Stamina inLINE Back Stretch Bench Pro 55-1406 Owner's Manual

Download

Page 1

CAUTION: Weight on this product should not exceed 250 lbs.

Owner's

Manual

This Product is Distributed Exclusively by

2040 N Alliance Ave, Springeld, MO 65803

Customer Care

1 (800) 375-7520

www.staminaproducts.com

Product May Vary Slightly From Pictured.

STAMINA PRODUCTS

MADE IN CHINA

2018 Stamina Products, Inc.

2018, 07

Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are securely tightened prior to each use. Follow all safety instructions in this manual.

WARNING

When calling for parts or

service, please specify

the following numbers

Model#: 55-1406

S/N: _____________

Page 2

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Storage ....................................................... 9

Maintenance ............................................... 9

Operational Instructions ........................... 9

Warranty ..................................................... 11

Product Parts Drawing .............................. 12

Parts List .................................................... 13

Notes ........................................................... 14

Fax/Mail Ordering Form ............................ 15

SAFETY INSTRUCTIONS

1. Save these instructions and ensure that other exercisers read this manual prior to using the

inLINE® Back Stretch Bench Pro for the rst time.

2. Read all warnings and cautions posted on the inLINE® Back Stretch Bench Pro.

3. The inLINE® Back Stretch Bench Pro should only be used after a thorough review of the

Owner’s Manual. Make sure that it is properly assembled and tightened before use.

4. We recommend that two people be available for assembly of this product.

5. Keep children away from the inLINE® Back Stretch Bench Pro. Do not allow children to use or play on the inLINE® Back Stretch Bench Pro. Keep children and pets away from the inLINE® Back Stretch Bench Pro when it is in use.

6. It is recommended that you place this product on an equipment mat.

7. Set up and operate the inLINE® Back Stretch Bench Pro on a solid level surface. Do not position the inLINE® Back Stretch Bench Pro on loose rugs or uneven surfaces.

8. Make sure that adequate space is available for access to and around the inLINE® Back Stretch

Bench Pro.

9. Before using, inspect the inLINE® Back Stretch Bench Pro for worn or loose components, and securely tighten or replace any worn or loose components prior to use.

10. Consult your physician before using this product. If you feel faint, dizzy, or experience pain during use, stop immediately and consult with your physician.

11. Choose the intensity that ts your strength and exibility level. Know your body's limits and use this product within them. Use common sense when using this product.

12. Do not wear loose or dangling clothing while using the inLINE® Back Stretch Bench Pro.

13. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or

cross training shoes that t well, provide foot support, and feature non-skid rubber soles.

14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the inLINE® Back Stretch Bench Pro, loss of balance may result in a fall and bodily injury.

15. The inLINE® Back Stretch Bench Pro should not be used by persons weighing over 250 pounds.

16. The inLINE® Back Stretch Bench Pro should be used by only one person at a time.

17. The inLINE® Back Stretch Bench Pro is for consumer use only. It is not for use in public or semipublic facilities.

WARNING

Cancer and Reproductive Harm www.P65Warnings.ca.gov

Consult your physician before starting this or any exercise program. This is

especially important if you are over the age of 35, have never exercised before, are pregnant, or su󰀨er from any health problem. This product is for home use

only. Do not use in institutional or commercial applications. Failure to follow all warnings and instructions could result in serious injury or death. To reduce the risk of serious injury, read the following Safety Instructions before using the inLINE® Back Stretch Bench Pro.

WARNING

Page 3

NEED HELP?

1 (800) 375-7520

customer.care@staminaproducts.com

Hi! From all of us here at Stamina Products, thank you for your purchase. We know that you have big fitness goals in mind and we are here to help you along. Call us, email us, or send us a message on Facebook. Be sure to contact us if you

have any questions on your new product. We look forward to hearing from you!

With your body in mind,

Stamina Customer Care

To enact your extended warranty and to help us better serve you, please go online and register your new product.

ONLINE

customer.care@staminaproducts.com

www.staminaproducts.com

TELEPHONE

1 (800) 375-7520

FAX

(417) 889-8064

MAIL

Stamina Products, Inc.

ATTN: Customer Care

2040 N Alliance Ave

Springfield, MO 65803

facebook.com/StaminaProducts facebook.com/AeroPilates

CUSTOMER CARE HOURS:

Monday-Thursday, 7:30 AM-5:00 PM, Central Time

Friday, 8:00 AM-3:00 PM, Central Time

It is quick and easy to register online, but if you’re a little old school or just need a reason to raise that little flag on your mailbox, fill out the info on the last page of this

manual and mail it in.

Page 4

Lever

Extending Tube

Wheels

Armpit Pad Support

Foam Pad

Cushion

Armpit Pad

Swing Arm

Armpit Pad

Support

Adjustment Knob

High Adjustment Beam

Armpit Pad

Adjustable Instep Frame

Foam Pad

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Allen Wrench (4mm)

Allen Wrench (6mm)

BEFORE YOU BEGIN

Caution Label

Endcap

Main Frame

Thank you for choosing the inLINE® Back

Stretch Bench Pro. We take great pride in

producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program

can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise. The inLINE® Back Stretch Bench Pro provides a convenient and simple method to begin your journey of getting your body in shape and achieving a happier and healthier lifestyle.

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Locate the serial decal on the product and write the serial number on the cover of the manual in the space provided. See page 5 for an image of the serial decal. Model number and serial number are required when calling for assistance.

Read this manual carefully before using the

inLINE® Back Stretch Bench Pro.

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can sometimes be missing parts or incorrectly sized parts. If you have any questions or problems with the parts included with your inLINE® Back Stretch Bench Pro, please do not return the product. Contact us FIRST!

If a part is missing or defective, please go to staminaproducts.com under the Customer Care section and order the part needed, or call us toll

free at 1-800-375-7520 (in the U.S.). Our Customer

Care Staff is available to assist you from 7:30

A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

Be sure to have the name and model number of the product available when you contact us.

Pillow

Serial Decal

Page 5

This chart is provided to help identify the warning, caution, and notice labels on the inLINE® Back Stretch Bench Pro. Please take a moment to familiarize yourself with all of the warning, caution, and

notice labels.

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

CAUTION LABEL(40)

To best serve you, our Customer Care Representatives will

need your serial number. For quick access, write in your

serial number on the cover of the manual.

SERIAL DECAL(35)

Page 6

Part Number and Description Qty

33 Bolt, Button Head (M6 x 1 x 13mm) 4 34 Bolt, Button Head (M8 x 1.25 x 22mm) 1

length

mm.

in.

INCHES

This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware may be already attached to the part.

MILLIMETERS

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

6 8 10 12

3/16" 1/4" 5/16" 3/8" 1/2"

HARDWARE IDENTIFICATION CHART

Page 7

ASSEMBLY INSTRUCTIONS

STEP 1

Slide the PILLOW(39) onto the CUSHION(12) and secure in position with the elastic band. Attach the CUSHION(12) to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M6x1x13mm)(33).

STEP 2

Push the BUTTON PIN(9) in and insert the ARMPIT PAD SUPPORT(7) into the SWING ARM(6). Slide an ARMPIT PAD(8) on the ARMPIT PAD SUPPORT(7). Repeat on other side.

NOTE: There are three adjustment holes in the bottom of the SWING ARM(6) which allow the ARMPIT

PAD SUPPORTS(7) to be attached in three di󰀨erent positions. Start with the center position and

adjust if necessary.

Button Pin(9)

Bottom View

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to staminaproducts.com under the Customer Care section and order the part

needed, e-mail us at customer.care@staminaproducts.com, or call us toll free at 1-800-375-7520 (in the U.S.). Our Customer Care Sta󰀨 is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

Elastic Band

Page 8

ASSEMBLY INSTRUCTIONS

STEP 3

Insert the HEIGHT ADJUSTMENT BEAM(3) into the EXTENDING TUBE(2). Lock the HEIGHT ADJUSTMENT BEAM(3) in position by inserting the pin of the ADJUSTMENT KNOB(23) into one of the adjustment holes in the HEIGHT ADJUSTMENT BEAM(3) and tightening the ADJUSTMENT KNOB(23).

STEP 4

Insert the PAD TUBE(5) through the hole in the HEIGHT ADJUSTMENT BEAM(3) and secure with BUTTON HEAD BOLT(M8x1.25x22mm)(34). Slide the FOAM PADS(24) on both ends of the PAD TUBE(5).

STEP 5

Refer to detail view A, push in the BUTTON PIN(9) and insert the ADJUSTABLE INSTEP FRAME(4) into the HEIGHT ADJUSTMENT BEAM(3). Slide the FOAM PADS(24) on both ends of the ADJUSTABLE

INSTEP FRAME(4). NOTE: There are four adjustment holes in the HEIGHT ADJUSTMENT BEAM(3) which allow the

ADJUSTABLE INSTEP FRAME(4) to be attached in four di󰀨erent positions. Find the position which

is most comfortable for holding your ankles while performing the back stretching exercise.

Button Pin(9)

Page 9

1. To store the inLINE® Back Stretch Bench Pro, simply keep it in a clean dry place.

2. Adjust the HEIGHT ADJUSTMENT BEAM(3) and MAIN FRAME(1) to the shortest position. The

inLINE® Back Stretch Bench Pro is approximately 56 inches long x 18.5 inches wide x 14 inches tall. These dimensions will vary. Please measure your inLINE® Back Stretch Bench Pro if exact dimensions are needed.

3. To move the inLINE® Back Stretch Bench Pro, lift by the CUSHION(12) on one end and the

HEIGHT ADJUSTMENT BEAM(3) at the other end. Use caution as the SWING ARMS(6) may move and cause a pinching hazard.

The safety and integrity designed into the inLINE® Back Stretch Bench Pro can only be maintained when the inLINE® Back Stretch Bench Pro is regularly examined for damage and wear. Special attention should be given to the following:

1. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts. Tighten loose nuts and bolts.

2. Verify that the CAUTION LABEL(40) is in place and easy to read. Call Stamina Products immediately at 1-800-375-7520 for a replacement CAUTION LABEL(40) if it is missing or damaged.

3. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

4. Worn or damaged components must be replaced immediately or the inLINE® Back Stretch Bench Pro removed from service until repair is made.

5. Only Stamina Products supplied components should be used to maintain/repair the inLINE® Back

Stretch Bench Pro.

6. Keep your inLINE® Back Stretch Bench Pro clean by wiping it o󰀨 with an absorbent cloth after use.

STORAGE

MAINTENANCE

STRETCH SYSTEM

The inLINE® Back Stretch Bench Pro stretches the back with its one way rack and pinion engineering. Lie on the inLINE® Back Stretch Bench Pro with the ARMPIT PADS(8) under your armpits, and the FOAM PADS(24) holding your ankles. Pull the LEVER(13) back and forth as many times as needed until you feel a gentle stretch. Stop pulling at the desired position and stay at the stretched position for a few minutes. Push the LEVER(13)

rmly toward your feet to release the stretch.

Push the Lever toward your feet to release.

Pull the Lever back and forth as many times as needed to reach the proper stretch.

OPERATIONAL INSTRUCTIONS

Page 10

OPERATIONAL INSTRUCTIONS

1. Refer to illustration A. Push the LEVER(13) toward the FOAM PADS(24) at your feet and pull the EXTENDING TUBE(2) in to its shortest position.

2. Lie on the inLINE® Back Stretch Bench Pro with the ARMPIT PADS(8) under and supporting your armpits. If the ARMPIT PADS(8) do not rest comfortably under your armpits, adjust the ARMPIT PAD SUPPORTS(7) by pushing in the BUTTON PIN(9) and sliding them in or out of the SWING ARMS(6). Straighten your body and legs to determine if a height adjustment needs to be made.

3. To make a height adjustment, loosen and pull the ADJUSTMENT KNOB(23) and slide the HEIGHT ADJUSTMENT BEAM(3) to adjust. Lock the HEIGHT ADJUSTMENT BEAM(3) in desired position by inserting the pin of the ADJUSTMENT KNOB(23) into one of the adjustment holes in the HEIGHT

ADJUSTMENT BEAM(3). Tighten the ADJUSTMENT KNOB(23) to lock the HEIGHT ADJUSTMENT BEAM(3) securely.

4. Sit up on the CUSHION(12). Adjust the ADJUSTABLE INSTEP FRAME(4) by pushing in the BUTTON PIN(9) and sliding it up, then place your ankles between the FOAM PADS(24). Push the ADJUSTABLE INSTEP FRAME(4) down to secure your feet. Place the ADJUSTABLE INSTEP FRAME(4) at the

position which is most comfortable for holding your ankles. Lie down with the ARMPIT PADS(8) under and supporting your armpits, refer to illustration B.

5. To stretch, pull the LEVER(13) back and forth as many times as needed to reach the proper stretch. Stop pulling at the desired stretch position and stay at the stretch position for few minutes. To release, push the LEVER(13) rmly toward your feet.

USING THE inLINE® Back Stretch Bench Pro

To use the inLINE® Back Stretch Bench Pro, proper height adjustment is important. Use the following procedure to set the height adjustment for a revitalizing stretch.

ARMPIT PAD ADJUSTMENT

To accommodate di󰀨erent sizes of users, the ARMPIT PAD SUPPORTS(7) can be adjusted to one of three positions. Refer to the Bottom View illustration above. There are three adjustment holes in the bottom of the SWING ARM(6). Start with the center position and adjust if necessary. To adjust, push the BUTTON PIN(9) in and slide the ARMPIT PAD SUPPORTS(7) to the position that is comfortable. Make sure that the BUTTON PIN(9) is snapped into the proper adjustment hole before use.

Bottom View

Button Pin(9)

Page 11

LIMITED WARRANTY

MODEL 55-1406

WARRANTY

Stamina Products, Inc. (“Stamina”) warrants to the original purchaser that this product will be free from

defects in materials and workmanship that arise under normal use, service, proper assembly and proper operation in accordance with product warnings/instructions for a period of 90 days on the parts and one year on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY

SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY KIND OR TO ANY DEFECT OR CHANGE CAUSED BY IMPROPER ASSEMBLY, REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS NOT PROVIDED BY STAMINA. Commercial use includes use of product in athletic clubs, health clubs, spas,

gyms, and all other public or semipublic facilities whether or not the product’s use is in furtherance of a

prot making enterprise, and all other use which is not for personal purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. 2040 N Alliance

Ave, Springeld, Missouri, USA, MO 65803, or email us at customer.care@staminaproducts.com, or call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return

the product or part to us for free repair or replacement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE

THAN ONE (1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE

BEEN DISCOVERED. NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY (INCLUDING

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. These

warranties are not transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY. If any claim is made under this limited warranty or any

implied warranty, Stamina reserves the right to require the product to be returned for inspection, at the

purchaser’s expense, to Stamina’s premises in Springeld, Missouri. Return of the enclosed warranty

registration card is not required for warranty coverage, but is merely a way of establishing the date and place of purchase.

Stamina SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF TIME,

INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED WARRANTY.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY. NO ORAL OR WRITTEN INFORMATION GIVEN BY STAMINA, ITS AGENTS OR EMPLOYEES, SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. This warranty gives you specic legal rights, and you may also have other legal rights which vary from state to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

The laws in some states a󰀨ect the disclaimer or limitation of implied warranties and consequential and

incidental damages. If any such law is found applicable, the foregoing disclaimers and limitations of and

on implied warranties and consequential and incidental damages shall be deemed to be modied to the

extent necessary to comply with applicable law.

Page 12

PRODUCT PARTS DRAWING

FRONT

BACK

Page 13

PART# PART NAME QTY

PARTS LIST

1 Main Frame 1 2 Extending Tube 1 3 Height Adjustment Beam 1 4 Adjustable Instep Frame 1 5 Pad Tube 1 6 Swing Arm 2 7 Armpit Pad Support 2 8 Armpit Pad 2 9 Button Pin 3 10 Square Bushing 4 11 Bushing 4 12 Cushion 1 13 Lever 1 14 Ball end 1 15 Gear 1 16 Shaft 1 17 Twist Spring 1 18 Claw 1

19 C Ring (8mm) 1

20 Claw Stopper 1 21 Pressing Spring 1 22 Gear Rack 1 23 Adjustment Knob 1 24 Foam Pad 4 25 Wheel 2

26 Round Plug (19mm) 4 27 Round Plug (25mm) 4 28 Square Plug (30 x 30mm) 2 29 Endcap (38mm) 4 30 Shoulder Bolt, Button Head (M6 x 1 x 18mm) 1 31 Carriage Bolt (M8 x 1.25 x 35mm) 2 32 Carriage Bolt (M8 x 1.25 x 52mm) 2 33 Bolt, Button Head (M6 x 1 x 13mm) 4 34 Bolt, Button Head (M8 x 1.25 x 22mm) 1

35 Serial Decal 1

36 Bolt, Flat Head (M6 x 1 x 13mm) 2 37 Screw, Round Head (M3.4 x 8mm) 1 38 Nylock Nut (M8 x 1.25) 6

39 Pillow 1 40 Caution Label 1

41 Allen Wrench (4mm) 1 42 Allen Wrench (6mm) 1

43 Manual 1

Page 14

NOTES

Page 15

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: .................................................................................. Purchase Price: ............................................................................................

First Name: ............................................................................................ Last Name: ...................................................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

Email Address: ....................................................................................... Phone #: ( ) ......................................................................................

Would you like to receive email information or special o󰀨ers from Stamina Products?* ____Yes ____No

*If yes, be sure your email address is included above.

Stamina Products, Inc.

2040 N Alliance Ave, Springeld, MO 65803

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions, please contact customer care. Do not return the product. To order parts by mail, fill out the sheet below and fax it to

417-889-8064. The part will be mailed to your address.

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

IMPORTANT : We require your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT: Before lling out the portion below, make sure you have the correct information.

Refer to the parts list to make sure you're ordering the right parts!

Stamina Products, Inc.

2040 N Alliance Ave, Springeld, MO 65803

Detach and Mail or Fax the Form Above

TO CONTACT CUSTOMER CARE

For your convenience, Stamina’s customer care representatives can be reached by email at customer.care@staminaproducts. com or by phone at 1-800-375-7520 (in the U.S.). Our customer care representatives are available Monday through Thursday

from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

TO REGISTER YOUR PRODUCT

Would you like to recieve email information or special o󰀨ers from Stamina Products? Register at contact.staminaproducts.com

TELEPHONE

CUSTOMER CARE

Tel: 1 (800) 375-7520

FAX

CUSTOMER CARE

Fax: (417) 889-8064

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Care

2040 N Alliance Ave, Springeld, MO 65803

ONLINE

CUSTOMER CARE

customer.care@staminaproducts.com

www.staminaproducts.com

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model

number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your product) ready.

If you don’t have internet access, you can call customer care at 1-800-375-7520, or ll out and mail the product registration form below to Stamina Products, Inc.; 2040 N Alliance Ave, Springeld, MO 65803.

PRODUCT REGISTRATION FORM

TO ORDER PARTS

Detach and Mail or Fax the Form Below

PARTS ORDER FORM

PART # DESCRIPTION QUANTITY

1 Rear Unit Assembly 1

EXAMPLE: