Stamina 1750 Power Tower System, 50-1750 Owner's Manual

When calling for parts or

service, please specify

the following number

:

Model#: 50-1750

CAUTION:
Weight on this product should not exceed 250 lbs.

Owner's

Manual

This Product is Produced Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

Product May Vary Slightly From Pictured.

STAMINA PRODUCTS

MADE IN CHINA

©

2010 Stamina Products, Inc.

2010, 09

Exercise can present a
h e a l t h r i sk . Co n su l t a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
dis c o n t i n ue use of this
equipment. Serious bodily
in j u r y c a n occ u r if th is
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all in str uct ion s a re not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

!

WARNING

Meijer.com

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Operational Instructions ...........................

14

Storage ....................................................... 15

Maintenance ............................................... 15

Conditioning Guidelines ........................... 16

Warm-Up and Cool-Down ......................... 17

Workout Instructions ................................ 18

Product Parts Drawing .............................. 20

Parts List .................................................... 21

Warranty ..................................................... 22

Fax/Mail Ordering Form ............................ 23

SAFETY INSTRUCTIONS

2

1. Read all warnings posted on the 1750 Power Tower.

2. The 1750 Power Tower should only be used after a thorough review of the Owner’s Manual.

3. We recommend that two people be available for assembly of this product.

4. Keep children away from the 1750 Power Tower. Do not allow children to use or play on the 1750
Power Tower. Keep children and pets away from the 1750 Power Tower when it is in use.

5. It is recommended that you place this exercise equipment on an equipment mat.

6. Set up and operate the 1750 Power Tower on a solid level surface. Do not position the 1750
Power Tower on loose rugs or uneven surfaces.

7. Make sure that adequate space is available for access to and around the 1750 Power Tower.

8. Before using, inspect the 1750 Power Tower for worn or loose components, and securely tighten
or replace any worn or loose components prior to use.

9. C o nsult a p h y s i c i a n prior to co m m encing an ex e r c ise progr a m an d follow h i s / h e r

recommendations in developing your tness program. If at any time during exercise you feel faint,

dizzy, or experience pain, stop and consult your physician.

10. Follow your physician’s recommendations in developing your own personal tness program.

11. Always choose the workout which best ts your physical strength and exibility level. Know your

limits and train within them. Always use common sense when exercising.

12. Do not wear loose or dangling clothing while using the 1750 Power Tower.

13. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or

cross training shoes that t well, provide foot support, and feature non-skid rubber soles.

14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the 1750
Power Tower, loss of balance may result in a fall and serious bodily injury.

15. The 1750 Power Tower should not be used by persons weighing over 250 pounds.

16. The 1750 Power Tower should be used by only one person at a time.

17. The 1750 Power Tower is for consumer use only. It is not for use in public or semipublic facilities.

!

WARNING

This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is

especially important if you are over the age of 35, have never exercised before,

are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in bodily injury and property damage.
To reduce the risk of serious injury, read the following Safety Instructions
before using the 1750 Power Tower.

!

WARNING

!

CAUTION

OPERATIONAL INSTRUCTIONS

Meijer.com

THANK YOU FOR PURCHASING THE

1750 Power Tower

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

3

Call Us First

www.staminaproducts.com

1 [phone]

Customer Service

Your 1750 Power Tower does require assembly.

Please follow the assembly steps set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

Meijer.com

Extend Arm Support

Rear Support

Brace Support

Pull-Up Bar

Connecting Brace

Back Cushion

Upper Upright

Support Bar

Arm Cushion

Base Frame

Endcap

Bench Extend Arm

Extend Arm Support

Caution Label

Bench Cushion

Extend Arm

Thank you for choosing the 1750 Power Tower.
We tak e great pri de i n pr oducing thi s qu alit y
product and hope it will provide many hours of
qu ality exercise to make y ou feel b etter, loo k
better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The 1750 Power Tower
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.

Befor e r e ading fu r t h er, p lease rev i e w the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the

1750 Power Tower.

Although Stamina constructs its products with

the nest materials and uses the highest standards

BEFORE YOU BEGIN

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your 1750 Power Tower,
please do not retu rn the prod uct. Con tact us
FIRST!

If a par t is missing o r defective, please call

us toll free at 1-800-375-7520 (in the U.S.). Our

Customer Service Staff is available to assist you

from 7:30 A.M. to 5:00 P.M. (Central Time) Monday

th rou gh Thursday and 8: 00 A.M. to 3:00 P.M.

(Central Time) on Friday.

If you would like to contact us online, go to our
website at www.staminaproducts.com and access
the Customer Service section.

Be sure to have the name and model number of
the product available when you contact us.

4

Foam Support Bar

Endcap

Cross Bar

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench (2 pieces)

Meijer.com

5

Label is larger than actual size

This chart is provided to help identify the warning, caution, and notice labels on the 1750 Power
Tower. Please take a moment to familiarize yourself with all of the warning, caution, and notice

labels.

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

CAUTION LABEL(39)C1

Meijer.com

37 Washer (M8) 24
38 Washer (M10) 56
58 Washer (M6) 6

Part Number and Description Qty

27 Bolt, Hex Head (M8 x 1.25 x 20mm) 2
30 Bolt, Hex Head (M10 x 1.5 x 15mm) 8
55 Bolt, Hex Head (M6 x 1 x 15mm) 6

28 Bolt, Hex Head (M8 x 1.25 x 65mm) 4
29 Bolt, Hex Head (M8 x 1.25 x 70mm) 9

36 Arc Washer (M10) 2

This chart is provided to help identify the hardware used in the assembly process. Place the washers or

the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to

check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

HARDWARE IDENTIFICATION CHART

6

mm.

in.

INCHES

MILLIMETERS

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

6 8 10 12

3/16" 1/4" 5/16" 3/8" 1/2"

32 Bolt, Hex Head (M10 x 1.5 x 65mm) 11
33 Bolt, Hex Head (M10 x 1.5 x 70mm) 8

31 Bolt, Hex Head (M10 x 1.5 x 45mm) 2

34 Nylock Nut (M8 x 1.25) 9
35 Nylock Nut (M10 x 1.5) 24

56 Bolt, Hex Head (M10 x 1.5 x 115mm) 3
57 Bolt, Hex Head (M10 x 1.5 x 140mm) 2

Meijer.com

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the
packing materials until assembly is completed. Read each step carefully before beginning. If you

are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at

[e-mail].

ASSEMBLY INSTRUCTIONS

NOTE: DO NOT SECURELY TIGHTEN ALL BOLTS UNTIL STEP 8.

STEP 1

Con nect t he t w o BAS E FRA MES(1 ) wit h the CROS S BAR ( 2) an d sec ure w ith H EX BO LT S
(M10x1.5x65mm)(32), WASHERS(M10)(38), and NYLOCK NUTS(M10x1.5)(35).

STEP 2

Insert the LOWER UPRIGHTS(3) into the BASE FRAMES(1) on both sides and secure with HEX
BOLTS(M10x1.5x15mm)(30) and WASHERS(M10)(38). Connect the two LOWER UPRIGHTS(3) with

the FOAM SUPPORT BAR(5) and secure with HEX BOLTS(M10x1.5x65mm)(32), WASHERS(M10)(38),
and NYLOCK NUTS(M10x1.5)(35).

7

Meijer.com

ASSEMBLY INSTRUCTIONS

STEP 3

Insert the two SUPPORT BARS(4) between the BASE FRAMES(1) and the LOWER UPRIGHTS(3),
then secure at top and bottom to the BASE FRAMES(1) and the LOWER UPRIGHTS(3) with HEX
BOLTS(M8x1.25x70mm)(29), WASHERS(M8)(37), and NYLOCK NUTS(M8x1.25)(34).

STEP 4

Insert the two UPPER UPRIGHTS(11) into the LOWER UPRIGHTS(3) and secure with HEX BOLTS
(M10x1.5x65mm)(32), WASHERS(M10)(38), and NYLOCK NUTS(M10x1.5)(35).

STEP 5

Attach the PULL-UP BAR(12) to both the UPPER UPRIGHTS(11) with HEX BOLTS(M10x1.5x45mm)(31)
and ARC WASHERS(M10)(36).

8

Meijer.com

ASSEMBLY INSTRUCTIONS

9

STEP 6

Co nne ct the two EX TEND ARM S(8) w ith the CONNECTING BRACE(10) and s ecu re with the
MOUNTING BRACKETS(6), HEX BOLTS(M10x1.5x70mm)(33), WASHERS(M10)(38), and NYLOCK
NUTS(M10x1.5)(35).

STEP 7

Attach the EXTEND ARM ASSEMBLY(8) to the LOWER UPRIGHTS(3) and the UPPER UPRIGHTS(11)
with the LARGE MOUNTING BRACKETS(7), HEX BOLTS(M10x1.5x70mm)(33), WASHERS(M10)(38),
and NYLOCK NUTS(M10x1.5)(35).

STEP 8

Insert the two EXTEND ARM SUPPORTS(9) between the EXTEND ARMS(8) and the LOWER
UPRIGHTS(3), then secure with HEX BOLTS(M8x1.25x70mm)(29), WASHERS(M8)(37), and NYLOCK
NUTS(M8x1.25)(34). SECURELY TIGHTEN ALL OF THE BOLTS FROM STEP 1 THROUGH STEP 8.

Meijer.com

ASSEMBLY INSTRUCTIONS

STEP 9

Attach the ARM CUSHIONS(13) to the EXTEND ARMS(8) with HEX BOLTS(M8x1.25x65mm)(28) and
WASHERS(M8)(37).

STEP 10

Attach the BACK CUSHION(14) to the CONNECTING BRACE(10) with HEX BOLTS(M8x1.25x20mm)
(27) and WASHERS(M8)(37).

10

Meijer.com

ASSEMBLY INSTRUCTIONS

STEP 11

Atta c h the B ENCH E X TEND ARMS( 4 2) to t he FOA M SUPP O R T BAR ( 5) wit h HEX B O LT S
(M10x1.5x115mm)(56), WASHERS(M10)(38), and NYLOCK NUTS(M10)(35). Do not tighten the bolts

until STEP 12.

STEP 12

Attach the REAR SUPPORT(40) to the BENCH EXTEND ARMS(42) with HEX BOLT(M10x1.5x115mm)
(5 6 ) , WA S H ERS( M 1 0 )(38 ) , a nd N Y L O CK N U T ( M 10)( 3 5 ) . Do no t ov e r t ight e n the HE X
BOLT(M10x1.5x115mm)(56) as the REAR SUPPORT(40) must be able to pivot smoothly after HEX
BOLT(M10x1.5x115mm)(56) is tightened. Insert the LONG BALL PIN(49) through the BENCH EXTEND
ARMS(42) and the REAR SUPPORT(40) to lock the REAR SUPPORT(40) in position. Tighten the two
HEX BOLTS(M10x1.5x115mm)(56) for STEP 11.

11

Meijer.com

ASSEMBLY INSTRUCTIONS

12

STEP 13:

Refer to the detail view 1. Attach the SUPPORT LEG(41) to the REAR SUPPORT(40) with

HEX BOLT (M8x1.25x70mm)(29), WASHERS(M8)(37), and NYLOCK NUT(M8)(34).

NOTE:

Do not over tighten HEX BOLTS(32, 57) as the BRACE TUBES(43, 44), BRACE SUPPORT(45),
and CONNECTING BRACKET(46) must be able to pivot smoothly after HEX BOLTS(32, 57) are
tightened.

STEP 14:

Attach the LEFT and RIGHT BRACE TUBES(43, 44) to the REAR SUPPORT(40) with
HEX BOLT(M10x1.5x140mm)(57), WASHERS(M10)(38), and NYLOCK NUT(M10)(35). Attach
the BRACE SUPPORT(45) between th e LEFT and RIGHT BRA CE TUBE S(4 3, 44) wit h HEX
BOLT(M10x1.5x140mm)(57), WASHERS(M10)(38), and NYLOCK NUT(M10)(35).

STEP 15:

Attach the C ONNECTING BRACKE T(4 6) to t he BRACE SUPP ORT (45 ) with HEX
BOLT ( M10x 1 .5x6 5 mm)( 3 2), WAS HERS( M10)( 38), a nd N Y LOCK NUT( M 10)(3 5). P lace the
CONNECTING BRACKET(46) on the REAR SUPPORT(40) and lock in place by inserting the BALL
PIN(48) into one of the adjustment holes.

NOTE: There are three adjustment holes on the REAR SUPPORT(40) for adjusting the angle of the

Bench.

1.

Meijer.com

ASSEMBLY INSTRUCTIONS

13

STEP 16

At tach the B ENC H CUSHION(47) to the LEFT and RIGHT BRA CE TUBES(43, 44) wi th HEX
BOLTS(M6x1x15mm)(55) and WASHERS(M6)(58).

Meijer.com

SWITCH THE BENCH

The Bench is preset under the PULL-UP BAR(12).
You will need to fold and switch the Bench to other

si de when yo u want to do the pull-up w ork out .

Follow the process below to switch the Bench:

1. Adjust the BENCH CUSHION(47) to the lowest
decline angle and secure with the BALL PIN(48).

2. Unloc k t h e R E A R SUPPORT(40) from t h e
BENCH EXTEND ARMS(42) by pulling out the
LONG BALL PIN(49). Store the LONG BALL
PIN(4 9 ) by slid i n g it ba c k into the B E NCH
EXTEND ARMS(42). The LONG BALL PIN(49)

must not pass through the REAR SUPPORT(40)
as shown in illustration A.

OPERATIONAL INSTRUCTIONS

14

A.

B. C. D.

3. Refer to illustration B. lift the Bench from the stabilizer of the REAR SUPPORT(40). When the BENCH
EXTEND ARMS(42) near the vertical position, as shown in illustration C, push down the stabilizer

slightly and continue to fold the Bench to other side. The Bench should look as shown in illustration D
after folded.

Slightly push
down here.

Meijer.com

1. To store the 1750 Power Tower, simply keep it in a clean dry place.

2. Three people are required to move the 1750 Power Tower. Use two people to lift from both EXTEND

ARMS(8). Use one person to support, but not lift, the Bench while moving.

STORAGE

15

The safety and integrity designed into the 1750 Power Tower can only be maintained when the 1750
Power Tower is regularly examined for damage and wear. Special attention should be given to the

following:

1. Verify that the CAUTION LABEL(39) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement CAUTION LABEL(39) if it is missing or damaged.

2. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Securely tighten loose nuts and bolts.

4. Worn or damaged components shall be replaced immediately or the 1750 Power Tower removed
from service until repair is made.

5. Only Stamina Products supplied components shall be used to maintain/repair the 1750 Power Tower.

6. Keep your 1750 Power Tower clean by wiping it off with an absorbent cloth after use.

MAINTENANCE

Meijer.com

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or

three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second

heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.

wrist pulse

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.

Take your pulse periodically during your workout and strive to stay within a range of 60% (lower

intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically t.

If you feel dizzy or lightheaded you should slow down or stop exercising.

To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.

CONDITIONING GUIDELINES

Target Heart Rate Zone Estimated by Age*

* For cardiorespiratory training benefits, the American College of Sports Medicine recommends

working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the

maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate

20 years

25 years

30 years

35 years

40 years

45 years

50 years

55 years

60 years

65 years

70 years

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute

107-175 beats per minute

105-171 beats per minute

102-166 beats per minute

99-162 beats per minute

97-157 beats per minute

94-153 beats per minute

91-148 beats per minute

88-144 beats per minute

85-139 beats per minute

83-135 beats per minute

200 beats per minute

195 beats per minute

190 beats per minute

185 beats per minute

180 beats per minute

175 beats per minute

170 beats per minute

165 beats per minute

160 beats per minute

155 beats per minute

150 beats per minute

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

16

Meijer.com

WARM-UP and COOL-DOWN

Warm-Up

The purpose of warming up is to prepare your body for exercise and to minimize injuries.

Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that

raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place

Stretching

Stretching while your muscles are warm after a proper warm-up and again after your

strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.

Suggested Stretching Exercises

Remember to always check with your physician before starting any exercise program.

Cool-Down

The purpose of cooling down is to return the body to its normal, or near normal, resting

state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be

completed after each strength training session.

Lower Body Stretch

Place feet shoulder-width

apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.

DO NOT BOUNCE!

When the pull on the back of
the legs lessens, gradually
try a lower position.

Floor Stretch

While sitting on the oor,

open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.

DO NOT BOUNCE!

Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder-

width apart and lean forward

as illustrated. Using the

arms, gently pull the upper
body towards the right leg.
Let the head hang down.

DO NOT BOUNCE!

Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the oor,

have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

17

Meijer.com

18

WORKOUT INSTRUCTIONS

Dips:

A variation can be to lower yourself from the start position to only halfway down.

Push-ups:

A variation can be to lower yourself from the start position to only halfway down.

Start Finish

Start Finish

Start Finish

Lat Pull-ups:

Variations can include using a medium or narrow grip.

Meijer.com

19

WORKOUT INSTRUCTIONS

Vertical Knee Raise:

Variations can include alternately raising each leg or bringing the legs up in a twisting motion.

Start Finish

Sit-ups:

A variation can be to twist your torso as you sit up.

Meijer.com

PRODUCT PARTS DRAWING

20

BACK

FRONT

Meijer.com

PART# PART NAME QTY

1 Base Frame 2
2 Cross Bar 1

3 Lower Upright 2

4 Support Bar 2
5 Foam Support Bar 1
6 Mounting Bracket 2
7 Large Mounting Bracket 2
8 Extend Arm 2
9 Extend Arm Support 2
10 Connecting Brace 1

11 Upper Upright 2
12 Pull-Up Bar 1

13 Arm Cushion 2
14 Back Cushion 1

15 Foam Grip (ø30 x ø38 x 165mm) 4
16 Foam Tube (ø22 x ø32 x 140mm) 2
17 Foam Tube (ø22 x ø32 x 265mm) 2
18 Foam Tube (ø22 x ø32 x 445mm) 1
19 Foam Pad (ø26 x ø48 x 150mm) 2

20 Foam Pad Sleeve 2
21 Support Bar Tread 2

22 Connective Cap (50mm x 50mm) 2
23 Hollow Cap (50mm x 50mm) 2
24 Round Plug (25.4mm) 4
25 Round Plug (31.8mm) 4
26 Endcap (50mm x 50mm) 4
27 Bolt, Hex Head (M8 x 1.25 x 20mm) 2
28 Bolt, Hex Head (M8 x 1.25 x 65mm) 4
29 Bolt, Hex Head (M8 x 1.25 x 70mm) 9
30 Bolt, Hex Head (M10 x 1.5 x 15mm) 8
31 Bolt, Hex Head (M10 x 1.5 x 45mm) 2
32 Bolt, Hex Head (M10 x 1.5 x 65mm) 11
33 Bolt, Hex Head (M10 x 1.5 x 70mm) 8
34 Nylock Nut (M8 x 1.25) 9
35 Nylock Nut (M10 x 1.5) 24
36 Arc Washer (M10) 2
37 Washer (M8) 24
38 Washer (M10) 56

39 Caution Label 1
40 Rear Support 1
41 Support Leg 1
42 Bench Extend Arm 2
43 Left Brace Tube 1
44 Right Brace Tube 1
45 Brace Support 1
46 Connecting Bracket 1
47 Bench Cushion 1

48 Ball Pin (ø10 x 65mm) 1
49 Long Ball Pin (ø10 x 110mm) 1

50 EVA Pad 2

51 Endcap (50mm) 2
52 Square Plug (20mm x 20mm) 4
53 Square Plug (50mm x 50mm) 3
54 Retangular Plug (25mm x 50mm) 4
55 Bolt, Hex Head (M6 x 1 x 15mm) 6
56 Bolt, Hex Head (M10 x 1.5 x 115mm) 3
57 Bolt, Hex Head (M10 x 1.5 x 140mm) 2
58 Washer (M6) 6

59 Wrench 2
60 Manual 1

PARTS LIST

21

Meijer.com

LIMITED WARRANTY

WARRANTY

MODEL 50-1750

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship

under normal use, service and proper operation for a period of 90 days on the parts and ve years on

the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL
NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health

clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the

product's use is in furtherance of a prot making enterprise, and all other use which is not for personal,

family, or household purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE

DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR

BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER

DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state to

state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

22

Meijer.com

IMPORTANT : Before lling out the form below make sure you have the correct information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

IMPORTANT : We must have your phone number to process the order!

Please do not return the product. For your convenience, Stamina's Customer Service Department can be

reached by email at [e-mail] or toll free at 1-800-375-7520 (in the U.S.).

Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central

Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or ll out the fax sheet ordering
form below and fax it to [phone]. Our Customer Service Department will be able to assist you with

your problem and the part will be mailed directly to your house.

Mr./Ms:

Address: Apt. #:

City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )

Date Purchased:

Model #:

Purchased From:

 

PART # DESCRIPTION QUANTITY

 

1 Rear Unit Assembly 1

EXAMPLE:

FAX/MAIL ORDERING FORM

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

Meijer.com