Stamina CPS 9190 Indoor Cycle, 15-9190 Owner's Manual

When calling for parts or

service, please specify

the following number

:

Model#: 15-9190

CAUTION:
Weight on this product should not exceed 300 lbs.

Owner's

Manual

This Product is Produced Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

Product May Vary Slightly From Pictured.

!

WARNING

!

Exercise can present a
h e a l t h r i sk . Co n su l t a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
dis c o n t i n ue use of this
equipment. Serious bodily
in j u r y c a n occ u r if th is
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all in str uct ion s a re not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

STAMINA PRODUCTS

MADE IN CHINA

©

2009 Stamina Products, Inc.

2009, 09

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning & Notice Labels ........ 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Set Up Instructions ..................................... 9

Operational Instructions ........................... 10

Storage ....................................................... 12

Maintenance ............................................... 12

Conditioning Guidelines ........................... 13

Warm-Up and Cool-Down ......................... 14

Warranty ..................................................... 15

Product Parts Drawing .............................. 16

Parts List .................................................... 17

Fax/Mail Ordering Form ............................ 19

SAFETY INSTRUCTIONS

2

1. Read all warnings posted on the CPS 9190 Indoor Cycle.

2. The CPS 9190 Indoor Cycle should only be used after a thorough review of the Owner’s Manual.

3. We recommend that two people be available for assembly of this product.

4. Keep children away from the CPS 9190 Indoor Cycle. Do not allow children to use or play on the CPS
9190 Indoor Cycle. Keep children and pets away from the CPS 9190 Indoor Cycle when it is in use.

5. The CPS 9190 Indoor Cycle is not a freewheeling exercise bike; therefore, pedal speed should be reduced
in a controlled manner to prevent injury from spinning pedals.

6. Make sure the CPS 9190 Indoor Cycle is properly assembled and that all nuts and bolts are tightened
before use.

7. It is recommended that you place this exercise equipment on an equipment mat.

8. Set up and operate the CPS 9190 Indoor Cycle on a solid level surface. Do not position the CPS 9190
Indoor Cycle on loose rugs or uneven surfaces.

9. Make sure that adequate space is available for access to and around the CPS 9190 Indoor Cycle.

10. Adjust the STANDS(51) under the FRONT and REAR STABILIZERS(3, 4) so that the CPS 9190 Indoor

Cycle sits on the oor without rocking. See page 9 for detailed leveling instructions.

11. Before using, inspect CPS 9190 Indoor Cycle for worn or loose components, and tighten or replace any
worn or loose components prior to use.

12. Before getting on the CPS 9190 Indoor Cycle, always check the SEAT POST(5), SEAT SLIDER(6),
PEDALS(16, 17), and HANDLEBAR(2) to be sure they are secure. The ADJUSTMENT KNOBS(48) must
be inserted into one of the holes in the SEAT POST(5) and the HANDLEBAR(2) and tightened.

13. Each user should adjust the seat per instructions on page 10.

14. Do not attempt to adjust the seat while you are on the CPS 9190 Indoor Cycle.

15. Consult a physician prior to commencing an exercise program and follow his/her recommendations in

developing your tness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop

and consult your physician.

16. Follow your physician’s recommendations in developing your own personal tness program.

17. Always choose the workout which best ts your physical strength and exibility level. Know your limits and
train within them. Always use common sense when exercising.

18. Do not wear loose or dangling clothing while using the CPS 9190 Indoor Cycle.

19. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross

training shoes that t well, provide foot support, and feature non-skid rubber soles.

20. Care should be taken in mounting or dismounting the CPS 9190 Indoor Cycle.

21. The CPS 9190 Indoor Cycle should not be used by persons weighing over 300 pounds.

22. The CPS 9190 Indoor Cycle should be used by only one person at a time.

23. The CPS 9190 Indoor Cycle is for consumer use only. It is not for use in public or semipublic facilities.

!

WARNING: To reduce the risk of serious injury, read the following Safety Instructions

before using the CPS 9190 Indoor Cycle.

WARNING: Before starting any exercise or conditioning program you should consult with your personal physician
to see if you require a complete physical exam. This is especially important if you are over the age of 35, have never
exercised before, are pregnant, or suffer from any illness.

READ AND FOLLOW THE SAFETY PRECAUTIONS.

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.

!

THANK YOU FOR PURCHASING THE

CPS 9190 Indoor Cycle

To help you get started, we have pre-assembled most of your

CPS 9190 Indoor Cycle at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

3

Call Us First

www.staminaproducts.com

1 [phone]

Customer Service

Thank you for choosing the CPS 9190 Indoor

Cycle. We take gr eat prid e in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better, look
better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The CPS 9190 Indoor
Cycle provides a convenient and simple method to
begin your assault on getting your body in shape
and achieving a happier and healthier lifestyle.

Befor e r e ading fu r t h er, p lease rev i e w the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the CPS

9190 Indoor Cycle.

BEFORE YOU BEGIN

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your CPS 9190 Indoor
Cycle, please do not return the product. Contact
us FIRST!

If a par t is missing o r defective, please call

us toll free at 1-800-375-7520 (in the U.S.). Our

Customer Service Staff is available to assist you
from 7:30 A.M. to 5:00 P.M. (Central Time) Monday
th rou gh Thursday and 8: 00 A.M. to 3:00 P.M.
(Central Time) on Friday.

If you would like to contact us online, go to our
website at www.staminaproducts.com and access
the Customer Service section.

Be sure to have the name and model number of
the product available when you contact us.

4

Seat

Rear Stabilizer

Wheel

Handlebar

Right Crank

Flywheel

Seat Slider

Seat Post

Chain Guard

Adjustment Knob

Right Pedal

Water
Bottle

Holder

Front Stabilizer

Main Frame

Tension Knob

Warning Label

Stand

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Wrench

Allen Wrench (5mm)

Adjustment Knob

Label is larger than actual size

This chart is provided to help identify the warning & notice labels on the CPS 9190 Indoor Cycle.
Please take a moment to familiarize yourself with all of the warning & notice labels.

EQUIPMENT WARNING & NOTICE LABELS

WARNING LABEL(70)W1

5

Part Number and Description Qty

This chart is provided to help identify the hardware used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

HARDWARE IDENTIFICATION CHART

6

mm.

in.

INCHES

MILLIMETERS

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

6 8 10 12

3/16" 1/4" 5/16" 3/8" 1/2"

69 Washer (M8) 4

55 Bolt, Button Head (M8 x 1.25 x 15mm) 4

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the
packing materials until assembly is completed. Read each step carefully before beginning. If you

are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at

[e-mail].

ASSEMBLY INSTRUCTIONS

7

STEP 1

Make the WHEELS(49) on the FRONT STABILIZER(3) face the front, then attach the FRONT STABILIZER(3)
to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M8x1.25x15mm)(55) and WASHERS(M8)(69).

STEP 2

Attach the REAR STABILIZER(4) to the MAIN FRAME(1) with BUTTON HEAD BOLTS(M8x1.25x15mm)
(55) and WASHERS(M8)(69).

NOTE: See page 10 for detailed leveling instructions to prevent rocking.

STEP 3

Pull the ADJUSTMENT KNOB(48), then insert the SEAT POST(5) into the MAIN FRAME(1) and secure
with the ADJUSTMENT KNOB(48).
NOTE: The pin of the ADJUSTMENT KNOB(48) should be inserted into one of the adjustment holes in

the SEAT POST(5). And the ADJUSTMENT KNOB(48) should be screwed in tight to make the

SEAT POST(5) ts securely in the MAIN FRAME(1).

ASSEMBLY INSTRUCTIONS

8

STEP 4

NOTE: The RIGHT PEDAL(17) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(17) has

right hand threads and is tightened by turning clockwise. The LEFT PEDAL(16) has L stamped on
the end of the pedal shaft. The LEFT PEDAL(16) has left hand threads and is tightened by turning

counterclockwise.
Thread the RIGHT PEDAL(17) into the RIGHT CRANK(13) as shown. Tighten the pedal securely. Do the
same to attach the LEFT PEDAL(16) to the LEFT CRANK(12).

STEP 5

Pull the ADJUSTMENT KNOB(48), then insert the HANDLEBAR(2) into the MAIN FRAME(1) and secure
with the ADJUSTMENT KNOB(48).
NOTE: The pin of the ADJUSTMENT KNOB(48) should be inserted into one of the adjustment holes in

the HANDLEBAR(2). And the ADJUSTMENT KNOB(48) should be screwed in tight to make the

HANDLEBAR(2) ts securely in the MAIN FRAME(1).

Place the CPS 9190 Indoor Cycle in the area where it will be used. It is recommended that the CPS 9190
Indoor Cycle be placed on an equipment mat. The CPS 9190 Indoor Cycle is approximately 50 inches

long (max.) x 18 3/8 inches wide x 42 5/8 inches tall (max.). An area 4 feet wide x 6 feet long is required
for safe operation of the CPS 9190 Indoor Cycle. Make sure that adequate space is available for access
to and passage around the CPS 9190 Indoor Cycle.

LEVELING: Adjust the STANDS(51) under the FRONT and REAR STABILIZER(3, 4) so that the CPS

9190 Indoor Cycle sits on the floor without rocking. Refer to the instructions below the

illustration.

MOVING: The CPS 9190 Indoor Cycle has a pair of WHEELS(49) on the FRONT STABILIZER(3).

Lift up the REAR STABILIZER(4) to move the CPS 9190 Indoor Cycle.

CAUTION: Locate and read the WARNING LABEL(70) on the CPS 9190 Indoor Cycle. Make sure that

all users read the WARNING LABEL(70).

SET UP INSTRUCTIONS

9

FUNCTION INSPECTION:

Visually inspect the CPS 9190 Indoor Cycle to verify that assembly is as shown in the above illustration.
Check the function of the CPS 9190 Indoor Cycle by turning the crank slowly through one complete
revolution to verify that the drive train functions properly. Adjust the TENSION KNOB(34) to verify that the
adjustable tension is working properly.

Loosen the NUTS(M8x1.25)(67) until they
touch the STANDS(51). Adjust the STANDS(51)
for leveling. Tighten the NUTS(M8x1.25)(67)
securely against the STABILIZERS(3, 4) to lock
the STANDS(51) in position.

Equipment Mat

OPERATIONAL INSTRUCTIONS

10

SEAT HEIGHT ADJUSTMENT

Proper seat height is important for efcient exercise. To determine proper seat height, place your foot in the
toe cage of the pedal closest to the oor and mount the bike. Sit on the BIKE and move one of the pedals

to the down position. Your leg should be slightly bent and relaxed as shown.

LOAD ADJUSTMENT

To increase the load, turn the TENSION KNOB(34) clockwise.
To decrease the load, turn the TENSION KNOB(34)
counterclockwise.

CAUTION!

The TENSION KNOB(34) is the Emergency Brake, too. The
CPS 9190 Indoor Cycle can be stopped immediately by
pushing down the TENSION KNOB(34).

FORWARD/AFT POSITION OF SEAT

Adjusting the SEAT(43) forward or backward helps you work
on different lower body muscle groups.

Loosen the LOCKING KNOB(46), slide the SEAT(43) to the
desired position, and secure with the LOCKING KNOB(46).
NOTE: The LOCKING KNOB(46) should be screwed in tight

to make the SEAT SLIDER(6) t securely in the SEAT

POST(5).

If your leg is too straight or if your foot cannot touch the pedal when extended at the downstroke, you will
need to lower the seat. If your leg is bent too much, you will need to raise the seat. Loosen and pull the

ADJUSTMENT KNOB(48), then lower or raise the SEAT(43) to the desired height, and secure with the
ADJUSTMENT KNOB(48). Make all adjustments to seat height while off of the bike.

NOTE: The ADJUSTMENT KNOB(48) should be screwed in tight to make the SEAT POST(5) ts securely

in the MAIN FRAME(1).

OPERATIONAL INSTRUCTIONS

11

PEDAL STRAP ADJUSTMENT

Use the following procedure to adjust the PEDAL STRAP:

HANDLEBAR HEIGHT ADJUSTMENT

HANDLEBAR(2) height is a matter of preference. Start with
the HANDLEBAR(2) at the same height as the seat. Adjusting
the HANDLEBAR(2) higher will give the rider a more upright
position; lowering the HANDLEBAR(2) will result in a more
prone position.

To adjust, loosen and pull the ADJUSTMENT KNOB(48), then

lower or raise the HANDLEBAR(2) to the desired height, and
secure with the ADJUSTMENT KNOB(48).

NOTE: The ADJUSTMENT KNOB(48) should be screwed

in tight to make the HANDLEBAR(2) t securely in the MAIN

FRAME(1).

1.Place the ball of each foot on the pedal and in the toe cage such that the ball of the foot is centered over
the pedal spindle and under the strap.

2.Rotate the cranks until one foot is in a position closest to you.

3.To tighten the strap, pull up on the end of the strap until it ts snugly over your shoe. Make sure that the

strap is secure, but not overly tight or pressing uncomfortably on your foot.

4.Repeat for the other foot.

5.To loosen the pedal strap, press down on the clip that holds the strap secure, and pull slightly outward.
Release the clip to lock the strap into place.

Right Pedal(17)

Toe Cage

Pull the Pedal Strap to tighten.

Press the clip down and pull slightly
outward to loosen the Pedal Strap.

1. To store the CPS 9190 Indoor Cycle, simply keep it in a clean dry place.

2. Adjust the HANDLEBAR(2) and the SEAT POST(5) to the lowest position. Adjust the SEAT SLIDER(6)

to the most forward position. The CPS 9190 Indoor Cycle is approximately 40 3/4 inches long (min.)
x 18 3/8 inches wide x 37 1/4 inches tall (min.). These dimensions will vary. Please measure your CPS
9190 Indoor Cycle if exact dimensions are needed.

3. To move the CPS 9190 Indoor Cycle, lift the REAR STABILIZER(4) and use the WHEELS(49) on the

FRONT STABILIZER(3).

The safety and integrity designed into the CPS 9190 Indoor Cycle can only be maintained when the
CPS 9190 Indoor Cycle is regularly examined for damage and wear. Special attention should be given

to the following:

STORAGE

MAINTENANCE

12

OPERATIONAL INSTRUCTIONS

ADDING A FITNESS MONITOR OR METER

The CPS 9190 Indoor Cycle does not include a tness
monitor or meter, but is equipped to add a tness monitor

or meter if you wish. Fitness monitors can be purchased
at stores that sell biking accessories. Purchase a meter
that can be attached to the HANDLEBAR(2), and follow
any installation and operation instructions provided by
the manufacturer. Your CPS 9190 Indoor Cycle comes
equipped with a MAGNET(73) built into the FLYWHEEL
(23), so it is not necessary to install the magnet that
comes with your meter; just attach the sensor to the
SENSOR CLIP(74) on the MAIN FRAME(1) and
attach the meter to the HANDLEBAR(2) following
manufacturers instructions.

NOTE: Some models of tness monitors/meters may not

attach to the SENSOR CLIP(74). In this case, attach the
sensor to the MAIN FRAME(1) using the sensor bracket
provided by the manufacturer.

MONITOR/METER

(not included)

SENSOR

(Round bar type)

1. Adjust the TENSION KNOB(34) and verify that the Flywheel System provides tension. The Flywheel

System should provide many years of use.

2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that

the left pedal has left hand threads and is tightened by turning counterclockwise. The right pedal has
right hand threads that are tightened by turning clockwise.

3. Verify that the WARNING LABEL(70)

is in place and easy to read. Call Stamina Products immediately at

1-800-375-7520 for a replacement WARNING LABEL(70) if it is missing or damaged.

4. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

5. Worn or damaged components shall be replaced immediately or the CPS 9190 Indoor Cycle removed

from service until repair is made.

6. Only Stamina Products supplied components shall be used to maintain/repair the CPS 9190 Indoor

Cycle.

7. Keep your CPS 9190 Indoor Cycle clean by wiping it off with an absorbent cloth after use.

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or

three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second

heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.

wrist pulse

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower

intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and

build up to higher intensity as you become more aerobically t.

If you feel dizzy or lightheaded you should slow down or stop exercising.

To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.

CONDITIONING GUIDELINES

Target Heart Rate Zone Estimated by Age*

* For cardiorespiratory training benefits, the American College of Sports Medicine recommends

working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the

maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate

20 years

25 years

30 years

35 years

40 years

45 years

50 years

55 years

60 years

65 years

70 years

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute

107-175 beats per minute

105-171 beats per minute

102-166 beats per minute

99-162 beats per minute

97-157 beats per minute

94-153 beats per minute

91-148 beats per minute

88-144 beats per minute

85-139 beats per minute

83-135 beats per minute

200 beats per minute

195 beats per minute

190 beats per minute

185 beats per minute

180 beats per minute

175 beats per minute

170 beats per minute

165 beats per minute

160 beats per minute

155 beats per minute

150 beats per minute

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

13

WARM-UP and COOL-DOWN

Warm-Up

The purpose of warming up is to prepare your body for exercise and to minimize injuries.

Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that

raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place

Stretching

Stretching while your muscles are warm after a proper warm-up and again after your

strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.

Suggested Stretching Exercises

Remember to always check with your physician before starting any exercise program.

Cool-Down

The purpose of cooling down is to return the body to its normal, or near normal, resting

state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be

completed after each strength training session.

Lower Body Stretch

Place feet shoulder-width

apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.

Floor Stretch

While sitting on the oor,

open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder-

width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the oor,

have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

14

LIMITED WARRANTY

WARRANTY

MODEL 15-9190

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and three years on
the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL

NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health

clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the

product's use is in furtherance of a prot making enterprise, and all other use which is not for personal,

family, or household purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE

DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR

BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER

DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state to

state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

15

PRODUCT PARTS DRAWING

16

FRONT

BACK

PART# PART NAME QTY

1 Main Frame 1
2 Handlebar 1
3 Front Stabilizer 1
4 Rear Stabilizer 1
5 Seat Post 1
6 Seat Slider 1
7 Shaft 1
8 Bearing Spacer 1
9 Bearing (6002RS) 2

10 Left Retaining Ring (1 3/8"-24, Left Hand Threads) 1
11 Right Retaining Ring (1 3/8"-24, Right Hand Threads) 1

12 Left Crank 1
13 Right Crank w/ Sprocket 1
14 Flange Nut (M10 x 1.25) 2
15 Crank Cap 2
16 Left Pedal 1
17 Right Pedal 1
18 Chain (1/2" x 1/8" x 112 links) 1
19 Chain Guard 1
20 Inner Chain Guard 1
21 Small Sprocket (16T) 1

22 Retainer (BC 1.29" - 24, Left Hand Threads) 1

23 Flywheel (10kg) 1
24 Left Flywheel Cover 1
25 Right Flywheel Cover 1
26 Flywheel Axle 1
27 Bearing (6000zz) 2

28 Nut (3/8" - 26 x 0.24" thick) 3
29 Nut (3/8" - 26 x 0.35" thick) 1

30 Spacer A 1
31 Spacer B 1
32 Washer (3/8") 2

33 Flange Nut (3/8" - 26) 2

34 Tension Knob 1
35 Support Bracket 1
36 Bushing 1
37 Square Nut (M8 x 1.25) 1
38 Spring 1
39 Collar 1
40 Brake 1
41 Brake Support 1
42 Rubber Pad 1
43 Seat 1
44 Square Plug (30mm x 30mm) 1
45 Slider Bushing 1
46 Locking Knob 1
47 Sleeve 2

PARTS LIST

17

PART# PART NAME QTY

PARTS LIST

18

48 Adjustment Knob 2
49 Wheel 2
50 Rectangular Plug (25mm x 50mm) 4
51 Stand 4
52 Chain Guard Spacer 2
53 Square Washer 1
54 Carriage Bolt (M10 x 1.5 x 45mm) 1
55 Bolt, Button Head (M8 x 1.25 x 15mm) 4
56 Bolt, Socket Head (M5 x 0.8 x 12mm) 6
57 Bolt, Socket Head (M8 x 1.25 x 40mm) 2
58 Bolt, Socket Head (M8 x 1.25 x 40mm, all threaded) 2
59 Screw, Round Head (M5 x 0.8 x 30mm) 2
60 Screw, Round Head (M5 x 10mm) 12
61 Flange Screw, Round Head (M5 x 0.8 x 20mm) 2
62 Nylock Nut (M5 x 0.8) 2
63 Nylock Nut (M8 x 1.25) 2
64 Acorn Nut (M6 x 1) 1
65 Thin Nut (M6 x 1 x 3mm thick) 1
66 Thin Nut (M8 x 1.25 x 5mm thick) 2
67 Nut (M8 x 1.25) 4
68 Washer (M5) 10
69 Washer (M8) 8
70 Warning Label 1
71 Water Bottle Holder 1
72 Screw, Round Head (M5 x 20mm) 1
73 Magnet 1
74 Sensor clip 1
75 Wrench 1
76 Allen Wrench (5mm) 1
77 Manual 1

IMPORTANT : Before lling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

IMPORTANT : We must have your phone number in order to process the order!

Please do not return the product. For your convenience, Stamina's Customer Service Department can be

reached by email at [e-mail] or toll free at 1-800-375-7520 (in the U.S.).

Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central

Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or ll out the fax sheet ordering

form below and fax it to [phone]. Our Customer Service Department will be able to assist you with
your problem and the part will be mailed directly to your house.

Mr./Ms:

Address: Apt. #:

City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )

Date Purchased:

Model #:

Purchased From:

 

PART # DESCRIPTION QUANTITY

 

1 Rear Unit Assembly 1

EXAMPLE:

FAX/MAIL ORDERING FORM

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com