Standalone Keypad Access Control User Manual

Standalone Keypad Access Control

User Manual

Please read the manual carefully before use this unit

1. Packing List

Name Quantity Remarks

Keypad 1

User manual 1

Screw driver 1

Rubber plug 2

Self tapping screws 2

Star screws

Please ensure that all the above contents are correct. If any are missing please notify the

supplier of the unit.

1

Φ20mm×60mm,Special for keypad

Φ6mm×30 mm

Φ4mm×28 mm

Φ3mm×6mm,

, used for fixing

, used for fixing

used for fixing

2. Quick Reference Programming Guide

To enter the programming mode

To exit from the programming mode *

Note that to undertake the following programming the master user must be logged in

To change the master code

To add a PIN user.

To add a card user 1 Read Card #

*

Master code

999999 is the default factory master code

0

New code

The master code can be 6 to 8 digits

1

User ID number # PIN #

The ID number is any number between 1 & 2000. The

PIN is any four digits between 0000 & 9999 with the

exception of 1234 which is reserved. Users can be added

continuously without exiting programming mode

Cards can be added continuously without exiting

programming mode

#

#

New code

#

To delete a PIN or a card user. 2 User ID number # for a PIN user or

2 Read Card # for a card user

Users can be deleted continuously without exiting

programming mode

To unlock the door for a PIN user Enter the PIN then press #

To unlock the door for a card user Present the card

3. Description

The unit is single door multifunction standalone access controller or a Wiegand output

keypad or card reader. It is suitable for mounting either indoor or outdoor in harsh

environments. It is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated

case which is available in either a bright silver or matt silver finish. The electronics are

fully potted so the unit is waterproof and conforms to IP68. This unit supports up to 2000

users in either a Card, 4 digit PIN, or a Card + PIN option. The inbuilt card reader supports

125KHZ EM cards,13.56MHz Mifare cards. The unit has many extra features including

lock output current short circuit protection, Wiegand output , and a backlit keypad. These

features make the unit an ideal choice for door access not only for small shops and

domestic households but also for commercial and industrial applications such as factories,

2

warehouses, laboratories, banks and prisons.

4. Features

 Waterproof, conforms to IP68

 Strong Zinc Alloy Electroplated anti-vandal case

 Full programming from the keypad

 2000 uses, supports Card, PIN, Card + PIN

 Can be used as a stand alone keypad

 Backlight keys

 Wiegand 26 input for connection to external reader

 Wiegand 26 output for connection to a controller

 Adjustable Door Output time, Alarm time, Door Open time

 Very low power consumption (30mA)

 Fast operating speed, <20ms with 2000 users

 Lock output current short circuit protection

 Easy to install and program

 Built in light dependent resistor (LDR) for anti tamper

 Built in buzzer

 Red, Yellow and Green LEDS display the working status

5. Specifications

Operating Voltage

User Capacity 2000

Card Reading Distance 3-6 cm

Active Current ＜60mA

Idle Current 25±5 mA

Lock Output Load Max 3A

Alarm Output Load Max 20A

Operating Temperature -45℃～60℃

Operating Humidity 10%- 90% RH

Waterproof Conforms to IP68

Adjustable Door Relay time 0 -99 seconds

Adjustable Alarm Time 0- 3 minutes

Wiegand Interface Wiegand 26 bit

Wiring Connections Electric Lock, Exit Button, External Alarm,External reader

DC 12V

±10%

6. Installation

 Remove the back cover from the keypad using the supplied special screw driver

 Drill 2 holes on the wall for the Self tapping screws and I hole for the cable

 Put the supplied rubber bungs to into the two holes

3

 Fix the back cover firmly on the wall with 2 Self tapping screws

 Thread the cable through the cable hole



Attach the keypad to the back cover.

4