Stamina AeroPilates Performer XP615 Owner's Manual

Owner's

Manual

! WARNING !

Exercise can present a he alth
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

When calling for parts or
service, please specify the
following number.

55-4615

Patent Nos. D382,319

and 7,179,207.

Other Patents Applied

and Are Pending.

MADE IN CHINA

CAUTION:
We ight on this product should not exceed 300 lbs.

Product May Vary Slightly

From Pictured.

2007, 10

2007 Stamina Products, Inc.

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

www.staminaproducts.com

This Product is Produced Exclusively by

TABLE OF CONTENTS

2

Conditioning Guidelines 13
Warm-up and Cool-Down 14
Warranty 15
Product Parts Drawing 16
Parts List 17
Fax/Mail Ordering Form 19

Page Page

Safety Instruction s 2
Before You Begin 4
Hardware Identification Chart 5
Assembly Instructions 6
Operational Instructions 10
Storage 11
Mainten ance 12

Before starting any exercise or conditioning program you should con sult with your personal
physicia n to see if you require a complete physical exa m. This is e specially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

SAFETY INSTRUCTIONS

WARNING:

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

Read all warnings posted on the AeroPilates

Performer XP615.

We recommend that two people be available for assembly of this product.
Read this Owner's Ma nual a nd follow it carefully bef ore using the AeroPilates

Performer XP615.

Make sure that it is properly assembled and tightened before use.
When exercising on this product, do not exercise at an intensity that causes the product itself to
move. This could result in damage to your joints and the product.
Keep children away from the AeroPilates

Performer XP615. Do not allow children to use or play

on the AeroPilates

Performer XP615. Keep children and pets away from the AeroPilates

Performer XP615 when it is in use.

It is recommended that you place this exercise equipment on the floor mat.
Set up and operate the AeroPilates

Performer XP615 on a solid level surfa ce. Do not position the

AeroPilates

Performer XP615 on loose rugs or uneven surfaces.

Make sure that a dequate spa ce is availa ble f or a cce ss to a nd around the AeroPilates

Performer

XP615.

Inspect the AeroPilates

Performer XP615 for worn or loose components prior to use.

Tighten/repla ce any loose or worn components prior to using the AeroPilates

Performer XP615.

When folding or unfolding the AeroPilates

Performer XP615, keep all children away from the

AeroPilates

Performer XP615 and make sure your hands are clear of any folding or pinch point.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the AeroPilates

Performer XP615.

Be careful to maintain your balance while using, mounting, dismounting, or assembling the

AeroPilates

Performer XP615, loss of balance may result in a fall and serious bodily injury.
The AeroPilates

Performer XP615 should not be used by persons weighing over 300 pounds.

The AeroPilates

Performer XP615 should be used by only one person at a time.

The AeroPilates

Performer XP615 is for con sumer use only . It is not for use in public or semipublic

facilities.

WARNING:

To reduce the risk of serious injury, read the following Safety Instructions before
using th

e AeroPilates Performer XP615.

THANK YOU FOR PURCHASING THE

AeroPilates

Performer XP615

To help you get started, we have pre-assembled most of your

AeroPilates Performer XP615 at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into sha pe

and on your way to achieving a happier and healthier lifestyle.

3

Should you have any que stions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M. Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

CALL US FIRST

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

BEFORE YOU BEGIN

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Combination Wrench

Socket Wrench

Front Frame

Foam Pad

Head Re st

Pulley Assembly

Front Cover

Hand Strap

Wheels

Locking Knob

Cardio
Rebounder

Rear Cover

Tension Cords

Rear Frame

4

Grip Pad

Rope

Hand Strap

Cushion

Grip Pad

Floor Mat

Thank you for choosing the AeroPilates
Performer XP615. W e take gre at pride in producing
this quality product and hope it will provide many
hours of quality exercise to make you feel better , look
better and enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The AeroPilates
Performer XP615 provides a convenient and si mple
method to begin your assault on getting your body in
shape a nd a chieving a happier a nd healthier lifestyle.
Before reading further, please review the drawing
below and fa mili arize yoursel f with the parts that are
labeled.
Read this manual carefully before using the

AeroPilates

Performer XP615.

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your AeroPilates
Performer XP615, plea se do not return the product.
Contact us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T i me) on Friday.
If you would like to contact us online, go to our
website at www.sta mina products.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.

Carriage

Front Stand

Rear Stand

Middle Stand

Connection Bar

Front Cover

Warning

Label

5

Part No. and Description Qty

51 Washer (M8) 6

47 Nylock Nut (M8 x 1.25) 2

41 Screw, Round He ad (M5 x 0.8 x 25mm) 4

29 Rubber Foot 4

55 Locking Knob

2

28 Wheel 2

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
end of the bolts, or screws on the circles to check for the corre ct diameter. Use the small scale to check the
length of the bolts and screws.

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

mm.

in.

INCHES

MILLIMETERS

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

6 8 10 12

3/16" 5/16" 1/2"3/8"1/4"

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at :

[e-mail]

6

STEP 1

Connect the REAR STAND(61), the narrower one, to the MIDDLE STAND(60) with two CONNECTION
BARS(62), inserting the Fins on the CONNECTION BARS(62) into the gaps in the Double Flanges on the
STANDS(60, 61). Then lock the CONNECTION BARS(62) in the place by inserting the PULL PINS(65)
through the Double Flanges. Repeat to connect the FRONT STAND(59) to the MIDDLE STAND(60).

Fin

Double

Flanges

Fin

Double

Flanges

ASSEMBLY INSTRUCTIONS

7

STEP 2

Remove your AeroPilates Performer XP615 from its pa ck aging placing the product on its side, with the
LOCKING PIN(30) side upward. Remove the LOCKING PIN(30) and unf old the MAIN FRAME ASSEMBL Y

separating the half that ha s the atta ched LOCKING PIN(30). When completed, the fra me should be separated
approximately three feet at the end.

STEP 3

Attach the four RUBBER FEET(29) to the FRONT FRAME(1) and REAR FRAME(2) with ROUND HEAD
SCREWS(M5x0.8x25mm)(41). Attach the WHEELS(28) onto the FRONT FRAME(1) with WASHERS(M8)
(51) and NYLOCK NUTS(M8x1.25)(47).

STEP 4

Unf old your AeroPilates Performer XP615 to a flat position by moving the FRONT FRAME(1) away from
the platform end of the product in a clockwise position until fully extended.

STEP 5

Remove the pa per covering from the foam tape inside the FRONT COVER(7) a nd REAR COVER(8). Pla ce
the FRONT COVER(7) over the FRONT FRAME(1). Place the REAR COVER(8) over the REAR FRAME(2).
Press the covers securely in place.

NOTE:

8

ASSEMBLY INSTRUCTIONS

The securing SCREWS(M6x1x35mm)(42) for the PULLEY ASSEMBLY(26) on each side may
need to be loosened to allow the REAR COVER(8) to fit securely over the fra me. Refer to the in set
drawing A. When retightening the screws for the PULLEY ASSEMBLYS(26) do not over tighten.
The PULLEY ASSEMBLYS(26) should move freely.

STEP 6

Refer to the above illustration. Make sure that the threaded holes in
the FOOT REST(10) are facing toward the end of the AeroPilates
Performer XP615 as shown. Insert the FOOT REST(10) into the
mounting holes located in the FRONT COVER(7) and FRONT
FRAME(1). Insert the FOOT REST(10) all the way to the bottom and
lock it in place with the LOCKING KNOBS(55).

NOTE:

Y ou ca n choose to in sert the CARDIO REBOUNDER(56) into
the FRONT FRAME(1) and lock in position with the LOCKING

KNOBS(55). Refer to the inset drawing B.

A.

B.

9

ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS

(59) Front Stand

( Wider )

(61) Rear Stand

( Narrower )

SLOTS

The rubber feet of the AeroPilates Performer XP615 must fit into the FRONT STAND(59) and
the REAR STAND(61). The FRONT STAND(59) is wider than the REAR STAND(61). The Foot
Rest end of your AeroPilates

Performer XP615 will fit into the top of the FRONT ST AND(59) and

the Headrest end of your AeroPilates Performer XP615 will fit into the REAR STAND(61).

STEP 5

Insert the FOAM P AD ASSEMBLIES(21) into the holes located on the CARRIAGE(12).

STEP 10

Place the Stand on the FLOOR MAT(66) as shown in the illustration.
To prevent the CARRIAGE(12) from moving while placing the AeroPilates Performer XP615 onto its
Stand, attach one of the TENSION CORDS(15) in the slots on the FRONT FRAME(1). Refer to the inset
drawing. Place the AeroPilates

Performer XP615 onto the Stand as shown in the illustration.

NOTE:

(66) Floor Mat

LOAD ADJUSTMENT

The resistance of the CARRIAGE(12) can be adjusted by
securing the TENSION CORDS(15) in the slots located on
the FRONT FRAME(1). You can achieve various levels of
resistance by securing different numbers of the TENSION

CORDS(15) in the slots.
NOTE:

OPERATIONAL INSTRUCTIONS

10

ROPE LENGTH ADJUSTMENT

The ROPES(22) are wra pped on the HOOKS located on both
sides of the CARRIAGE(12). You can adjust the length
between the PULLEY ASSEMBLY(26) and the HAND
STRAP(24) by attaching the PLASTIC HOOKS(23) onto
different HOOKS.

Arm Function: To position the HAND STRAP(24) close
to the PULLEY ASSEMBLY(26), hook the PLASTIC

HOOK(23) onto the HOOKS which will shorten the
ROPE(22).
Leg Function: T o a chieve a full range of move ment, hook
the PLASTIC HOOK(23) of the rope onto the desired A,
B, or C hook.

1.

2.

A

B

C

HEAD REST ADJUSTMENT

The HEAD REST(19) on the CARRIAGE(12) can be
positioned at an incline by simply pivoting the SUPPORT

BRACKET underneath the HEAD REST(19).

SUPPORT
BRACKET

SLOTS

Over time your TENSION CORDS(15) will relax. To
increase resistance in the TENSION CORDS(15),
stretch and re-tie the tension cords in a more taut
position.

STORAGE

T o store the AeroPilate s Performer XP615 simply keep it in a cle an dry pla ce. The AeroPilates Performer
XP615 can be folded as illustrated for easy storage. Please follow the f ollowing process:

Remove the AeroPilates

Performer XP615 from its Stand. Refer to page 6 and revert the procedure
to disassemble the Stand for storage.
Remove the LOCKING KNOBS(55) and CAR DIO REBOUNDER(56), or the FOOT REST(10), from the
FRONT FRAME(1). Refer to illustration 1.
Remove the TENSION CORDS(15) from the slots on the FRONT FRAME(1). Move the CARRIAGE
ASSEMBLY(18) back to the REAR FRAME(2). Refer to illustration 1.
Grasp and lift the U SHAPED HANDLE(9) to fold the AeroPilates

Performer XP615. Refer to

illustration 1.

1.

2.

3.

4.

2.

WARNING:

When folding or unfolding the AeroPilates Performer XP615,
keep all children away from the AeroPilates Performer XP615
and make sure your hands are clear of any folding or pinch point.

1.

The AeroPilates Performer XP615 will be positioned as
shown in illustration 2 after fold. Insert the LOCKING PIN(30)
into the hole in the REAR FRAME(2) to lock the frames in
folded position.
NOTE: The string for the LOCKING PIN(30) is not a s long as
shown in illustration 2.

5.

11

U-SHAPED HANDLE(9)
Grasp and lift the
handle to fold.

Stand

Floor Mat

MAINTENANCE

12

The safety and integrity designed into the AeroPilates

Performer XP615 can only be maintained when

the AeroPilates

Performer XP615 is regularly exa mined for damage and wear . Spe cial attention should

be given to the following:

It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Worn or da maged components should be repla ced immediately or the AeroPilates

Performer XP615

removed from service until repair is made.
Verify that the ROPES(22) are properly installed on the PULLEY ASSEMBL YS(26).
Check the condition of the ROPES(22) and replace if they are frayed or worn.
Check the PLASTIC HOOKS(23) on the ends of the ROPES(22). Re place the ROPES(22) if PLASTIC
HOOKS(23) are damaged or deformed.
Check the TENSION CORDS(15) for wear . Repla ce the TENSION CORDS(15) that are frayed or worn.
Check the BUNGEE CORD(58) on the CARDIO REBOUNDER(56) for wear. Replace the CARDIO
REBOUNDER(56) if the BUNGEE CORD(58) is frayed or worn.
Check the pulleys for excessive wear. Replace worn pulleys.
Check the GRIP PADS(25) for damage. Re place damaged parts.
Check the FOAM SLEEVE(11) and FOAM PADS(21) and replace if da maged or worn.
Check the STOP PLATES(31, 33) for looseness or damage and replace any damaged parts.
Check the CUSHION(18) and replace if it is damaged or worn.
Check and clean the rollers and the rolling surfaces on the rail. Clean by wiping with a dry cloth.
Only Stamina Products supplied components shall be used to maintain/repair the AeroPilates

Performer XP615.

Keep your AeroPilates

Performer XP615 clean by wiping with an absorbent cloth after use.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

13

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually, too, by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone f or a few minutes; however, your aerobic
ca pa city will improve over the next six to e ight weeks. It is i mporta nt to pa ce yourself while you exercise so
you don’t tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingers on your wrist and take a six second heartbeat count. Multiply the
results by ten to find your heart rate. For exa mple, if your six second he artbeat
count is 14, your heart rate is 140 beats per minute. A six second count is
used because your heart rate will drop rapidly when you stop exercising.
Adjust the intensity of your exercise until your heart rate is at the proper level.

wrist pulse

Have your doctor review your training and diet programs.
Begin your training progra m slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower inten sity and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.

Target Heart Rate Zone Estimated by Age*

Remember to follow these e ssentials:

To determine if you are working out at the correct intensity, use a he art rate monitor or use the table below .
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting a n exercise program, work out at the low end of your target heart
rate zone. As your a erobic ca pacity i mproves, gradually increa se the intensity of your workout by incre a sing
your heart rate.

For cardiorespiratory training benefits, the American College of Sports Medicine re commends working
out within a heart rate range of 55% to 90% of maxi mum he art rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate

*

20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute

200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

14

WARM-UP and COOL-DOWN

Warm-up The purpose of warming up is to prepare your body f or exercise and to mini mize injuries. W arm

up for two to five minutes before strength-training or aerobic exercising. Perform activities that raise your
heart rate and warm the working muscle s. Activitie s may include brisk walking, jogging, jumping ja cks, jump
rope, and running in place

Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength

or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevated temperature, which greatly reduces the risk of in jury . Stretches should be held for 15 to 30 seconds.
Do not bounce.

Suggested Stretching Exercise s

Remember always to check with your physician before starting any exercise program.

Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state

at the end of ea ch exercise se ssion. A proper cool-down slowly lowers your heart rate a nd allows blood to
return to the heart. Y our cool-down should include the stretche s listed above a nd should be completed after
each strength-training session.

Lower Body Stretch

Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessen, try a lower
position gradually.

Floor Stretch

While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder­width a part and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the floor,
have legs apart one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and five years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilities, and other public or se mipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, fa mily, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Stamin a Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 [phone]. If the defect is covered under this limited
warranty , you will be requested to return the product or part to us f or free repair or repla cement at our option.

NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE T O YOU. In the event that the purchaser makes a ny clai m under this

limited warranty or a ny implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date and place of purchase.

Stamin a Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or express warranty given by Stamina Products, Inc. This warra nty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers and li mitations of a nd on implied warranties a nd
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

15

WARRANTY

LIMITED WARRANTY

MODEL 55-4615

PRODUCT PARTS DRAWING

16

FRONT

BACK

PARTS LIST

DIAGRAM# PART NAME QTY

1 Front Frame 1
2 Rear Frame 1
3 Front Left Side Rail 1
4 Front Right Side Rail 1
5 Rear Left Side Rail 1
6 Rear Right Side Rail 1
7 Front Cover 1
8 Rear Cover 1
9 U Shaped Handle 1
10 Foot Rest 1
11 Foam Sleeve 1
12 Carriage 1
13 Roller 4
14 Roller Spacer 4
15 Tension Cord 4
16 Support Bushing 4
17 Stop Bushing 4
18 Cushion 1
19 Head Rest 1
20 Foam Pad T ube 2
21 Foam Pad 2
22 Rope 2
23 Pla stic Hook 2
24 Hand Strap 2
25 Grip Pad 2
26 Pulley Assembly 2
27 Pulley Spa cer 2
28 Wheel 2
29 Rubber Foot 4
30 Locking Pin 1
31 Stop Plate 2
32 Stop Pad 2
33 Small Stop Plate 2
34 Small Stop Pad 2
35 Round Plug (25mm) 4
36 Shaft Bolt, Socket Head (M8 x 1.25 x 20mm) 2
37 Bolt, Socket Head/w hole (M8 x 1.25 x 20mm) 1
38 Bolt, Socket Head (M8 x 1.25 x 20mm) 7
39 Bolt, Round Head (M8 x 1.25 x 25mm) 4
40 Screw , Round He ad (M3.5 x 11mm) 12
41 Screw , Round Head (M5 x 0.8 x 25mm) 4
42 Screw , Round Head (M6 x 1 x 35mm) 2
43 Screw , Flat Head (M5 x 0.8 x 25mm) 3
44 Acorn Nut (M5 x 0.8) 4
45 Nylock Nut (M5 x 0.8) 7
46 Nylock Nut (M6 x 1) 2
47 Nylock Nut (M8 x 1.25) 14
48 Nut (M8 x 1.25) 4

17

PARTS LIST

DIAGRAM# PART NAME QTY

18

49 Washer (M5) 7
50 Washer (M6) 2
51 Washer (M8) 20
52 Washer (M10) 4
53 Lock Washer (M8) 4
54 Warning label 1
55 Locking Knob 2
56 Cardio Rebounder 1
57 Rebounder Mat 1
58 Bungee Cord 1
59 Front Stand 1
60 Middle Sta nd 1
61 Rear Stand 1
62 Connection Bar 4
63 Endcap 6
64 Large Washer (60mm dia meter) 6
65 Pull Pin 8
66 Floor Mat 1
67 Combination Wrench 1
68 Socket Wrench 1
69 Manual 1
70 DVD, Basic Reformer Workout 1
71 DVD, AeroPilates Performer Level One Workout 1
72 DVD, AeroPilates Performer Cardio Workout 1
73 Workout Chart 1

IMPORT ANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORT ANT : We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Plea se do not return the product. For your convenience, Sta mina has a Customer Service Department with
a toll-free number. Should a part be missing or a defective part found, please call 1 [phone]
(in the U.S.) from 7:30 A.M. to 5:00 P.M. Central T ime, Monday through Thursday a nd 8:00 A.M. to 3:00 P.M.
on Friday or fill out the fax sheet ordering form below and fax it to [phone]. Our Customer Service
Department will be able to assist you with your problem and the part will be mailed directly to your house.

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1

EXAMPLE:

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com