Standa 11UNO User Manual

USER MANUAL

11UNO

Power Monitor

11UNO User’s Manual Revision 6 1

WARRANTY

The Standa 11UNO Single Channel Laser Power, Energy and Power/Energy Meter carries a one-year
warranty (from date of shipment) against material and/or workmanship defects, when used under normal
operating conditions. The warranty does not cover damages related to battery leakage or misuse.

Standa will repair or replace, optionally, any 11UNO that proves to be defective during the warranty period,
except in the case of product misuse.

Any attempt by an unauthorized person to alter or repair the product voids the warranty.
The manufacturer is not liable for consequential damages of any kind.
Customers must fill in and mail the warranty card in order to activate the warranty.
In case of malfunction, contact your local Standa distributor Standa office to obtain a return authorization

number. The material should be returned to:

Standa Ltd.

Svitrigailos 4-39

03222 Vilnius

Lithuania

Tel: [phone]

Fax: [phone]

e-mail: [e-mail]

Website: www.standa.LT

CLAIMS

To obtain warranty service, contact Standa or send the product, with a description of the problem,
transportation and insurance prepaid, to the Standa. Standa assumes no risk for the damage in transit.
Standa will, at its option, repair or replace the defective product free of charge or refund your purchase
price. However, if Standa determines that the failure is caused by misuse, alterations, accident or
abnormal condition of operation or handling, you will be billed for the repair and the repaired product will
be returned to you, transportation prepaid.

Standa Ltd. All rights reserved

11UNO User’s Manual Revision 6 2

SAFETY INFORMATION

Do not use the 11UNO if the device or the detector looks damaged, or if you suspect that the 11UNO is
not operating properly.

Appropriate installation must be done for water-cooled and fan-cooled detectors. Refer to the specific
instructions for more information. The user must wait for a while before handling these detectors after
power is applied. Surfaces of the detectors get very hot and there is a risk of injury if they are not allowed
to cool down.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, it is
suggested to try to correct the interference by taking one or more of the following steps:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment to an outlet that is on a different circuit than the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved in writing by Standa may void the

user’s authority to operate this equipment.

Standa Ltd. All rights reserved

11UNO User’s Manual Revision 6 3

TABLE OF CONTENTS

1.1 INTRODUCTION ............................................................................................................................................... 4

1.2 SPECIFICATIONS .............................................................................................................................................. 5

1.3 FRONT PANEL DESCRIPTION ........................................................................................................................... 6

1.4 CONNECTOR DESCRIPTION ............................................................................................................................. 7

2.1 POWER MEASUREMENT PROCEDURE ............................................................................................................... 7

2.2 DISPLAY DESCRIPTION .................................................................................................................................... 9

3.1 BATTERY SELECTION ................................ ................................................................................................ .... 10

3.2 BATTERY INSTALLATION ............................................................................................................................... 10

3.3 BATTERY REMOVAL ...................................................................................................................................... 10

DECLARATION OF CONFORMITY .................................................................................................................... 11

3.4 RECYCLING AND SEPARATION PROCEDURE ................................................................................................... 12

3.5 SEPARATION ................................................................................................................................................. 12

3.6 DISMANTLING PROCEDURE ........................................................................................................................... 12

LIST OF ILLUSTRATIONS

FIG. 1-1 11UNO FRONT PANEL ...................................................................................................................... 6

FIG. 1-2 11UNO CONNECTORS ...................................................................................................................... 7

FIG. 1-3 11UNO LCD DISPLAY ....................................................................................................................... 9

Standa Ltd. All rights reserved