Stamina Orbital Rower 1215, 1215 Owner's Manual

35-1215

STAMINA PRODUCTS

MADE IN TAIWAN

Product May Vary Slightly

From Pictured.

2008, 07

Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

When calling for parts or
service, please specify the
following number.

WA RNING

CAUTION:
Weight on this product should not exceed 250 lbs.

2008 Stamina Products, Inc.

Owner's Manual

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

This Product is Produced Exclusively by

TABLE OF CONTENTS

Conditioning Guidelines 14
Warm-up a nd Cool-Down 15
Product Parts Drawing 16
Parts List 17
Warranty 19
Notes 20
Fax/Mail Ordering Form 22

Page Page

Safety Instructions 2
Before Y ou Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Operational Instructions 11
Storage 13
Maintenance 13

Read all warnings posted on the 1215 Orbital Rower.
Read this Owner's Manual and follow it carefully before using the 1215 Orbital Rower. Make sure
that it is properly assembled and tightened before use.
We recommend that two people be available for assembly of this product.
Keep children away from the 1215 Orbital Rower. Do not allow children to use or play on the 1215
Orbital Rower. Kee p children and pets away from the 1215 Orbital Rower when it is in use.
It is recommended that you place this exercise equipment on an equipment mat.
Set up and operate the 1215 Orbital Rower on a solid level surface. Do not position the 1215
Orbital Rower on loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the 1215 Orbital Rower.
Inspect the 1215 Orbital Rower for worn or loose components prior to use.
Tighten/replace any loose or worn components prior to using the 1215 Orbital Rower.
Shocks on rowers get HOT during use. To avoid burns, do not touch the shock until it has time to
cool.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the 1215 Orbital Rower.
Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or
crosstraining shoes. Be sure that they fit well, provide foot support and feature non-skid rubber
soles.
Be careful to maintain your balance while using, mounting, dismounting, or assembling the 1215
Orbital Rower, loss of balance may result in a fall and serious bodily in jury.
Do not use the seat to move the 1215 Orbital Rower. The Seat will move and the Seat Carriage
may pinch your hand or fingers.
The 1215 Orbital Rower should not be used by persons weighing over 250 pounds.
The 1215 Orbital Rower should be used by only one person at a time.
The 1215 Orbital Rower is for consumer use only. It is not for use in public or semipublic facilitie s.

SAFETY INSTRUCTIONS

To reduce the risk of serious injury, read the following Safety Instructions before
using the 1215 Orbital Rower.

WARNING:

Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is e specially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

WARNING:

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

2

THANK YOU FOR PURCHASING THE

1215 Orbital Rower

To help you get started, we have pre-assembled most of your

1215 Orbital Rower at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into sha pe

and on your way to achieving a happier and healthier lifestyle.

3

Should you have any que stions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

CALL US FIRST

Customer Service

1(800) 375-7520

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

BEFORE YOU BEGIN

4

Thank you for choosing the 1215 Orbital Rower.
W e take gre at pride in producing this quality product
and hope it will provide ma ny hours of quality exercise
to make you feel better, look better and enjoy life to
its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. Th e 1215 Orbital Rower
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and fa mili arize yoursel f with the parts that are
labeled.
Read this manual carefully before using the 1215

Orbital Rower.

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your 1215 Orbital Rower,
plea se do not return the product. Conta ct us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T ime) on Friday.
If you would like to contact us online, go to our
website at www.sta mina products.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Phillips Screwdriver

Adjustable Wrench

Adjustable Wrench

Rear

Support

Endcap

Seat

Left Handlebar

Shock

Locking Knob

Left Base Frame

Foam Grip

Pedal Strap

Meter

Pedal

Endcap

Shock

Locking Knob

Right Base Frame

Center Beam

Pull Pin

Foam Grip

Right
Handlebar

Pivot Support

Warning

Label

Shock Decal

Shock Decal

5

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the 1215 Orbital Rower. Ple a se take a
moment to fa miliarize yourself with all of the warning & notice labels.

Label is larger tha n actual size

WAR NING LABEL(54)

W1

SHOCK DECAL(18)

D1

(2 locations)

6

Part No. and Description Qty

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
ends of the bolts, or screws on the circles to check for the correct di a meter . Use the small scale to check the
length of the bolts and screws.

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

mm.

in.

INCHES

MILLIMETERS

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

6 8 10 12

3/16" 5/16" 1/2"3/8"1/4"

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

43 Bolt, Hex Head (M8 x 1.25 x 16mm) 8

44 Bolt, Hex Head (M8 x 1.25 x 40mm) 4
45 Bolt, Hex Head (M8 x 1.25 x 55mm) 2

46 Bolt, Hex Head (M10 x 1.5 x 95mm) 1

48 Screw, Round He ad (M4 x 10mm) 2

51 Nylock Nut (M8 x 1.25) 6
52 Nylock Nut (M10 x 1.25) 1

53 Acorn Nut (M10 x 1.25) 2

55 Lock Washer (M8) 8
56 Lock Washer (M10) 2

57 Washer (M8) 6
58 Washer (M10) 2

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als
until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part please call
our toll-free number for assistance 1 [phone] or e-mail us at:

[e-mail]

7

STEP 1

Insert the PEDAL SHAFT(21) through holes located on the front end of the CENTER BEAM(1). Place a
SP ACER(22) a nd a PEDAL(23) onto ea ch end of the PEDAL SHAFT(21) and slide them toward the CENTER
BEAM(1). Then secure the PEDALS(23) with WASHERS(M10)(58), LOCK WASHERS (M10)(56), and
ACORN NUTS(M10x1.5)(53) at both sides of the PEDAL SHAFT(21).
NOTE:

STEP 2

Insert the PEDAL STRAPS(24) into the slots in the bottom of the PEDALS(23). When feet are in the
PEDALS(23), the ends of the PEDAL STRAPS(24) will be facing away from the CENTER BEAM(1) as

shown above.

You need to use two Wrenches to tighten the ACORN NUTS(M10x1.5)(53) at both ends of the
PEDAL SHAFT(21) at the same time.

ASSEMBLY INSTRUCTIONS

8

NOTE: Lay your partially assembled 1215 Orbital Rower up side down to complete STEP 3 and 4.

STEP 3

Place the LEFT and RIGHT BASE FRAME(2, 3) onto the CENTER BEAM(1). Connect the LEFT and
RIGHT BASE FRAME(2, 3) together with the two MOUNTING BRACKETS(4), then secure with HEX
BOLTS(M8x1.25x16mm)(43) and LOCK W ASHERS(M8)(55).

STEP 4

Attach the REAR SUPPORT(16) to the SUPPORT BRACKET(15) with HEX BOLT(M10x1.5x95mm)(46)
and NYLOCK NUT(M10x1.5)(52). Lock the REAR SUPPORT(16) in position by inserting the PULLING
PIN(17) through the holes in the SUPPORT BRACKET(15) and REAR SUPPORT(16).

ASSEMBLY INSTRUCTIONS

9

STEP 5

Attach the LEFT HANDLEBAR(8) to the bracket located on the rear of the LEFT BASE FRAME(2) with
HEX BOL T(M8x1.25x55mm)(45), WASHER(M8)(57), and NYLOCK NUT(M8x1.25)(51).

STEP 6

Attach the SHOCK(14) to the bracket located on the front of the LEFT BASE FRAME(2) with HEX BOLT
(M8x1.25x40mm)(44), WASHER(M8)(57), and NYLOCK NUT(M8x1.25)(51). Make sure you assembled
the shock allowing the shock to extend toward the LEFT HANDLEBAR(8). Connect the other end of the
SHOCK(14) to the TENSION ADJUSTER(12) with HEX BOL T (M8x1.25x40mm)(44), WASHER(M8)(57),

and NYLOCK NUT(M8x1.25)(51).
Repeat the above to attach the RIGHT HANDLEBAR(9) and SHOCK(14) to the RIGHT BASE FRAME(3).

ASSEMBLY INSTRUCTIONS

10

STEP 7

Slide the SEAT(25) onto the CENTER BEAM(1). Insert the STOPPER BOLT(20) through the CENTER
BEAM(1) and lock in position by screwing on the STOPPER(19). Also, plea se verify that the other STOPPER
BOLT(20) and STOPPER(19) are assembled at the factory. Press the CENTER BEAM CAP(28) into the
back end of the CENTER BEAM(1).

STEP 8

Pry the METER(30) from the CONSOLE(31). Attach the CONSOLE(31) to the CENTER BEAM(1) with
ROUND HEAD SCREWS(M4x10mm)(48).

STEP 9

Install a AA battery into the METER(30), one battery included. See page 12 for detailed battery installation
instructions. Run the connection wire of the METER(30) through the square hole on the CONSOLE(31).
Place the METER(30) back into the CONSOLE(31). Plug the connection wire of the METER(30) into the
socket located at the front end of the CENTER BEAM(1).

(Assembled at the factory)

OPERATIONAL INSTRUCTIONS

11

The shocks get HOT after a few minutes of use. To avoid burns, do not touch the shock until it
ha s time to cool.

NOTE: Tighten LOCKING KNOBS(13) securely before using the 1215 Orbital Rower.
CAUTION:

A. B.

LOAD ADJUSTMENT

The resistance of the shocks can be adjusted by sliding the TENSION ADJUSTERS(12) to change the
position on the HANDLEBARS(8, 9). The lowest position will provide the lowest resistance, the upper
position will provide the higher resistance.
Loosen the LOCKING KNOB(13) and slide the TENSION ADJUSTER(12) to aspired position. Tighten the

LOCKING KNOB(13) after adjusting. Use the number marks on the HANDLEBARS(8, 9) to help set the
TENSION ADJUSTER(12) at the same height on both sides.

TO ADJUST THE REAR SUPPORT(16)

Pull out the PULL PIN(17) from the SUPPORT BRACKET(15). Fold the REAR SUPPORT(16) forward,
then you can set the 1215 Orbital Rower flat on the floor. Lock the SUPPORT BRACKET(15) in the flat
position by inserting the PULL PIN(17) ba ck into the SUPPORT BRACKET(15). Refer to illustration B.
The seat can slide freely when the 1215 Orbital Rower is in the flat position. In the incline position as
shown in illustration A, there will be more resistance as you slide backward, less resistance as you slide
forward.

12

FUNCTION BUTTON:

Press the button to select functions. Reset all functions to zero
by pressing the button and holding it down for four seconds.

FUNCTION MARKS ( On The Display ) :

POWER OFF :

POWER ON :

Seat movement or push the BUTTON.
Automatic shut off after 4 minutes of ina ctivity .

Scan
Speed
Distance
Timer

A :
S :

D :

T :

Count
Calories
Mile
Signal Mark

CO :

CA :

M :

:

SCAN:

SPEED:

DISTANCE:

TIMER:

COUNT:

CALORIES:

Press the button until "A" a ppears in the display. Automatically scans SPEED, DISTANCE,
TIMER, COUNT, and CALORIES in sequence with change every 4 se conds.

Press the button until "S" appears to display the current speed, from zero to 71 MPH.

Press the button until "D" appears to display the distance you have traveled, from zero to

999.9 miles.

Press the button until "T" appe ars to display the rowing time, from one second up to 99:59
minutes.

Press the button until "CO" appears to display the total number of rows you have taken,
from zero to 9999 rows.

Press the button until "CA" a ppe ars to display the calorie consumption, from zero to 999.9
K cal.
The calorie readout is a n estimate for a n average user . It should be used only as a comparison
between workouts on this unit.

FUNCTIONS:

HOW TO INSTALL AND REPLACE BATTERY:

Use hand or simple tool to pry the METER(30) from the CONSOLE
(31).

The meter operates with an AA battery. Refer to the illustration to
install or replace the battery.

1.

2.

Rechargeable batteries are not recommended.1.

NOTE:

AA Battery

USING THE METER

OPERATIONAL INSTRUCTIONS

13

STORAGE

To store the 1215 Orbital Rower simply keep it in a clean dry place.
Fold The REAR SUPPORT(16) for easy storage, refer to page 11.
Grasp the Front and Rear Stabilizer to move the 1215 Orbital Rower. Do not use the Seat to move the
1215 Orbital Rower. The Seat will move and the Seat Carriage may pinch your hand or fingers.
To avoid damage to the electronics, remove the battery before storing the 1215 Orbital Rower for one
year or more.

1.

2.

3.

4.

MAINTENANCE

The safety and integrity designed into the 1215 Orbital Rower can only be maintained when the 1215
Orbital Rower is regularly exa mined for da mage and wea r. Speci al attention should be given to the following:

Pull on the HANDLEBARS(8, 9) and verify that the SHOCKS(14) provide tension. The SHOCKS(14)
should provide many years of use.
Clean the roller tracks in the CENTER BEAM(1) with a n absorbent cloth.
Verify that the Warning Label is in place and easy to read. Call Stamina Products immediately
(1-800-375-7520) for a replacement W arning Label if the Warning Label is missing or damaged.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Verify that that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts.
Worn or da maged components shall be replaced immediately or the 1215 Orbital Rower removed from
service until repair is made.
Only Sta mina Products supplied components shall be used to maintain/repair the 1215 Orbital Rower.
Keep your 1215 Orbital Rower clean by wiping with an absorbent cloth after use.

1.

2.

3.

4.

5.

6.

7.

8.

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually, too, by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone f or a few minutes; however, your aerobic
ca pa city will i mprove over the next six to eight week s. It is important to pace yourself while you exercise so
you don't tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingers on your wrist and ta ke a six second heartbe at count. Multiply the results
by ten to find your heart rate. For exa mple, if your six se cond heartbeat count
is 14, your heart rate is 140 beats per minute. A six second count is used
because your heart rate will drop ra pidly when you stop exercising. Adjust the
intensity of your exercise until your heart rate is at the proper level.

wrist pulse

Have your doctor review your training and diet programs.
Begin your training progra m slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.

Target Heart Rate Zone Estimated by Age*

Remember to follow these e ssentials:

To determine if you are working out at the correct intensity, use a heart rate monitor or use the ta ble below .
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting a n exercise program, work out at the low end of your target heart
rate zone. As your a erobic ca pa city improves, gradually incre a se the intensity of your workout by increa sing
your heart rate.

For cardiorespiratory training benefits, the American College of Sports Medicine re commends working
out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate

*

20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute

200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

14

15

WARM-UP and COOL-DOWN

Warm-Up The purpose of warming up is to prepare your body f or exercise and to mini mize injuries. W arm

up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your
heart rate and warm the working muscle s. Activities may include brisk walking, jogging, jumping ja ck s, jump
rope, and running in place

Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength

or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevated temperature, which greatly reduces the risk of in jury . Stretches should be held for 15 to 30 seconds.
Do not bounce.

Suggested Stretching Exercise s

Remember always to check with your physician before starting any exercise program.

Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state

at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to
return to the heart. Your cool-down should include the stretches listed above and should be completed after
each strength-training session.

Lower Body Stretch

Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.

Floor Stretch

While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder­width a part and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the floor,
have legs apart one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

PRODUCT PARTS DRAWING

16

FRONT

BACK

PARTS LIST

DIAGRAM# PART NAME QTY

17

1 Center Beam 1
2 Left Base Frame 1
3 Right Base Frame 1
4 Mounting Bracket 2
5 Pivot Support 2
6 Bushing 4
7 Shaft Tube 2
8 Left Handlebar 1
9 Right Handlebar 1
10 Bushing 4
11 Foam Grip 2
12 Tension Adjuster 2
13 Locking Knob 2
14 Shock 2
15 Support Bracket 1
16 Rear Support 1
17 Pull Pin 1
18 Shock Decal 2
19 Stopper 2
20 Stopper Bolt 2
21 Pedal Shaft 1
22 Spacer 2
23 Pedal 2
24 Pedal Strap 2
25 Seat 1
26 Seat Carriage 1
27 Roller 4
28 Center Beam Cap 1
29 Center Beam Cap /with hole 1
30 Meter 1
31 Console 1
32 Sensor Wire 1
33 Thin Nut 1
34 Foam Block 1
35 Magnet 1
36 Endcap (50.8mm) 2
37 Endcap (60mm) 2
38 Round Plug (25mm) 2
39 Round Plug (50mm) 2
40 Carriage Bolt (M8 x 1.25 x 45mm) 2
41 Bolt, Button Head (M8 x 1.25 x 25mm) 4
42 Bolt, Flat Head (M8 x 1.25 x 25mm) 4
43 Bolt, Hex Head (M8 x 1.25 x 16mm) 8
44 Bolt, Hex Head (M8 x 1.25 x 40mm) 4
45 Bolt, Hex Head (M8 x 1.25 x 55mm) 2
46 Bolt, Hex Head (M10 x 1.5 x 95mm) 1
47 Screw , Round Head (M6 x 1 x 25mm) 4

PARTS LIST

DIAGRAM# PART NAME QTY

18

48 Screw , Round Head (M4 x 10mm) 2
49 Screw , Round Head (M4 x 16mm) 2
50 Bolt, Button Head (M8 x 1.25 x 16mm) 4
51 Nylock Nut (M8 x 1.25) 10
52 Nylock Nut (M10 x 1.25) 1
53 Acorn Nut (M10 x 1.25) 2
54 Warning Label 1
55 Lock Washer (M8) 16
56 Lock Washer (M10) 2
57 Washer (M8) 18
58 Washer (M10) 2
59 Manual 1

19

WARRANTY

LIMITED WARRANTY

MODEL 35-1215

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts a nd five(5) years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, fa mily, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Stamin a Products, Inc. P .O. Box 1071, Springf ield

Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1 [phone]. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIED W ARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF
THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF ANY PART OF THE
PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED W ARRANTY OR ANY IMPLIED W ARRANTY,
THE REMEDY OF REP AIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY A V AILABLE T O YOU. In

the event that the purchaser ma kes a ny claim under this limited warra nty or any i mplied warranty , the W arrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warra ntor's premises in Springfield, Missouri. Return of the enclosed warra nty registration card is not required
for warranty coverage, but is merely a way of establishing the date and place of purchase.

Stamin a Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warra nty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers and li mitations of a nd on implied warranties a nd
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

NOTES

20

NOTES

21

IMPORT ANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORT ANT : We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reached by e mail at [e-mail] or toll free at 1-800-375-7520 (in the U.S.). Should a part
be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Time, Monday
through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below a nd fax
it to [phone]. Our Customer Service Department will be a ble to a ssist you with your problem a nd the
part will be mailed directly to your house.

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1

EXAMPLE:

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com