Stamina inLine Traction Control System, inLine 20-4800 Owner's Manual

When calling for parts or

service, please specify

the following number

:

Model#: 20-4800

CAUTION:
Weight on this product should not exceed 250 lbs.

Owner's

Manual

This Product is Distributed Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

Product May Vary Slightly From Pictured.

STAMINA PRODUCTS

MADE IN CHINA

©

2012 Stamina Products, Inc.

2012, 03

Exercise can present a
h e a l t h r i sk . Co n su l t a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
dis c o n t i n ue use of this
equipment. Serious bodily
in j u r y c a n occ u r if th is
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all in str uct ion s a re not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

!

WARNING

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Operational Instructions ........................... 12

Storage ....................................................... 15

Maintenance ............................................... 15

Product Parts Drawing .............................. 16

Parts List .................................................... 17

Warranty ..................................................... 18

Fax/Mail Ordering Form ............................ 19

SAFETY INSTRUCTIONS

2

1. Read all warnings and cautions posted on the inLine® Traction Control System.

2. The inLine® Traction Control System should only be used after a thorough review of the

Owner’s Manual.

3. We recommend that two people be available for assembly of this product.

4. Keep children away from the inLine® Traction Control System. Do not allow children to use or
play on the inLine® Traction Control System. Keep children and pets away from the inLine®
Traction Control System when it is in use.

5. It is recommended that you place this exercise equipment on an equipment mat.

6. Set up and operate the inLine® Traction Control System on a solid level surface. Do not
position the inLine® Traction Control System on loose rugs or uneven surfaces.

7. Make sure that adequate space is available for access to and around the inLine® Traction

Control System.

8. Before using, inspect the inLine® Traction Control System for worn or loose components, and
securely tighten or replace any worn or loose components prior to use.

9. Before using, always check the Main Frame(14). The Spring Pin(12) must be inserted into one of
the adjustment holes in the Inner Tube(13) and locked into position before use.

10. Co n s u l t a physicia n pr i o r to comm e n c i n g an exerci s e pr o gram and fo l l o w his/her

recommendations in developing your tness program. If at any time during exercise you feel faint,

dizzy, or experience pain, stop and consult your physician.

11. Always choose the workout which best ts your physical strength and exibility level. Know your

limits and train within them. Always use common sense when exercising.

12. Do not wear loose or dangling clothing while using the inLine® Traction Control System.

13. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or

cross training shoes that t well, provide foot support, and feature non-skid rubber soles.

14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the

inLine® Traction Control System, loss of balance may result in a fall and bodily injury.

15. The inLine® Traction Control System should not be used by persons weighing over 250

pounds.

16. The inLine® Traction Control System should be used by only one person at a time.

17. The inLine® Traction Control System is for consumer use only. It is not for use in public or

semipublic facilities.

!

WARNING

This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is

especially important if you are over the age of 35, have never exercised before,

are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in bodily injury and property damage.
To reduce the risk of serious injury, read the following Safety Instructions
before using the inLine® Traction Control System.

!

WARNING

!

CAUTION

Your

inLine® Traction Control System

does require assembly.

Please follow the assembly steps set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

3

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

To enact your warranty, please register your product

by going to register.staminaproducts.com

Call Us First

www.staminaproducts.com

1 [phone]

Customer Service

THANK YOU FOR PURCHASING THE

inLine® Traction Control System

Rear Support

Dome Endcap

Front Support

Foam Pad

Handlebar

Arm Pad

Spring Pin

Dome Endcap

Outer Tube

Cushion

Endcap

Swing Arm

Front
Stabilizer

Arm Pad

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Allen Wrench (6mm)

Wrench

Thank you for choosing the inLine® Traction

Control System. We take great pride in producing

this quality product and hope it will provide many
hours of quality exercise to make you feel better,
look better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The inLine® Traction
Control System provides a convenient and simple
method to begin your assault on getting your body
in shape and achieving a happier and healthier
lifestyle.

Befor e r e ading fu r t h er, p lease rev i e w the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the

inLine® Traction Control System.

BEFORE YOU BEGIN

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your inLine® Traction
Control System, please do not return the product.
Contact us FIRST!

If a part is missing or defective, please go to

staminaproducts.com to the Services section and

order the part needed, or call us toll free at 1-800­375-7520 (in the U.S.). Our Customer Service Staff

is available to assist you from 7:30 A.M. to 5:00 P.M.
(Central Time) Monday through Thursday and 8:00
A.M. to 3:00 P.M. (Central Time) on Friday.

Be sure to have the name and model number of

the product available when you contact us.

4

Caution Label

Foam Roller

Belt

Triangle Hook

Main Frame

Label is larger than actual size

This chart is provided to help identify the warning, caution, and notice labels on the inLine® Traction
Control System. Please take a moment to familiarize yourself with all of the warning, caution, and

notice labels.

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

CAUTION LABEL(38)C1

5

32 Acorn Nut (M8 x 1.25) 2

33 Washer (M8) 1
34 Washer (M10) 6

Part Number and Description Qty

28 Bolt, Button Head (M8 x 1.25 x 60mm) 2

35 Arc Washer (M8) 10

6

length

length

mm.

in.

INCHES

This chart is provided to help identify the hardware used in the assembly process. Place the washers or

the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to

check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

MILLIMETERS

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1/2

1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

6 8

10 12

3/16"

1/4" 5/16" 3/8" 1/2"

HARDWARE IDENTIFICATION CHART

27 Bolt, Button Head (M8 x 1.25 x 15mm) 11

29 Bolt, Button Head (M10 x 1.5 x 95mm) 2

30 Bolt, Button Head (M10 x 1.5 x 125mm) 1

31 Nylock Nut (M10 x 1.5) 3

ASSEMBLY INSTRUCTIONS

STEP 1

At tach t he FRO NT STABILIZE R(1) t o the FRONT SUPPOR T(2) w ith BUTTON HEA D BOLTS

(M8x1.25x60mm)(28), ARC WASHERS(M8)(35), and ACORN NUTS(M8x1.25)(32).

STEP 2

Insert the FR ONT SUP PORT(2) in to t he MAIN FRAME(14) and se cure wi th BUTTON HEAD

BOLTS(M8x1.25x15mm)(27), ARC WASHERS(M8)(35), and WASHER(M8)(33).

7

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Service section and order the part needed,

e-mail us at [e-mail], or call us toll free at 1-800-375-7520 (in the
U.S.). Our Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central

Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

ASSEMBLY INSTRUCTIONS

STEP 3

Attach t h e R E A R SUPPORT(10 ) t o th e FRONT SUPPO R T ( 2 ) wi th BUTTON H E A D BOLT
(M10x1.5x95mm)(29), WASHERS(M10)(34), and NYLOCK NUT(M10x1.5)(31).

STEP 4

Attach the INNER TUBE(13) to the MAIN FRAME(14) with BUTTON HEAD BOLT(M10x1.5x95mm)(29),
WASHERS(M10)(34), and NYLOCK NUT(M10x1.5)(31).

8

ASSEMBLY INSTRUCTIONS

STEP 5

Attach the SWING ARM(8) to the MAIN FRAME(14) with BUTTON HEAD BOLT(M10x1.5x125mm)(30),
WASHERS(M10)(34), and NYLOCK NUT(M10x1.5)(31).

STEP 6

In ser t t he HANDLE BAR(5) in to the SWING ARM( 8) and secure with BUTTO N HEAD BOLTS
(M8x1.25x15mm)(27), and ARC WASHERS(M8)(35).

9

ASSEMBLY INSTRUCTIONS

STEP 7

Attach the CUSHION(6) to the SWING ARM(8) with the LOCKING KNOBS(9).

STEP 8

Insert the LEFT and RIGHT ARM PAD TUBES(3, 4) into both sides of the SWING ARM(8) and lock in
position with the ADJUSTMENT KNOB(7).
NOTE: The pin of the ADJUSTMENT KNOBS(7) must be inserted into one of the adjustment holes in

the LEFT and RIGHT ARM PAD TUBES(3, 4) and use the same adjustment hole position on
both sides.

10

ASSEMBLY INSTRUCTIONS

STEP 9

Refer to the illustration below. Position the BELT(25) with its two ends to the outside. Install the
BELT(25) by attaching the TRIANGLE HOOKS(19) to the MAIN FRAME(14) with BUTTON HEAD

BOLTS(M8x1.25x15mm)(27).

11

End of belt

End of belt

HEIGHT ADJUSTMENT

OPERATIONAL INSTRUCTIONS

12

Refer to illustration A. The proper height of the
inLine® Traction Control System for stretching
is to match the pivot of the BELT(25) on the MAIN
FRAME(14) to your body pivot point at the hip.

To make a height adjustment, pull the SPRING
PIN(12) and slide the INNER TUBE(13) to adjust.
Lock the INNER TUBE(13) in desired position
by inserting the SPRING PIN(12) into one of the
adjustment holes in the INNER TUBE(13).

To use the inLine® Traction Control System, proper set up and adjustment of the inLine® Traction

Control System is important for a revitalizing stretch.

FOAM ROLLER(15) / BELT(25) ADJUSTMENT

The FOAM ROLLER(15) and BELT(25) are used to control the stretching amount and adjusts to t the
different sizes of the users. Refer to illustration B and the detail view to adjust the length of the BELT(25)
at the BUCKLES(16) on both sides.
Refer to illustration C. If you are an average height person, start with setting the

FOAM ROLLER(15)

in

the middle position of the U shaped brace of the MAIN FRAME(14) and adjust if necessary.

1. Adjust the FOAM ROLLER(15) closer to the pivot of the BELT(25) if you are taller than average or

you want to increase the amount of stretching.

2. Adjust the FOAM ROLLER(15) closer to the front edge of the MAIN FRAME(14) if you are shorter

than average or you want to reduce the amount of stretching amount.

Pivot of the

BELT(25).

A.

Pivot of the BELT(25)

Edge of the MAIN

FRAME(14)

Middle position

TOP VIEW

C.B.

13

OPERATIONAL INSTRUCTIONS

CUSHION(6) ADJUSTMENT

The position of the CUSHION(6) is adjustable. Place the
CUSHION(6) at the position which is most comfortable

for supporting your chest when stretching on the inLine®
Traction Control System.

Adjust the CUSHION(6) by loosening, but not removing,
the LOCKING KNOBS(9) and sliding the CUSHION(6) to
desired position. Tighten the LOCKING KNOBS(9) to lock
the CUSHION(6) securely.

ARM PAD(20) ADJUSTMENT

Th e width bet ween the two ARM PADS(20) must be
adjusted properly to fit the width of your upper body. The
back of your upper arms should rest on the ARM PADS(20)
during use.
To adjust, remove the ADJUSTMENT KNOBS(7) and slid
the LEFT and RIGHT ARM TUBES(3, 4) to the desired
position. Insert the pin of the ADJUSTMENT KNOBS(7)
into one of the adjustment holes in the LEFT and RIGHT
ARM PAD TUBES(3, 4) and tighten securely. Use the same
adjustment hole position on both sides.

CAUTION: Keep both feet at on the ground while stretching.

Exercise within your limits. If you feel faint or dizzy, immediately
discontinue use of this equipment.

STEP ONE: Adjust the height, rollers and waist belt as described on

pages 12 and 13. Walk into the machine until the belt ts comfortably

against your waist.

STEP TWO: Raise the two handles to bring the pad up against your

chest. Your body should t comfortably between the arm pads and the

back of your arms should rest on the pads.

STEP THREE: Slowly lean into the machine. You should feel a gentle
stretching in the spine and hamstrings. Go slowly and if needed make

adjustments to the belt in order to nd the position that allows you to

comfortably stretch and decompress your spine. Maintain a comfortable

stretching position for 2 or 3 minutes. Many people nd additional relief

by repeating this process a few times. Exhaling and breathing slowly
while performing the movement will allow your muscles to relax so you
can maximize the stretching and decompression effects.

14

OPERATIONAL INSTRUCTIONS

15

1. To store the inLine® Traction Control System, simply keep it in a clean dry place.

2. Two people are required to move the inLine® Traction Control System. One person is required

to lift the back end of the MAIN FRAME(14) and another person is required to lift the FRONT

STABILIZER(2).

STORAGE

The safety and integrity designed into the inLine® Traction Control System can only be maintained
when the inLine® Traction Control System is regularly examined for damage and wear. Special
attention should be given to the following:

1. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.

Tighten loose nuts and bolts.

2. Verify that the CAUTION LABEL(38) is in place and easy to read. Call Stamina Products immediately

at 1-800-375-7520 for a replacement CAUTION LABEL(38) if it is missing or damaged.

3. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

4. Worn or damaged components shall be replaced immediately or the inLine® Traction Control

System removed from service until repair is made.

5. Only Stamina Products supplied components shall be used to maintain/repair the inLine® Traction

Control System.

6. Keep your inLine® Traction Control System clean by wiping it off with an absorbent cloth after use.

MAINTENANCE

PRODUCT PARTS DRAWING

16

FRONT

BACK

PART# PART NAME QTY

PARTS LIST

17

1 Front Stabilizer 1
2 Front Support 1
3 Right Arm Pad Tube 1
4 Left Arm Pad Tube 1
5 Handlebar 1
6 Cushion 1
7 Adjustment Knob 2
8 Swing Arm 1
9 Locking Knob 2
10 Rear Support 1
11 Outer Tube 1
12 Spring Pin 1
13 Inner Tube 1
14 Main Frame 1
15 Foam Roller 1
16 Buckle 2
17 Bumper 1
18 Bushing 8
19 Triangle Hook 2
20 Arm Pad 2
21 Flange Plug (ø25.4mm) 2
22 Round Plug (ø25.4mm) 4
23 Endcap (ø50.8mm) 2
24 Dome Endcap (ø25.4mm) 2
25 Belt 1
26 Foam Pad 2
27 Bolt, Button Head (M8 x 1.25 x 15mm) 11
28 Bolt, Button Head (M8 x 1.25 x 60mm) 2
29 Bolt, Button Head (M10 x 1.5 x 95mm) 2
30 Bolt, Button Head (M10 x 1.5 x 125mm) 2
31 Nylock Nut (M10 x 1.5) 4
32 Acorn Nut (M8 x 1.25) 2
33 Washer (M8) 1
34 Washer (M10) 8
35 Arc Washer (M8) 10
36 Sleeve 1
37 Hand Grip 2
38 Caution Label 1
39 Allen Wrench (6mm) 1
40 Wrench 1
41 Manual 1

LIMITED WARRANTY

WARRANTY

MODEL 20-4800

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and three years on
the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL

NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health

clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the

product's use is in furtherance of a prot making enterprise, and all other use which is not for personal,

family, or household purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state

to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

18

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: .................................................................................. Purchase Price: ............................................................................................

First Name: ............................................................................................ Last Name: ...................................................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

Email Address: ....................................................................................... Phone #: ( ) ......................................................................................

Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No

*If yes, be sure your email address is included above.

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions,
please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to

417-889-8064. The part will be mailed to your address.

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

IMPORTANT : We must have your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT : Before lling out the form below make sure you have the correct information.

Refer to the parts list to make sure you're ordering the right parts!

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

Detach and Mail or Fax the Form Above

TO REGISTER YOUR PRODUCT

TO CONTACT CUSTOMER SERVICE

TO ORDER PARTS

TO CONTACT CUSTOMER SERVICE

For your co nvenience, Stamina’s customer service r epres entatives can be reached by emai l a t customerservice@
staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday

through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

TO REGISTER YOUR PRODUCT

Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071 Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model
number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your
product) ready.

If you don’t have internet access, you can call customer service at 1-800-375-7520, or ll out and mail the product registration
form below to Stamina Products, Inc.; P.O. Box 1071; Springeld, MO 65801-1071.

PRODUCT REGISTRATION FORM

TO ORDER PARTS

Detach and Mail or Fax the Form Below

PARTS ORDER FORM

PART # DESCRIPTION QUANTITY

1 Rear Unit Assembly 1

EXAMPLE: