950-1:2006+A2:2013
RoHS2 2011/65/EU Art. 7 (b)
EN 50581:2012
The technical documentation as required by the Conformity Assessment procedures is kept at the following address:
Company: Yaesu UK Ltd Address: Unit 12, Sun Valley Business Park, Winnall Close,
Winchester, Hampshire, UK, SO23 0LB
Technical Construction File: Issued by Yaesu Musen Co. Ltd., Tokyo, Japan
File No. YETA000154A
Drawn up in: Winchester, Hampshire UK
Date: 11th August 2015
Name and position: PCJ Bigwood,
Technical Sales Manager
Loading...