Stamina Gravity Inversion Table, 55-1538 Owner's Manual

55-1538

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

CAUTION: 1. Weight on this product should not exceed 300 lbs.

2. Class H equipment: This equipment is for home
use only. It is not for commercial use.

! WARNING !

Exercise can present a he alth
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

When calling for parts or
service, please specify the
following number.

2005, 12

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

www.staminaproducts.com

This Product is Produced Exclusively by

2005 Stamina Products, Inc.

Owner's Manual

2

SAFETY INSTRUCTIONS

2

WARNING:

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

Read all warnings posted on the Gravity Inversion Table.
The Gravity Inversion Table should only be used after a thorough review of the Owner's Manual.
We recommend that two people be available for assembly of this product.
Do not use the Gravity Inversion Table alone. Always have a helper availa ble in case assistance is needed
in recovering from the decline position.
Verify that adequate head clearance is available between the user's head and the floor before using this
inversion table. This is especially important for tall users.
Make sure that the Pivot Arms are assembled using the same hole on both Pivot Arms. Pay close attention to
Steps 3 and 4 on page 7.
Make sure that the Pivot Arms are always se cured to the pegs on the Main Fra me with the Bolts a nd W ashers.
Adjust the Nylon Straps to an angle of 15 to 20 degrees a nd use this setting until you have verified your height
setting and become familiar with the Gravity Inversion Table.
Use the lowest holes in the Pivot Arms until you become familiar with the Gravity Inversion Table.
You must understand how to recover from the fully inverted position before using the fully inverted position.
Read the RECOVER Y FROM LOCKED POSITION se ction at the bottom of page 12 BEFORE using the fully
inverted position.
Do not allow children to use or play on the Gravity Inversion Table.
Keep small children and pets away from the Gravity Inversion Table at all times.
The Gravity Inversion Table should not be used by persons weighing more than 300 lbs.
The Gravity Inversion Table should not be used by persons over 6 feet 6 inches tall.
It is recommended that you place this exercise equipment on an equipment mat.
Use the Gravity Inversion T able only on a level surface.
W ear a ppropriate clothing when exercising; do not wear loose clothing that could become caught in the Gravity

Inversion T a ble.

Be sure that there is enough room for the bed to rotate completely.
Use the Gravity Inversion Table only as described in the manual.
The safety level of the Gravity Inversion T a ble ca n be maintained only if it is examined regularly for damage
and wear.
This equipment is for home use only. It is not for commercial use.

Maintenance Instructions 13
Product Parts Drawing 14
Parts List 15
Warranty 16
Notes 17
Fax/Mail Ordering Form 18

Safety Instructions 2
Before Y ou Begin 4
Hardware Identification Chart 5
Assembly Instructions 6
Operational Instructions 10
Storage 13

TABLE OF CONTENTS

Page Page

Extreme obesity
Glaucoma, retinal detachment or conjunctivitis
Pregnancy
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Middle ear infection
High blood pressure, Hypertension, Recent stroke or Transient ischemic attack
Heart or circulatory disorders for which you are being treated
Hiatus hernia or Ventral hernia
Bone weaknesses including Osteoporosis, Unhealed fractures, Medullary pins, or
Surgically implanted orthopedic supports.
Use of anti-coagulants including Aspirin in high doses.

WARNING: Before using this equipment you should consult with your personal physician to see if inversion

equipment is appropriate for you. Do not use this equipment without your physici an's approval. Do not use
this equipment if you have any of the following conditions or ailments:

To reduce the risk of serious injury, read the following safety instructions before
using the

Gravity Inversion T able.

THANK YOU FOR PURCHASING THE

Gravity Inversion Table

To help you get started, we have pre-assembled most of your

Gravity Inversion Table at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

Within a few minutes you will be getting your body into shape and on your

way to achieving a happier and healthier lifestyle.

Should you have any que stions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Friday, 8:00 A.M. - 5:00 P.M., Central Time.

CALL US FIRST

3

Thank you for choosing the Gravity Inversion

Table. W e ta ke great pride in producing this quality

product and hope it will provide ma ny hours of quality
exercise to make you feel better , look better and enjoy
life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The

Gravity Inversion

Table provides a convenient and simple method to

begin your a ssault on getting your body in sha pe and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this ma nual carefully bef ore
using the

Gravity Inversion T able.

BEFORE YOU BEGIN

4

Pivot Arm

Bumper

Footrest

Heel Holder

Height

Adjustment Beam

Front Frame

Main Fra me

Buckle Strap

Hand Grip

Rear Frame

Although Stamina tries to manufa cture its products
with the finest materials and uses the highest
standards of ma nufacturing, occasionally a part that
does not fit, is the incorrect size, or is otherwise
inappropriate is found. Even with the highest
inspection and quality controls in place these things
will happen occasionally. Please do not return the
product. For your convenience, Stamina has a
Customer Service Department with a toll-free
number. If a part is missing, does not fit, is the
incorrect size, or is otherwise inappropriate, please
call 1 [phone] (in the U.S.) between 8:00 A.M.
and 5:00 P.M. Central T ime, Monday through Friday .
Our operators will be able to assist you with your
problem and the parts will be mailed directly to your
house.

Adjustment Knob

Endcap

Stand

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : W rench

Combination Wrench

Protective Cover

Nylon Bed

Protective Cover

5

Part No. and Description Qty

HARDWARE IDENTIFICATION CHAT

Place washers, the end of bolts or screws on the circles to check for the
correct size. Use the small scale to check the sizes of bolts and screws.

This chart is provided to help identify the hardware used in the assembly process.

After unpacking the unit, open the hardware bag and make sure that you have the following items:

length

length

mm.

in.

INCHES

MILLIMETERS

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

6 8 10 12

3/16" 5/16" 1/2"3/8"1/4"

NOTICE: The length of all kinds of screws and bolts are not included

themselves head, except the flat head screws and bolts.

42 Nylock Nut (M6 x 1) 2

38 Bolt, Round Head (M6 x 1 x 10mm) 2

40 Bolt, Hex Head (M6 x 1 x 47mm) 2

44 Larger Washer (M6) 2
45 Washer (M6) 4

1. Some of the hardware items listed may be attached to other parts.

2. Bolt length is measured from the bottom of the bolt head to the end of the bolt.

NOTE:

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at:

[e-mail]

6

STEP 1

Unf old the BASE ASSEMBL Y to an upright position by moving the FRONT FRAME(1) away from REAR

FRAME(2). Then push down on the middle of the two FOLDING LINKAGES(3) until they are fully

locked down.

STEP 2

Slide one PROTECTIVE COVER(23) onto each side of the BASE ASSEMBLY, and pull the covers
down until the bottom of the covers are slightly lower than the

FOLDING LINKAGES(3). Secure the

PROTECTIVE COVERS(23) to the FOLDING LINKAGES(3) with the SECURING STRAPS on the

bottom of the covers.

NOTE:

When the PROTECTIVE COVERS(23) are asse mbled correctly , the FOLDING LINKAGES(3)
should not be visible. Refer to the illustration.

ASSEMBLY INSTRUCTIONS

7

STEP 3

Slide the bottom of the two PIVOT ARMS(5) into the brackets located at ea ch side of the MAIN FRAME(4).
Align the desired hole on the arm with the peg on the bracket, and insert the peg into the hole to lock the

PIVOT ARMS(5) in position. Then secure the PIVOT ARMS(5) on the pegs with ROUND HEAD
BOLTS(M6 x 10mm)(38) and LAR GE WASHERS(M6)(44).

PIVOT ARM ADJUSTMENT:

There are three adjustment holes on the PIVOT ARMS(5) allowing you to position the MAIN FRAME(4)
at three different heights. The lowest hole will allow the least amount of inversion angle. The top hole will
allow the greatest amount of inversion angle.

CAUTION:

STEP 4

Attach the MAIN FRAME(4) onto the REAR FRAME(2) by sliding the slots in the ends of the two PIVOT

ARMS(5) into the slots on the REAR FRAME(2).

Use the lowest holes in the

PIVOT ARMS(5) until you become familiar with the Gravity

Inversion T able.

Both PIVOT ARMS(5) must be adjusted to the same hole. Trying to adjust the PIVOT

ARMS(5) to different positions could cause da mage to the machine, and injury to the user.

1.

2.

SLOTS

ASSEMBLY INSTRUCTIONS

8

STEP 5

Attach the FOOTREST(8) onto the HEIGHT ADJUSTMENT BEAM(6) with the ADJUSTMENT

KNOB(9).
NOTE:

STEP 6: Insert the PAD TUBE(10) through the hole on the HEIGHT ADJUSTMENT BEAM(6) and

secure with

HEX BOL T(M6 x 47mm)(40), NYLOCK NUT(M6)(42), and WASHERS(M6)(45). Place

a

HEEL HOLDER BRACKET(11) onto a HEEL HOLDER(12), then slide them onto PAD TUBE(10)

together. Slide a nother set of HEEL HOLDER BRACKET(1 1) a nd HEEL HOLDER(12) over the other
end of the

PAD TUBE(10).

STEP 7: Attach the ADJUSTABLE INSTEP FRAME(7) to the HEIGHT ADJUSTMENT BEAM(6)

by pulling the SMALL SPRING PIN(15) a nd sliding the ADJUST ABLE INSTEP FRAME(7) completely
into the

HEIGHT ADJUSTMENT BEAM(6). Place a WASHER(M6)(45) onto the HEX BOLT
(M6 x 47mm)(40), then insert the bolt the halfway through the square tube on the HEIGHT ADJUSTMENT
BEAM(6), slide the bolt through the ring at the bottom of the SPRING(13), slide the bolt through the

square tube and secure with

NYLOCK NUT(M6)(42) and WASHER(M6)(45). Press the SQUARE

PLUG(35) into the HEIGHT ADJUSTMENT BEAM(6). Install a HEEL HOLDER BRACKET(11)

and HEEL HOLDER(12) onto both sides of the ADJUST ABLE INSTEP FRAME(7).

The four adjustment holes in the FOOTREST(8) allow the FOOTREST(8) to be atta ched in f our
different positions. Start with one of the center positions and adjust if necessary. Use the outer
position if users are taller than average. Use the inner position if users are shorter than average.

ASSEMBLY INSTRUCTIONS

9

1.

2.

STEP 8

Install the HEIGHT ADJUSTMENT BEAM(6) into MAIN FRAME(4) by pulling the LARGE SPRING

PIN(18) on the MAIN FRAME(4) and inserting the HEIGHT ADJUSTMENT BEAM(6) a s shown. For

added safety, thread the

LOCKING KNOB(19) into back side of the MAIN FRAME(4).

WARNING:

STEP 9

Attach the NYLON STRAP(27) onto the BUCKLE on the end of the BUCKLE STRAP(28) by inserting
the end of the stra p up through the bottom of the buckle, as shown in the illustration 1.

STEP 10

Hook the end of the NYLON STRAP(27) onto the loop on the back of the MAIN FRAME(4). Hook the
end of the

BUCKLE STRAP(28) onto the loop on the FRONT FRAME(1).

NOTE:

A.

C.

B.

BUCKLE

Do not use the Gravity Inversion T able until you have verified your height setting. Failure
to use the proper height setting can result in difficulty recovering from the decline position.
See

HEIGHT ADJUSTMENT instructions on page 10.

The

NYLON STRAPS are used to control the decline angle of the Gravity Inversion Table.

For a steeper decline angle, lengthen the straps. For a lessor decline angle, shorten the straps.
Make sure these

NYLON STRAPS are tight in the buckle and check the decline angle before

using the

Gravity Inversion T able.

OPERATIONAL INSTRUCTIONS

10

GENERAL PRECAUTIONS

Use the lowest holes in the PIVOT ARMS(5) until you become fa miliar with the Gravity Inversion T a ble.
Do not use the Gravity Inversion Table alone. Always have a helper available in case assistance is
needed in recovering from the decline position.
Make sure that the HEEL HOLDERS(12) are holding your feet securely.
Make sure that the HEIGHT ADJUSTMENT BEAM(6) is properly set for your height.
Make sure that the HEIGHT ADJUSTMENT BEAM(6) is held securely by both the LARGE SPRING
PIN(18) and the LOCKING KNOB(19).
Make sure that there is enough room for the bed to rotate completely .

1.

2.

3.

4.

5.

6.

THE HANDLEBARS

For added convenience, and safety, a set of HANDLEBARS has been added to the Gravity Inversion

Table. These HANDLEBARS are located at the top of the REAR FRAME(2). The HANDLEBARS are to

help you return to the upright position from any degree of inversion. If you wish to return to the upright
position, and the bed is moving too slowly, or not moving at all, simply grab the HANDLEBARS and pull on
them until you return to the upright position.

HEIGHT ADJUSTMENT

The Gravity Inversion Table is a very sensitive balance device. It responds to very slight changes in
weight distribution. It is very important to make sure that the height adjustment is adjusted properly. Use
the following procedure to set the height adjustment and balance the

Gravity Inversion Table.

Adjust the NYLON STRAPS to restrict
movement to approximately 15 degrees
beyond the horizontal position. The
nylon straps

should not allow the Gravity

Inversion T able to go into the full inversion

position while you are setting the height
adjustment.
Loosen the

LOCKING KNOB(19) under

the

MAIN FRAME(4).

Pull the LARGE SPRING PIN(18) a nd use
the

SCALE DECAL(16) to set the

HEIGHT ADJUSTMENT BEAM(6).

Tighten the LOCKING KNOB(19).
Mount the machine.
Lock your ankles into the

HEEL

HOLDERS(12).

Lie back with your hands at your sides.
Slowly raise your hands to your chest.
If your feet are higher than your head,
dismount and try a taller setting. If you do
not rotate to a position close to level,
dismount and try a shorter setting.

3.

4.

5.

1.

2.

6.

7.

8.

9.

The

Gravity Inversion T a ble should return to the upright position when your ha nds are below

your waist. If it does not, use a taller setting.
Verify that adequate head clearance is available between the user's head and the floor before
using this inversion table. This is especially important for tall users.

NOTE:

1.

2.

Handlebars

OPERATIONAL INSTRUCTIONS

11

Start by lying fully back on the bed with your hands at your side, or resting on your thighs.
Keeping your hands close to your body begin to raise your arms slowly allowing the table to rotate
backward. Stop, or lower your arms to control the downward rotation of the table.
Raise your arms until they are over your head. At this point, the inversion table will be as far back as it
can go.
As you get more comfortable with the use, rock the bed slowly by moving your arms up a nd down slowly .
A gentle swinging motion will altern ately put your spine in tra ction a nd compression. This rhythmic type
of traction is used by many hospitals and doctors to treat certain back problems.
It is recommended that the inversion table be used for f ive or ten minutes ea ch morning, a nd again ea ch
evening.
Return to the upright position by slowly moving your hands back down to your thighs.

USING THE INVERSION TABLE

1.

2.

3.

4.

5.

6.

7.

3.1.

4.2.

OPERATIONAL INSTRUCTIONS

12

Begin slowly: Invert only 15-20 degrees to begin with. Stay inverted only a s long a s you are comfortable.
Return upright slowly .
Make gradual changes: Increase the angle only if it is comfortable. Increase the angle only a few
degrees at a time. Increase the time of use 1-2 minutes up to ten over a period of weeks. Add stretching
and light exercise only after you are comfortable with inversion.
Watch your body: Come up slowly, dizziness after a session means you came up to fast. Wait a while
after eating before using table. If you get nauseous, do not f ight it, come up a s soon as you feel queasy.
Keep moving: Movement while inverted encourages blood, lymph, a nd spin al fluid circulation and aids
in alignment of bones and organs. Movement may be accomplished by either rhythmic traction or light
exercise. Do not exercise strenuously while inverted. Limit partial inversion without movement to one or
two minutes. Limit full inversion with no movement to only a few seconds.
Invert regularly: W e recommend two or three time s a day depending upon your current condition. T ry to
schedule it for the same times each day.

SUGGESTIONS FOR USE

1.

2.

3.

4.

5.

A. B. C.

LOCKING THE BED

When the inversion table rotates past the vertical inverted position the bed becomes locked, and will not
return to the upright position in the usual way . The locked position allows you to ha ng straight upside-down
completely free of the bed. This position allows you to enjoy all of the benefits of a ha ndsta nd, with none of
the discomforts, as shown in illustration A. It also allows you to do exercises such as the waistband, as
shown in illustration B.
T o get into the locked position, use the top hole in the

PIVOT ARMS(5) as described in a ssembly STEP 3.

If necessary, adjust the HEIGHT ADJUSTMENT BEAM(6) shorter, and then mount and use normally.
When your arms are completely extended above your head, the bed will rotate all the way to the locked
position.

CAUTION: You must understand how to recover from the fully inverted position before using the fully

inverted position. Read the

RECOVERY FROM LOCKED POSITION section below

BEFORE using the fully inverted position.

RECOVERY FROM LOCKED POSITION

To recover from the locked position, simply grab the HANDLEBARS and pull on them while pushing back
on the

HEEL HOLDERS(12) with your legs. If you can not re ach the HANDLEBARS, then you can still

recover by grabbing the back of the bed with one hand, the

REAR FRAME(2) with the other, and pulling

your hands together, as shown in illustration C.

13

STORAGE

FOLDING THE INVERSION TABLE

The Gravity Inversion Table ca n be easily folded for storage.

To fold the

Gravity Inversion Table loosen LOCKING KNOB(19) and pull out the LARGE SPRING

PIN(18). Now, slide the HEIGHT ADJUSTMENT BEAM(6) all the way up into the MAIN FRAME(4)

until the ADJUSTABLE INSTEP FRAME(7) is just below the MAIN FRAME(4), release the LARGE

SPRING PIN(18) and slide the HEIGHT ADJUSTMENT BEAM(6) slightly up or down until the spring

pin locks the bea m in pla ce. Re move the

MAIN FRAME ASSEMBLY from the BASE by lifting up on the
MAIN FRAME(4) until the PIVOT ARMS(5) come out of the slots located at the top of the REAR
FRAME(2), (Make sure the NYLON STRAP is not attached to the MAIN FRAME(4) before attempting

to remove it.) Push up on the center of the

FOLDING LINKAGES(3) a nd push the FRONT FRAME(1)

and REAR FRAME(2) together until they meet.

MAINTENANCE INSTRUCTIONS

The safety level of the Gravity Inversion Table can be maintained only if it is examined regularly for
damage and wear.

Check the warning label, nylon strap, strap buckle, pivot arms, nylon bed, heel holders, small spring pin
and large spring pin for damage and wear.
Replace damaged and worn components immedi ately and/or kee p the equipment out of use until re pairs
are completed.

1.

2.

PRODUCT PARTS DRAWING

BACK

FRONT

14

PARTS LIST

DIAGRAM# PART NAME QTY

15

1 Front Frame 1
2 Rear Frame 1
3 Folding Linkage 2
4 Main Frame 1
5 Pivot Arm 2
6 Height Adjustment Beam 1
7 Adjustable Instep Frame 1
8 Footrest 1
9 Adjustment Knob 1
10 Pad Tube 1
11 Heel Holder Bracket 4
12 Heel Holder 4
13 Spring 1
14 Roll Pin 1
15 Small Spring Pin 1
16 Scale Decal 1
17 Bushing 2
18 Large Spring Pin 1
19 Locking Knob 1
20 Foam Pad 1
21 Double sided Tape 1
22 Nylon Bed 1
23 Protective Cover 2
24 Hand Grip 2
25 Bumper 1
26 Hook 2
27 Nylon Strap 1
28 Buckle Strap 1
29 Hollow Cap 1
30 Stand 2
31 Endcap 2
32 Dome Plug (22.2mm) 4
33 Round Plug (31.8mm) 2
34 Square Plug (33.4mm x 33.4mm) 1
35 Square Plug (38mm x 38mm) 2
36 Oval Plug (20mm x 60mm) 2
37 Support Washer 1
38 Bolt, Round Head (M6 x 1 x 10mm) 2
39 Bolt, Round Head (M6 x 1 x 45mm) 4
40 Bolt, Hex Head (M6 x 1 x 47mm) 2
41 Bolt, Hex Head (M8 x 1.25 x 25mm) 2
42 Nylock Nut (M6 x 1) 6
43 Nylock Nut (M8 x 1.25) 2
44 Large Washer (M6) 2
45 Washer (M6) 16
46 Washer (M8) 4
47 Warning Label 1
48 Wrench 1
49 Combination Wrench 1
50 Manual 1

LIMITED WARRANTY

MODEL 55-1538

16

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and 3 years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, fa mily, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Stamin a Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 [phone]. If the defect is covered under this limited
warranty , you will be requested to return the product or part to us f or free repair or repla cement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE T O YOU. In the event that the purchaser makes any claim under this

limited warranty or a ny implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date and place of purchase.

Stamin a Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or express warranty given by Stamina Products, Inc. This warra nty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers and li mitations of a nd on implied warranties a nd
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

WARRANTY

NOTES

17

IMPORT ANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORT ANT : We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Plea se do not return the product. For your convenience, Sta mina has a Customer Service Department with
a toll-free number. Should a part be missing or a defective part found, please call 1 [phone]
(in the U.S.) between 8:00 A.M. and 5:00 P .M. Central T i me, Monday through Friday or f ill out the fax sheet
ordering form below and fax it to [phone]. Our Customer Service Department will be able to assist
you with your problem and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1

EXAMPLE: