Stamina AVARI GX 8 Owner's Manual

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

www.staminaproducts.com

This Product is Produced Exclusively by

Owner's

Ma nual

75-2000

Pat. Nos. 5,779,598 &

6,063,008

Other patents applied &

are pending

2007, 11

Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

When calling for parts or
service, please specify the
following number.

WA RNING

CAUTION:
Weight on this product should not exceed 300 lbs.

2007 Stamina Products, Inc.

MADE IN TAIWAN

Product May Vary Slightly

From Pictured.

TABLE OF CONTENTS

Page Page

SAFETY INSTRUCTIONS

To reduce the risk of serious injury, read the following Safety Instructions before
using the Avari

GX8 Elliptical Trainer, hereafter referred as the A vari GX8.

WARNING:

Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is e specially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

WARNING:

2

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

Read all warnings posted on the Avari

GX8.

Read this owner's/user's manual and follow it carefully before using the Avari

GX8.

We recommend that two people be available for assembly of this product.
Keep children away from the Avari

GX8. Do not allow children to use or play on the Avari GX8.

Keep children and pets away from the Avari

GX8 when it is in use.
It is recommended that you place this exercise equipment on an equipment mat.
Set up and operate the Avari

GX8 on a solid level surface. Do not position the Avari GX8 on
loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the Avari

GX8.

Inspect the Avari

GX8 for worn or loose components prior to use.

Tighten/replace any loose or worn components prior to using the Avari

GX8.

Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the Avari

GX8.

Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or
crosstraining shoes. Be sure that they fit well, provide foot support and feature non-skid rubber
soles.
Be careful to maintain your balance while using, mounting, dismounting, or assembling the Avari
GX8, loss of balance may result in a fall and serious bodily injury.
Keep both feet firmly and securely on the pedal caps while exercising.
The Avari

GX8 should not be used by persons weighing over 300 pounds.

The Avari

GX8 should be used by only one person at a time.

The Avari

GX8 is for consumer use only. It is not for use in public or semipublic facilities.

Use two people to move the Avari

GX8.

Safety Instruction s 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Set Up Instructions 12
Operational Instructions 13
Computer Instructions 17
Storage 23

Maintenance 23
Troubleshooting 24
Conditioning Guidelines 25
Warm-Up and Cool-Down 26
Warranty 27
Product Parts Drawing 28
Parts List 29
Fax/Mail Ordering Form 31

THANK YOU FOR PURCHASING THE

Avari

GX8 Elliptical Trainer

To help you get started, we have pre-assembled most of your
Avari GX8 Elliptical Trainer at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into sha pe

and on your way to achieving a happier and healthier lifestyle.

3

Should you have any que stions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M. Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

CALL US FIRST

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

BEFORE YOU BEGIN

4

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :

Handlebar

Upright

Battery

Warning Label

Nose Covers

Left Pedal Arm

Pedal Cap

Handlebar

Pedal Divider

Crank Disc

Covers

Wheel

Rear Stabilizer

Pedal Ca p

Link

Tray

Pulse Sensor

Thank you for choosing the Avari GX8. We take
great pride in producing this quality product and hope
it will provide many hours of quality exercise to ma ke
you feel better, look better a nd enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time

and opportunity to exercise. The Avari

GX8

provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and fa mili arize yoursel f with the parts that are
labeled.

Read this manual carefully bef ore using the Avari

GX8.

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with

the parts included with your Avari

GX8, plea se do
not return the product. Contact us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T i me) on Friday.
If you would like to contact us online, go to our
website at www.sta mina products.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.

Roller Cover

Main Frame

Right Pedal Arm

Socket Wrench
Allen Wrench (5mm)
Allen Wrench (6mm)

ATTENTION: Use only NiMH

(Nickel Metal Hydride) rechargeable
batteries with this product. The
higher voltage from other types of
batteries may damage this
equipment. Failure to use NiMH
rechargeable batteries will void your
warranty and may result in damage
to your machine. Stamina is not
responsible for non-complia nce with
correct battery usage.

Rocker Arm

Computer

Warning Label

5

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the Avari GX8. Plea se take a moment
to fa miliarize yourself with all of the warning & notice labels.

Labels are a ctual size

BA TTERY W ARNING LABEL(96)

W2

WAR NING LABEL(95)

W1

Part No. and Description Qty

6

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
end of the bolts, or screws on the circles to check for the corre ct diameter. Use the small scale to check the
length of the bolts and screws.

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

mm.

in.

INCHES

MILLIMETERS

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

6 8 10 12

3/16" 5/16" 1/2"3/8"1/4"

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

62 Bolt, Button Head (M6 x 1 x 12mm) 4
63 Bolt, Button Head (M6 x 1 x 16mm) 8
64 Bolt, Button Head (M10 x 1.5 x 25mm) 2

77 Washer (M6) 4
78 Washer (M10) 6

84 Nylock Nut (M10 x 1.5) 4

65 Bolt, Socket Head (M6 x 1 x 12mm) 8

70 Screw, Round He ad (M5 x 0.8 x 15mm) 12
71 Screw, Round He ad (M5 x 0.8 x 35mm) 5

75 Lock Wa sher (M6) 8
76 Lock Wa sher (M10) 2

79 Nut (3/8" - 16) 3

53 Clamp W asher (M6) 8

STEP 2: Thread the NUTS(3/8"-16)(79) all the way to the bottom of the threa ded rod on the STANDS(59).

Lift the front stabilizer on the MAIN FRAME(1) and place a temporary spacer (wood block or thick book)
under the front of the MAIN FRAME(1). Thread the three STANDS(59) into the MAIN FRAME(1). Remove
the temporary spacer.

NOTE:

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at: [e-mail]

7

ASSEMBLY INSTRUCTIONS

STEP 1: Attach the REAR STABILIZER(2) to the MAIN FRAME(1) with BUTTON HEAD BOLTS

(M10x1.5x25mm)(64), WASHERS(M10)(78), a nd LOCK W ASHERS(M10)(76).

See page 12 for detailed leveling instructions to prevent rocking.

Make the tab face down

for assembly.

Lift from the

Front Stabilizer

It will be easier to attach the PEDAL CAPS(29L, 29R) to the PEDAL ARMS(6, 7) by raising the
PEDAL ARMS(6,7) and then attaching the PEDAL CAPS(29L, 29R). Please have a partner hold

the raised pedal arm a s you atta ch the PEDAL CAPS(29L, 29R). This way you are not lying on the
floor trying to attach the PEDAL CAPS(29L, 29R).

STEP 4: Attach the PEDAL CAP(29L) to the LEFT PEDAL ARM(6) and the PEDAL CAP(29R) to the

RIGHT PEDAL ARM( 7) with SOCKET HEAD BOLTS(M6x1x12mm)(65).
NOTE:

STEP 3: Ma ke the tab in the edge of the OV AL ENDCAPS(58) fa ce down, then press the OV AL ENDCAPS

(58) into both ends of the front stabilizer of the MAIN FRAME(1).

R

L

ASSEMBLY INSTRUCTIONS

8

STEP 5

CAUTION:

Attach the UPRIGHT(3) to the MAIN FRAME(1) with the NYLOCK NUTS(M10x1.5)(84) and WASHERS
(M10)(78). Plug the BASE CONNECTION WIRE(18) into the CONNECTION WIRE(19).

STEP 6

Connect the LINKS(36) to the ROCKER ARMS(4) at both sides with D-SHAPED SHAFT(42), WASHERS
(M6)(77), and BUTTON HEAD BOLTS(M6x1x12mm)(62).

Be careful not to damage the BASE CONNECTION WIRE(18) and CONNECTION WIRE(19)
when asse mbling the UPRIGHT(3).

ASSEMBLY INSTRUCTIONS

STEP 7

Place the LEFT NOSE COVER(34) and RIGHT NOSE COVER(35) at both sides of the UPRIGHT(3). Bolt
the nose covers together with the ROUND HEAD SCREW(M5x0.8x35mm)(71) on the top. Then slide the
nose covers down and atta ch them to the MAIN FRAME(1) with ROUND HEAD SCREW(M5x0.8x35mm)(71).

STEP 8

Refer to the inset drawing. Lift up the RIGHT PEDAL ARM(7) slightly. Then place a ROLLER COVER(33)
to cover the ROLLER(30). Snap the ROLLER COVER(33) into the slots at both sides of the ROLLER(30)
in the MAIN FRAME(1). Repeat on the left side.

9

Slot

ASSEMBLY INSTRUCTIONS

10

STEP 9

Attach the TRAY(56) to the bracket on the UPRIGHT(3) and secure with ROUND HEAD SCREWS
(M5x0.8x15mm)(70).

STEP 10

Attach the PIVOT ENDCAPS(51) to the PIVOT CUFF BUSHINGS(45) at both sides with ROUND HEAD
SCREWS(M5x0.8x15mm)(70).

STEP 1 1

Slide the HANDLEBAR SLEEVE(52) onto the HANDLEBARS(5). Insert the HANDLEBARS(5) onto the
ROCKER ARMS(4) a nd secure with BUTTON HEAD BOL TS(M6x1x16mm)(63), CLAMP W ASHERS(M6)
(53), and LOCK WASHERS(M6)(75). Slide the HANDLEBAR SLEEVE(52) down to cover the bolts on the
HANDLEBARS(5).

ASSEMBLY INSTRUCTIONS

11

STEP 12

Install four AA NiMH (Nickel Metal Hydride) re chargeable batteries into the COMPUTER(20). Connect the
CONNECTION WIRE(19) and the PULSE SENSOR WIRES(89) to the COMPUTER(20). Slide the
COMPUTER(20) onto the bracket on the UPRIGHT(3) and secure with ROUND HEAD SCREWS
(M5x0.8x15mm)(70).
CAUTION:

Be careful not to damage the CONNECTION WIRE(19) and PULSE SENSOR WIRES(89)
when attaching the COMPUTER(20).

ATTENTION: Use only NiMH
(Nickel Metal Hydride) rechargeable
batteries with this product. The
higher voltage from other types of
batteries may damage this
equipment. Failure to use NiMH
rechargeable batteries will void your
warranty and may result in damage
to your machine. Stamina is not
responsible for non-complia nce with
correct battery usage.

SET UP INSTRUCTIONS

LEVELING:

MOVING:

Equipment Mat

Place the Avari GX8 in the area where it will be used. It is recommended that the Avari GX8 be placed
on an equipment mat. The maximum usage dimensions of Avari

GX8 are approximately 99 1/4" long x
25 5/8" wide x 64 7/8" tall. (These dimensions may vary up to one inch.) An area 4 feet wide x 9 feet long is
required for safe operation of the Avari

GX8. Make sure that a dequate space is available f or a ccess to and

pa ssage around the Avari GX8.

Adjust the STANDS(59) under the MAIN FRAME(1) so that the Avari

GX8 sits on the floor
without rocking. Refer to the instructions below the illustration.
Move the Avari

GX8 with the moving wheels on the REAR STABILIZER(2). Lift from the

Front Stabilizer of the MAIN FRAME(1). Two people are required to move the Avari

GX8.

12

Lift up from the Front
Stabilizer for moving.

FUNCTION INSPECTION:

Visually inspect the Avari GX8 to verify that assembly is as shown in the above illustration. Check the
function of the Avari

GX8. Stand on the f oot pedals and place your hands at a comfortable position on the
handlebars. Slowly move your highest foot forward and follow the natural path of the machine. Turn the
crank slowly through one complete revolution to verify that the drive train functions properly . Use the "

Quick

Start

" and "+/-" button s on the COMPUTER(20) to select a program and verify that the Generator Syste m

provides different tensions. Refer to the COMPUTER INSTRUCTIONS on page s 17 to 22.

Locate and read the W AR NING LABEL(95) on the Avari

GX8. Make sure that all users re ad

the W AR NING LABEL(95).

CAUTION:

To level the Avari GX8, first screw the STAND(59) located in
the middle of the MAIN FRAME(1) all the way up into the
MAIN FRAME(1) so that it is not touching the floor.

Adjust the four STANDS(59) on each of the four
corners, two under REAR ST ABILIZER(2) and
two under the front of the MAIN FRAME(1).

When all four are adjusted and the Avari

GX8

is stable, tighten the NUTS(3/8"-16)(79) against
the MAIN FRAME(1) and REAR STABILIZER(2)
to lock the STANDS(59) into position.
While you are adjusting these four STANDS(59),
the one STAND(59) located in the middle of the
MAIN FRAME(1) must not be in contact with the floor.

Only after the Avari

GX8 ha s been stabilized with
the four STANDS(59) on the corners will you
position the middle STAND(59) so it is in
contact with the floor to provide extra
stability for the MAIN FRAME(1).

13

OPERATIONAL INSTRUCTIONS
PEDAL DIVIDER ADJUSTMENT

EXERCISE WORKOUT

1.2.Press down the PUSH BUTTON(91) a nd press the PEDAL DIVIDER(90) down slightly to slide the PEDAL

DIVIDER(90) to new position. Release the button to lock the PEDAL DIVIDER(90) in position. Refer to

illustration A.

HINT :

Press down the PUSH BUTTON(91) and slide the PEDAL DIVIDER(90) to middle of the PEDAL CAP(29).
Lift up the PEDAL DIVIDER(90) and turn it 180 degrees. Slide the PEDAL DIVIDER(90) to the back of
the PEDAL CAP(29). Refer to illustration B.

Do not try to lift up the PEDAL DIVIDER(90) when sliding it. It will be easier to adjust without
lifting it.

The PEDAL DIVIDER(90) position ca n be a djusted to fit your shoes. You may select the front or the back of
the

PEDAL CAPS(29) for foot pla ce ment. Y ou will have le ss vertical movement in the elliptical stride if you

place your feet at the front of the

PEDAL CAPS(29).

Illustration A) PEDAL DIVIDER(90) at front Illustration B) PEDAL DIVIDER(90) at back

Your Avari GX8 is self powered meaning the pedaling action of your workout powers the computer
monitor no electric power source or cords are needed. The four AA rechargeable NiMH (Nickel Metal
Hydride) batteries that are included serve as your backup power source. Use only NiMH (Nickel Metal
Hydride) rechargeable batteries with this ma chine. Failure to do so will void your warra nty a nd may result in
da mage to your machine.

These rechargeable batteries only hold their charge for three to four weeks after fully charged;
therefore, the batteries will not be charged when you assemble and use your

Avari GX8 for the

first time so to charge the batteries will require a 30 minute workout. After that initial workout, the
batteries will be charged (a s long as you don't let your machine remain idle for three to four weeks)

and your monitor a nd workout progra ms will be availa ble every time you step on your

Avari GX8.

To start using the Avari

GX8, stand on the foot pedals, grasp the handlebars, move your highest foot

forward and follow the natural path of the machine.
Start at a load level that is comfortable to familiarize yourself with the machine. Once you are comfortable,

start adjusting the load level to achieve the workout desired.

NOTE:

14

OPERATIONAL INSTRUCTIONS (continued)

HEART RATE MONITORING

To get the maximum benefit from your Avari GX8 workout it is important that you exercise within your
target heart rate zone for at lea st 20 minutes. Re search ha s shown that working out below your target heart
rate zone won't burn fat or improve your cardiovascular fitness, and working above your target heart rate
zone is also counter productive.

Everyone has their own target heart rate zone and exercising within that zone should be your goal every
time you work out. Finding your personal target heart rate zone is calculated by:

The

Avari GX8 can measure how hard you are exercising in two ways:

PULSE MONITOR V. HEART RATE TRANSMITTER

Load Level Adjustment

The load level of Avari GX8 can be changed at any time during your workout. Adjusting the load level will
allow you to increase or decrease your intensity level.

Forward and Reverse

The Avari GX8 can be used in the forward and reverse direction to vary the muscles that you work out.
This will also vary your workout helping you to stay motivated. To change directions, si mply slow the pedals
down until they stop and switch directions.

Find your maximum heart rate with this simple formula:
220 - Age = predicted maximum heart rate
Example: A 40-year-old would have a predicted maximum heart rate of
180 beats per minute, 220 - 40 = 180.
Your target heart rate zone is a range that is 55% to 90% of your
maximum heart rate.*
Predicted Maximum Heart Rate x .55 = lower end of target heart rate zone
Predicted Maximum Heart Rate x .90 = upper end of target heart rate zone
Example: A 40-year-old would have a Target Heart Rate Zone of 99 to
162 beats per minute; 180 x .55 = 99. 180 x .90 = 162.

See page 24 of this Owner

's Manual for more conditioning guidelines including a chart of target

Heart Rate Zones Estimated by Age.

* For cardiorespiratory training benefits, the American College of Sports Medicine recommends
working out within a heart rate range of 55% to 90% of maximum heart rate.

STEP 1:

STEP 2:

NOTE:

1. By measuring your pulse

2. By monitoring your heart rate

Your pulse is monitored by four Pulse Sensors that are built into both the left and right Hand Grips, two in
each grip. Your pulse reading gives you a snapshot of how hard your heart is working at that point in your
workout by measuring the number of heart beats per minute. Please note that pulse sensors provide less
accurate inf ormation tha n the he art rate transmitter and pulse sensors don

't monitor your heart rate during

your entire workout; the heart rate transmitter does monitor your heart rate for the endurance of your
workout.

15

OPERATIONAL INSTRUCTIONS (continued)

Using the Heart Rate Transmitter Chest Strap

The HEART RATE TRANSMITTER(97) worn around the chest is powered by a 3V LITHIUM BATTERY
(CR2032)(101) located in the center of the stra p. Two electrodes on either side of the battery monitor your

heartbeat, and an adjustable elastic strap holds the transmitter in place. The receiver built into the

Avari

GX8 picks up your heart rate from the HEART RATE TRANSMITTER(97) and displays it on the monitor

during your workout.

NOTE: Apply water or conductive gel to moisten the
ribbed rubber area covering the electrodes. This ribbed
area must be wet and in contact with your chest skin to
properly detect your heart rate.

The HEART RATE TRANSMITTER(97) worn around your chest sends your heart rate information to a
receiver in your computer monitor so your heart rate is tra cked while you exercise. This is the most reli able
way to measure your heart rate to make sure you are exercising within your target heart rate zone so you
get the most out of your workout time.

Dry your hands to prevent slipping.
Make sure both hands are in contact with all four sensors (two in each hand).
Grasp the sensors firmly.
Apply constant pressure to the sensors until you get a con sistent reading on your computerized workout
console screen.

Using the Pulse Sensors

To get the most accurate reading from the Pulse Sensors, follow these steps.

To assemble the HEART RATE TRANSMITTER(97),
insert the 3V LITHIUM BATTERY(CR2032)(101) as
shown in the illustration, place the BA TTER Y RUBBER
RING(99) and BA TTER Y COVER(100) properly into the
case, then close the cover, tightening it with a coin or
similar opener.

Attach the ELASTIC STRAP(98) by in serting the heart-sha ped tabs through the openings in the tra nsmitter
and twisting. Adjust the ELASTIC STRAP(98) to fit your chest snugly as shown in the illustration below.

(97) Heart Rate Transmitter

(101) 3V Lithium Battery

(100) Battery Cover
(99) Battery Rubber Ring

(98) Elastic Strap

close

open

Ma ke sure to close the BA TTERY COVER(100)
very tightly as illustrated to prevent sweat and
moisture from damaging the battery.

NOTE:

(97) Heart Rate Transmitter

(98) Elastic Strap

Heart-shaped Tab

To en sure a secure conne ction a bove, be sure that the front
edge of the Heart-sha ped tab is completely inside of the he art­shaped opening on the HEART RATE TRANSMITTER(97).

Transmission LED Indicator

For checking operation of tran smitter, the red LED indicator will fla sh indicating the tra nsmitter is in operation.
Adjust the transmitter position to keep the LED indicator flashing consistently for accurate readings. (See
illustration below.)

OPERATIONAL INSTRUCTIONS (continued)

16

If your heart rate is inconsistent or not tracking on your workout console, do the following:

NOTE:

Moisten the grooved electrode areas on the back of the chest strap again and make sure they
are in contact with the skin. Y our s kin may be dry when you begin your workout a nd the moisture
is necessary to ensure contact. As you sweat, contact will improve.
Tighten the elastic strap so it remains in place a s you exercise. Move ment of the electrodes will
result in inaccurate or erratic signal and readings.
Clean the electrodes as dirt can interfere with transmission. Use a mild soap and water and dry
with a soft towel.

Wash regularly with mild soap and water solution and dry with a soft towel being careful not to abrade
the electrodes.
Store in a cool, dry place. Make sure the electrodes aren't stored with any wet material a nd never store
a wet transmitter in non-breathable material like a plastic bag or sports bag.
Do not bend or stretch the transmitter.

Transmitter Care and Maintenance

LED Indicator

COMPUTER INSTRUCTIONS

BUTTONS

Quick Start: Press this button to start working

out in a manual workout profile.

Cool Down: Press this button to go into a 'Cool

Down' workout profile.

Stop: Press this button once to pause your

workout session. Press this button twice to reset
the computer.

Level: Press this button to select your desired

workout level 1-25.

Time: Press this button to select your desired

workout time.

Your Avari

GX8 Elliptical Trainer workout is controlled by an advanced computer system. Use the

pre-programmed Basic, Advanced or Interactive workout profiles to vary your workouts from session to
session, or use the Quick Start workout and set your own pa ce. Whatever workout you choose, the computer
monitor will track and display your time, distance, calories burned, and heart rate information to keep you
motivated and on track to achieve your fitness goals.

+/-: Press these buttons to increa se/decrea se your

time, level. Y ou will also press a ny of these buttons
to select your desired workout profile when
prompted from the scrolling message center.

Select: Press this button to input the displayed

screen value.

Basic: Press this button to go to the "Basic"

workouts selection window.

Advanced: Press this button to go to the

"Adva nced" workouts selection window.

Interactive: Press this button to go to the

"Interactive" workouts selection window.

17

COMPUTER INSTRUCTIONS

LCD DISPLAY INSTRUCTIONS

A Scrolling Message Center: Displays both user instructions and workout

para meters throughout the workout.

B Watts/Level: Displays the amount of power or resistance level being exerted.
C Segment Time: Displays the amount of time spent in e ach segment of the workout.
D Calories: Displays the amount of kcal burned by the user.
E Time: Displays the total amount of time used during the workout. Can count up or

down.

F Distance/Speed: Displays both the distance traveled and the speed of the user

alternately.

G RPM: Displays the user's actual number of pedal revolutions per minute.
H Heart Rate: Displays the user's actual heart rate when using the heart rate sensor

or the included telemetry heart strap.

I HR%/Time In Zone: Alternately displays the user's actual percent of achieved

heart rate goal and the total amount of time that the user is at their goal when using
the heart rate sensor or the included telemetry heart strap.

18

A

F

B

C

E

D

G

H

I

COMPUTER INSTRUCTIONS
PROGRAM DESCRIPTIONS

A. Ba sic Workouts

B. Advanced Workouts

C. Interactive Workouts

19

COMPUTER INSTRUCTIONS

20

PROGRAM DESCRIPTIONS (continued)

A. Ba sic Workouts

C. Interactive Workouts

1. Hill: Incre a sing interval resistance levels (hills) that have brief resista nce level reductions between

increases, followed by a plateau of a steady state resistance level and then a gradual cool-down.

2. Hike: Slow , ste ady increa se in resista nce levels to a pea k value (ba sed upon level chosen) a nd

then a slow steady decrease in resistance levels to a valley.

3. Speed Change: The message center prompts the user to perform increases and decrea ses in

RPM (every 30 seconds) to simulate interval speed and resistance level training.

4. Random: Increases in resistance levels (hills) followed by "random" decreases in resistance

levels (valleys). Both the increases/decreases and duration of the changes are random.

5. Ascent: Moderate, ste ady increa se in resista nce level to a peak value (ba sed upon level chosen)

and then a slow steady decrease in resistance level to a valley.

6. Manual: User controls the resistance level.

B. Advanced Workouts

1. Fat Burn: Resistance levels automatically increase/decrease to keep user's heart rate at 65%

of ACSM (American College of Sports Medicine) theoretical max.

2. Peaks & Valleys: Resistance levels moderately increase and decrea se to keep user's heart
rate moving back and forth between 65% and 80% of ACSM theoretical max.

3. Switch Back: Resistance levels rapidly increase and decrease to keep user's heart rate
moving between 65% and 80% of ACSM theoretical max.

4. Cardio: Resistance levels automatically increase and decrease to keep user's heart rate at
80% of ACSM theoretical max.

5. Pace: The message center prompts the user to increase heart rate by increasing and
decreasing RPM to achieve user's heart rate at 70% of ACSM theoretical max.

1. Push-Pull: Prompts the user to concentrate on alternately pushing and pulling with their

upper body over a given time period.

2. Kick-It: Prompts the user to increase speed (after two minute warm-up) to plus 20 RPM over

warm-up speed for one minute, then prompts the user to reduce by 10 RPM for one minute. The
user continues to increase RPM by 20 for one minute and decrease RPM by 10 for one minute
until reaching a maximum RPM. After reaching the maximum RPM the user then begins to
decrease RPM by 20 for one minute and then increase RPM by 10 for one minute. This
decreasing pattern repeats until the user is back at his starting warm-up RPM. This is a finite
program that goes up to a max of 90 RPM based on the total time entered.

3. Total Body: Prompts the user to concentrate on pushing and pulling with upper body, as

well as changing direction (forward and backward) and using lower body only.

4. Back & Forth: Prompts the user to change direction back and forth over a given time

period.

COMPUTER INSTRUCTIONS

21

PROGRAM INSTRUCTIONS

1) Press the "Quick Start" button

2) Enter your weight using the "+" or "-" keys. Or wait five seconds and the computer will default to
150 lbs.

3) Enter your level using the "+" or "-" keys. Or wait five seconds and the computer will default to
Level 1.

4) Enter your time using the "+" or "-" keys. Or wait five seconds a nd the computer will default to 20
minutes.

5) Begin your workout after the starting countdown.

6) At any time during the workout you can press the "Stop" button to pause your workout for up to
one minute. After one minute the computer will re set itself if you have not started to work out again.

7) Pressing the "Stop" button twice will reset the computer immediately.

1) Press the "Basic" button and follow the on-screen instructions or read the following printed
instructions.

2) Enter your desired Basic workout profile and press the "Select" button. Note: If you don't press
the "Select" button the profile will be automatically selected in three seconds

3) Enter your weight using the "+" or "-" keys. Or wait five seconds and the computer will default to
150 lbs.

4) Enter your level using the "+" or "-" keys. Or wait five seconds and the computer will default to
Level 1.

5) Enter your time using the "+" or "-" keys. Or wait five seconds a nd the computer will default to 20
minutes.

6) Begin your workout after the starting countdown.

7) At any time during the workout you can press the "Stop" button to pause your workout for up to
one minute. After one minute the computer will re set itself if you have not started to work out again.

8) Pressing the "Stop" button twice will reset the computer immediately.

9) At any time during the workout you can press the "Basic", "Advanced", or "Interactive" buttons to
change your workout profile. Please refer to the Basic, Advanced, or Interactive sections of this
manual for the corresponding workout instructions.

A. QUICK START

B. BASIC WORKOUTS: HILL, HIKE, SPEED CHANGE, RANDOM, ASCENT, MANUAL

COMPUTER INSTRUCTIONS

22

PROGRAM INSTRUCTIONS (continued)

1) Press the "Interactive" button and follow the on-screen instructions or read the following printed
instructions.

2) Enter your desired Interactive workout profile and press the "Select" button. Note: If you don't
press the "Select" button the profile will be automatically selected in three seconds.

3) Enter your age using the "+" or "-" keys. Or wait three seconds and the computer will default to 35
years of age.

4) Enter your target heart rate(THR) using the "+" or "-" keys. Or wait three seconds and the computer
will default to 120 Beats Per Minute(BPM).

5) Enter your weight using the "+" or "-" keys. Or wait three seconds a nd the computer will default to
150 lbs.

6) Enter your time using the "+" or "-" keys. Or wait three seconds and the computer will default to
20 minutes.

7) Begin your workout after the starting countdown.

8) At any time during the workout you can press the "Stop" button to pause your workout for up to
one minute. After one minute the computer will re set itself if you have not started to work out again.

9) Pressing the "Stop" button twice will reset the computer immediately. At any time during the
workout you can press the "Basic", "Advanced", or "Interactive" buttons to change your workout
profile. Plea se refer to the Ba sic, Adva nced, or Interactive se ctions of this manual for the corre sponding
workout instructions.

1) Press the "Advanced" button and follow the on-screen instructions or read the following printed
instructions.

2) Enter your desired Advanced workout profile and press the "Select" button. Note: If you don't
press the "Select" button the profile will be automatically selected in three seconds.

3) Enter your weight using the "+" or "-" keys. Or wait five seconds and the computer will default to
150 lbs.

4) Enter your level using the "+" or "-" keys. Or wait five seconds and the computer will default to
Level 1.

5) Enter your time using the "+" or "-" keys. Or wait five seconds a nd the computer will default to 20
minutes.

6) Begin your workout after the starting countdown.

7) At any time during the workout you can press the "Stop" button to pause your workout for up to
one minute. After one minute the computer will re set itself if you have not started to work out again.

8) Pressing the "Stop" button twice will reset the computer immediately.

9) At any time during the workout you can press the "Basic", "Advanced", or "Interactive" buttons to
change your workout profile. Please refer to the Basic, Advanced, or Interactive sections of this
manual for the corresponding workout instructions.

C. ADVANCED WORKOUTS: PUSH-PULL, KICK-IT, TOTAL BODY, BACK & FORTH

D. INTERACTIVE WORKOUTS: FAT BURN, PEAKS & VALLEYS, SWITCH BACK, CARDIO,
PACE

23

MAINTENANCE

The safety and integrity designed into the Avari GX8 can only be maintained when the Avari GX8 is
regularly examined for damage and wear. Special attention should be given to the following:

Use the "

/ " buttons on the COMPUTER(20) to select a progra m a nd verify that the Generator Syste m
provides different tensions. The Generator System should provide many years of use.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Verify that the Warning Labels are present a nd legible. Repla ce the W arning Labels if they are missing or
damaged.
Verify that all nuts, bolts, a nd knobs are present a nd properly tightened. Repla ce missing nuts, bolts, a nd
knobs. Tighten loose nuts, bolts, and knobs.
Worn or da maged components shall be re placed immediately or the

Avari GX8 removed from service

until repair is made.
Only Sta mina Products supplied components shall be used to maintain/repair the

Avari GX8.

Keep your

Avari GX8 clean by wiping with an absorbent cloth after use.

1.

2.

3.

4.

5.

6.

7.

To store the

Avari GX8 simply keep it in a clea n dry place.

The

Avari GX8 is approxi mately 89 3/8" long x 25 5/8" wide x 64 7/8" tall. These di men sions may vary.

Plea se me asure your

Avari GX8 if exact dimen sion s are needed.

Move the

Avari GX8 with the moving wheels on the REAR STABILIZER(2). Lift from the Front Sta bilizer

of the MAIN FRAME(1) to move the

Avari GX8. Two people are required.

To avoid damage to the COMPUTER(20), remove the batteries before storing the

Avari GX8 for one

year or more.

1.

2.

3.

4.

STORAGE

Remove snap ring and link to expose Pedal Lever Bearing. Use lithium grease to coat the inside of the
bearing. Replace snap ring. Repeat on the other side.

NOTE:

Contact your Customer Service Representative for assistance.

24

TROUBLESHOOTING

With a little care, your Avari GX8 will give you many years of trouble-free use. Our customer service
representatives are available to help you with your questions about your machine. Following are some
maintenance troubleshooting tips to keep your

Avari GX8 in top operating condition.

Monitor Lighting Inconsistencie s

If your monitor's lighting is uneven or dim, try the following solutions.

Dead Monitor Screen

If the monitor doesn't come on when you press the Quick Start button, then ma ke sure that all connections
are secure by checking:

Noise From Front of Machine

Any kind of clacking or clicking noise from the front of the Avari GX8 during use could be caused by a
loose connection in one or both of the LINKS(39).

Contact your Customer Service Representative for parts and f or assistance.

Pedal Lever Bearing Squeaking

The Pedal Lever Bearings are located at the end of the RIGHT PEDAL ARM(7) a nd LEFT PEDAL ARM(6)
where they connect to the CRANK DISC(23). If you hear squeaking from this area:

Do not spray the bearing with lubricant. Although this may stop the squeaking short term, it will
not solve the squeaking issue.

T ension Adjustment

Your Avari GX8 is programmed to adjust the pedal re sista nce a ccording to the workout level you choose.
Level one ha s very little tension and is easier to pedal whereas level twenty ha s high ten sion and is the most
difficult to pedal.

Rocking

If your Avari GX8 rocks during your workout, first check to ma ke sure your ma chine is level as described
on page 12.

If the machine a ppe ars to be level yet still rocks, it could be caused by a loose connection in the

LINKS(36) that connect to the bottom of the ROCKER ARMS(4).

Replace LINKS(36). See STEP 6 in the Assembly Instruction on page 8. Contact customer service for
part and replacement instructions.

Inside the monitor by removing the front of the monitor a nd checking the wires where they connect being
careful not to pull on wires, just on the plugs.
The connection that runs up through the UPRIGHT(3). See STEP 5 in the Assembly Instructions on
page 8.
The rechargeable batteries.
Since the

Avari GX8 is self powered, it may be necessary to pedal for a few minutes to re-power the

batteries to start the monitor. This is especially true if the machine hasn

't been used for an extended

period of time.
Contact your Customer Service Representative for assistance.

Check the batteries to see if they need to be replaced.
Check all wire connections inside monitor a nd at the ba se of the monitor where it connects to UPRIGHT(3).
When checking connections, be sure not to pull on wires as this might loosen the connection. Instead,
hold the plug at the connection.
Call your Customer Service Representative for assistance.

If your machine has too much tension in the lower levels or not enough tension in the higher levels,
contact a customer service representative for assistance.

25

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually, too, by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone f or a few minutes; however, your aerobic
ca pa city will improve over the next six to e ight weeks. It is i mporta nt to pa ce yourself while you exercise so
you don’t tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingers on your wrist and take a six second heartbeat count. Multiply the
results by ten to find your heart rate. For exa mple, if your six second he artbeat
count is 14, your heart rate is 140 beats per minute. A six second count is
used because your heart rate will drop rapidly when you stop exercising.
Adjust the intensity of your exercise until your heart rate is at the proper level.

wrist pulse

Have your doctor review your training and diet programs.
Begin your training progra m slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower inten sity and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.

Target Heart Rate Zone Estimated by Age*

Remember to follow these e ssentials:

To determine if you are working out at the correct intensity, use a he art rate monitor or use the table below .
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting a n exercise program, work out at the low end of your target heart
rate zone. As your a erobic ca pacity i mproves, gradually increa se the intensity of your workout by incre a sing
your heart rate.

For cardiorespiratory training benefits, the American College of Sports Medicine re commends working
out within a heart rate range of 55% to 90% of maxi mum he art rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate

*

20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute

200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

26

WARM-UP and COOL-DOWN

Warm-up The purpose of warming up is to prepare your body f or exercise and to mini mize injuries. W arm

up for two to five minutes before strength-training or aerobic exercising. Perform activities that raise your
heart rate and warm the working muscle s. Activitie s may include brisk walking, jogging, jumping ja cks, jump
rope, and running in place

Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength

or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevated temperature, which greatly reduces the risk of in jury . Stretches should be held for 15 to 30 seconds.
Do not bounce.

Suggested Stretching Exercise s

Remember always to check with your physician before starting any exercise program.

Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state

at the end of ea ch exercise se ssion. A proper cool-down slowly lowers your heart rate a nd allows blood to
return to the heart. Y our cool-down should include the stretche s listed above a nd should be completed after
each strength-training session.

Lower Body Stretch

Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessen, try a lower
position gradually.

Floor Stretch

While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder­width a part and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the floor,
have legs apart one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of one year on the parts and five years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, fa mily, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Stamin a Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 [phone]. If the defect is covered under this limited
warranty , you will be requested to return the product or part to us f or free repair or repla cement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE T O YOU. In the event that the purchaser makes a ny clai m under this

limited warranty or a ny implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date and place of purchase.

Stamin a Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or express warranty given by Stamina Products, Inc. This warra nty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers and li mitations of a nd on implied warranties a nd
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

27

WARRANTY

LIMITED WARRANTY

MODEL 75-2000

PRODUCT PARTS DRAWING

28

FRONT

BACK

PARTS LIST

DIAGRAM# PART NAME QTY

1 Main Frame 1
2 Rear Stabilizer 1
3 Upright 1
4 Rocker Arm 2
5 Handlebar 2
6 Left Pedal Arm 1
7 Right Pedal Arm 1
8 Shaft 1
9 Pulley 1
10 Bearing (6004z) 2
11 Washer (ø 21 x ø30x 1mm thick) 16
12 C Ring (20mm) 6
13 V-Ribbed Belt (1428J8) 1
14 Hybrid Generator 1
15 Low Control Board 1
16 Generator Control Wire 1
17 Generator Power Wire 1
18 Ba se Connection Wire 1
19 Connection Wire 1
20 Computer 1
21 Left Cover 1
22 Right Cover 1
23 Crank Disc 2
24 Crank 2
25 Flange Nut (M14 x 2.0) 2
26 Pedal Arm Bushing (25mm ID) 4
27 Shaft Cap 2
28 Pedal Arm Plug 2
29 Pedal Cap 2
30 Roller 2
31 Bearing (6000ZZ) 4
32 Shaft Bolt 2
33 Roller Cover 2
34 Left Nose Cover 1
35 Right Nose Cover 1
36 Link 2
37 Spherical Bearing 2
38 Inner Retaining Ring (26mm) 2
39 Pivot Shaft 2
40 Pivot Spa cer 2
41 Low Rock Arm Bushing 4
42 D-Shaped Shaft 2
43 Endcap (38mm) 2
44 Pivot Cuff 2
45 Pivot Cuff Bushing 2
46 C Ring (25mm) 4
47 Pivot Shaft Spacer 2
48 Large Washer (ø26 x ø34 x 1mm thick) 6
49 Wave Washer (25mm) 2
50 Rock Arm Bushing 4
51 Pivot Endcap 2
52 Handlebar Sleeve 2
53 Clamp Washer (M6) 8

29

PARTS LIST

DIAGRAM# PART NAME QTY

30

54 Foam Grip 2
55 Round Plug (31.8mm) 2
56 Tray 1
57 T ray Bottom Cover 1
58 Oval Endcap 4
59 Stand 5
60 Wheel 2
61 Barrel Nut (M6 x 1.0 threaded, 35mm long) 2
62 Bolt, Button Head (M6 x 1 x 12mm, with nylock) 10
63 Bolt, Button Head (M6 x 1 x 16mm, with nylock) 8
64 Bolt, Button Head (M10 x 1.5 x 25mm) 2
65 Bolt, Socket Head (M6 x 1 x 12mm) 8
66 Bolt, Round Head (M6 x 1 x 10mm) 2
67 Bolt, Flat Head (M6 x 1 x 15mm) 4
68 Bolt, Hex Head (M8 x 1.25 x 15mm) 4
69 Bolt, Hex Head (M8 x 1.25 x 40mm) 2
70 Screw, Round Head (M5 x 0.8 x 15mm) 17
71 Screw, Round Head (M5 x 0.8 x 35mm) 5
72 Screw, Round Head (M3 x 35mm) 4
73 Screw, Round Head (M4 x 12mm) 8
74 Screw, Round Head (M5 x 18mm) 15
75 Lock Washer (M6) 8
76 Lock Washer (M10) 2
77 Washer (M6) 8
78 Washer (M10) 6
79 Nut (3/8" - 16) 5
80 Nut (M8 x 1.25) 2
81 Thin Nylock Nut (M8 x 1.25) 4
82 Nylock Nut (M6 x 1) 4
83 Nylock Nut (M8 x 1.25) 2
84 Nylock Nut (M10 x 1.5) 4
85 Pulse Sensor Plate 4
86 Upper Pulse Sensor Housing 2
87 Lower Pulse Sensor Housing 2
88 Pulse Sensor Cap 2
89 Pulse Sensor Wire 2
90 Pedal Divider 2
91 Push Button 2
92 Press Spring 2
93 Clamp 2
94 Retaining Washer 2
95 Warning Label 1
96 Battery Warning Label 1
97 Heart Rate Transmitter 1
98 Elastic Strap 1
99 Battery Rubber Ring 1
100 Battery Cover 1
101 3V Lithium Battery (CR2032) 1
102 Socket Wrench 1
103 Allen Wrench (5mm) 1
104 Allen Wrench (6mm) 1
105 Manual 1

IMPORT ANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORT ANT : We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Plea se do not return the product. For your convenience, Sta mina has a Customer Service Department with
a toll-free number. Should a part be missing or a defective part found, please call 1 [phone]
(in the U.S.) from 7:30 A.M. to 5:00 P.M. Central T ime, Monday through Thursday a nd 8:00 A.M. to 3:00 P.M.
on Friday or fill out the fax sheet ordering form below and fax it to [phone]. Our Customer Service
Department will be able to assist you with your problem and the part will be mailed directly to your house.

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1

EXAMPLE:

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com