Die Konformität zu Normen und Bestimmungen kann den entsprechenden Zertifikaten
und der EG-Konformitätserklärung entnommen werden. Diese Dokumente können auf
unserer Homepage www.stahl-ex.com abgerufen werden.
R. STAHL Schaltgeräte GmbH
Am Bahnhof 30
74638 Waldenburg
Germany
T
F
+49 7942 943-0
+49 7942 943-4333
www.stahl-ex.com
2
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
218095/FX1560300010
2013-08-27·BA00·III·de·02
2Verwendete Symbole
Sicherheitshinweise
Nichtbeachtung kann zu Sachschäden, schweren Verletzungen oder zum
Tod führen.
Die Sicherheitshinweise dieser Betriebsanleitung und auf dem Gerät sind
unbedingt zu beachten!
Verwendete Symbole
DE
DE
DE
DE
DE
DE
Warnzeichen
Gefahr durch explosionsfähige Atmosphäre!
Warnzeichen
Gefahr durch spannungsführende Teile!
Hinweis
Diese Grafik kennzeichnet wichtige Zusatzinformationen, Tipps und
Empfehlungen.
3Allgemeine Sicherheitshinweise
3.1Aufbewahrung der Anleitung
Die Betriebsanleitung ist sorgfältig zu lesen und am Geräteeinbauort aufzubewahren. Für
den ordnungsgemäßen Betrieb sind alle der Lieferung beigelegten Dokumente sowie die
Betriebsanleitungen der anzuschließenden Geräte zu beachten.
Geräte nur für den zugelassenen Einsatzzweck verwenden!
Für Schäden, die durch fehlerhaften oder unzulässigen Einsatz sowie durch
Nichtbeachtung dieser Betriebsanleitung entstehen, übernehmen wir keine
Haftung.
Das Gerät darf nur im unbeschädigten und sauberen Zustand betrieben
werden.
WARNUNG
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
WARNUNG
Kein unbefugtes Arbeiten am Gerät!
Installation, Instandhaltung, Wartung und Störbeseitigung dürfen nur von dazu
befugtem und entsprechend geschultem Personal durchgeführt werden.
Beachten Sie Folgendes bei Installation und Betrieb:
-Beschädigungen können den Explosionsschutz aufheben
-Nationale und örtliche Sicherheitsvorschriften
-Nationale und örtliche Unfallverhütungsvorschriften
-Nationale und örtliche Montage- und Errichtungsvorschriften
-Allgemein anerkannte Regeln der Technik
-Sicherheitshinweise dieser Betriebsanleitung
-Kennwerte und Bemessungsbetriebsbedingungen der Typ- und Datenschilder
-Zusätzliche Hinweisschilder auf dem Gerät
218095/FX1560300010
2013-08-27·BA00·III·de·02
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
3
DE
IIBIECEx BAS 13.0005X
IICIECEx BAS 13.0003X
IIB, IICIEC 60079-0: 2011 / IEC 60079-1: 2007-04 / IEC 60079-31: 2008
IIBEx d IIB T* Gb (Ta = -60 … +** °C)
Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IICEx d IIC T* Gb (Ta = -60 … +** °C)
Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IIBBaseefa13ATEX0007X
IICBaseefa13ATEX0006
IIB, IICEN 60079-0: 2012 / EN 60079-1: 2007 / EN 60079-31: 2009
IIBEII 2 G Ex d IIB T* Gb (Ta = -60 … +** °C)
EII 2 D Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IICEII 2 G Ex d IIC T* Gb (Ta = -60 … +** °C)
EII 2 D Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
DE
DE
DE
DE
DE
DE
DE
DE
Bestimmungsgemäße Verwendung
3.2Umbauten und Änderungen
WARNUNG
Umbauten und Änderungen am Gerät sind nicht zulässig.
Für Schäden, die aus Umbauten und Änderungen entstehen, übernehmen wir
weder Haftung noch Gewährleistungsverpflichtungen.
3.3Sonderausführungen
Sonderausführungen können bei zusätzlichen/abweichenden Bestelloptionen von den
hier beschriebenen Darstellungen abweichen.
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
4Bestimmungsgemäße Verwendung
Das explosionsgeschützte optische Signalgerät der Reihe FX 15 liefert ein optisches
Blinksignal, das zur Alarmierung, Warnung oder als Hinweis auf ein Ereignis vorgesehen
ist. Es ist für den Einsatz in explosiongsgefährdeter bzw. rauer Umgebung vorgesehen.
In explosionsgefährdeten Bereichen besitzen die Geräte Explosionsschutz für
ATEX/IECEx Zonen 1 + 2 bei Gas und 21 + 22 bei Staub. Das Gerät ist für die Gasgruppe
IIB bzw. IIC und Staubgruppe IIIC geeignet.
5Technische Daten
Explosionsschutz
Global (IECEx)
Gas und Staub
Europa (ATEX)
Gas und Staub
* Temperaturklasse in der Tabelle
4
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
218095/FX1560300010
2013-08-27·BA00·III·de·02
Explosionsschutz
Strom und
Spannung
TemperaturklasseMax. Oberflächen-
temperatur
Umgebungstemperaturbereich
5 J
24 V DC
T6T73 °C-60 … +40 °C
T5T88 °C-60 … +55 °C
T4T103 °C-60 … +70 °C
5 J
48 V DC
T6T73 °C-60 … +40 °C
T5T88 °C-60 … +55 °C
T4T103 °C-60 … +70 °C
5 J
115 V AC
T5T83 °C-60 … +40 °C
T4T113 °C-60 … +55 °C
5 J
230 V AC
T6T75 °C-60 … +40 °C
T5T90 °C-60 … +55 °C
T4T105 °C-60 … +70 °C
24 V DC300 mA
48 V DC185 mA
115 V AC140 mA
230 V AC75 mA
24 V DC500 mA
48 V DC250 mA
115 V AC900 mA
230 V AC100 mA
Produktvariantentabelle
Technische Daten
Produktgewicht2,4 kg
Elektrische Daten
Bemessungsbetriebsspannung
Bemessungsbetriebsstrom
24 V DC, 48 V DC, 115 V AC und 230 V AC
Betriebsparameter +/-10 %
Transport und Lagerung
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
Einschaltstrom
Mechanische Daten
Material
GehäuseGRP
KalottenabdeckungPolycarbonat
SchutzgitterEdelstahl
SchutzartIP66 & IP67 IEC 60529
Lichttechnische Daten
Lichtstärke effektiv49 cd Klarlinse
Lichtmenge9,96 cds
Blitzenergie5 J
Blitzfrequenz1 pro Sekunde
Betriebstemperaturbereich24 & 48 V DC -50 ... +70 °C
115 V AC -55 ... +55 °C
230 V AC -55 ... +70 °C
DE
DE
DE
DE
DE
DE
DE
DE
6Transport und Lagerung
218095/FX1560300010
2013-08-27·BA00·III·de·02
-Transport und Lagerung sind nur in Originalverpackung gestattet.
-Die Geräte sind trocken und erschütterungsfrei zu lagern.
-Verpackungsmaterial erst nach beendeter Installation entsorgen.
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
5
DE
148 mm / 5.83 "
137 mm / 5.39 "
239 mm / 9.41 "
87 mm / 3.43 "
105 mm / 4.13 "
78 mm / 3.07 "
75 mm / 2.95 "
265 mm / 10.43 "
ø 9 mm
ø 0.35 "
245 mm / 9.65 "
1646 6mm / .4 "
ø 8,50 mm / ø 0.33 "
152 mm / 5.98 "
78 mm / 3.07 "
180 mm / 7.09 "
253 mm / 9.96 "
152 mm / 5.98 "
78 mm / 3.07 "
180 mm / 7.09 "
28 mm
1.10 "
25 mm
0.98 "
ø 8,50 mm
ø 0.33 "
87 mm / 3.43 "
20 mm
0.79 "
75 mm / 2.95 "
ø 9 mm
ø 0.35 "
105 mm / 4.13 "
DE
Installation
7Installation
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
7.1Maßangaben / Befestigungsmaße
Maßzeichnungen (alle Maße in mm) - Änderungen vorbehalten
DE
DE
DE
DE
DE
DE
DE
15739E0015738E0015737E00
Abmessungen LeuchtsignalLeuchtsignal mit 'L'-WinkelLeuchtsignal mit Griffrückenwinkel
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
218095/FX1560300010
2013-08-27·BA00·III·de·02
7.2Einbaubedingungen
Gefahr durch Stromschlag!
Vor dem Öffnen des Gerätes Spannungsversorgung unterbrechen.
WARNUNG
Installation
DE
DE
DE
DE
DE
WARNUNG
Bei beschädigten oder nicht korrekt installierten Komponenten ist der
Explosionsschutz nicht mehr gewährleistet!
Das Gerät darf nur in unabeschädigtem Zustand betrieben werden.
Bei beschädigtem Gewinde ist das Gerät sofort auszutauschen.
Bei Handhabung des Geräts und der Bauelemente ist mit höchster Sorgfalt
vorzugehen.
Mit besonderer Sorgfalt ist beim Anschluss an die Leiterplatte beim Einbau
vorzugehen.
Freiliegende Spaltoberflächen sind zu schützen und dürfen nicht mit Staub
oder Schmutz in Berührung kommen oder gegen einen Gegenstand
stoßen.
Die Endflansche müssen gerade eingebaut werden unter Vermeidung
jeglicher Kraftanwendung.
Der Flansch darf nicht mit einem Hammer bearbeitet oder mit einem
Metallwerkzeug gehebelt oder an den Befestigungsschrauben nach unten
gezogen werden.
Bei entsprechender Sorgfalt und Geduld werden Sie feststellen,
dass der sich der Flansch leicht in das Gehäuse einsetzen lässt.
Das Gerät darf nur in sauberer und trockener Betriebsumgebung
eingebaut werden.
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
Folgendes ist zu prüfen:
Besitzen Sie ein ordnungsgemäßes Gerät, das die Systemvorgaben
erfüllt?
Sind die Gasgruppe und der Temperaturbereich des Produkts für die
bestimmungsgemäße Anwendung geeignet?
Liegt die richtige Versorgungsspannung vor?
Besitzt die Blitzlampe die richtige Farbe?
Ist ein geeigneter Einbauort vorhanden?
7.3Montage und Gebrauchslage
Nicht korrekt installierte Komponenten!
Bei nicht korrekt installierten Komponenten ist der Explosionsschutz nicht
mehr gewährleistet.
Bei Verwendung von Aderendhülsen müssen diese unbedingt gasdicht mit
geeignetem Werkzeug angebracht werden.
-Wählen Sie bezüglich des vom FX15 abzudeckenden Bereichs einen geeigneten Ort
aus.
-Die Oberfläche muss im Bereich der Befestigungen (Befestigungsmaße siehe 7.1)
plan sein und das Material für das Gewicht des FX15 geeignet sein.
HINWEIS
WARNUNG
DE
DE
DE
218095/FX1560300010
2013-08-27·BA00·III·de·02
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
7
DE
1
2
3
4
5
6
7
DE
Installation
7.4Einbaubedingungen Netzanschluss
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
Kabeleinführung in das Gerät
WARNUNG
Bei Verwendung nicht zugelassener Kabelverschraubungen ist der
Explosionsschutz nicht gewährleistet!
Es dürfen nur Kabelverschraubungen mit entsprechender Bescheinigung
verwendet werden. Diese müssen druckfest (Ex d) und für die jeweils
verwendete Kabelart geeignet sein sowie die Anforderungen der
IEC/EN 60079-14 erfüllen.
Die Temperatur der Leitungseinführung kann 70 °C erreichen.
Zur Gewährleistung der erforderlichen IP-Schutzart muss die Installation
der Kabelverschraubung den Herstelleranweisungen entsprechend
erfolgen.
Für unbenutzte Bohrungen im Gehäuse sind Ex d Verschlussstopfen,
für unbenutzte Kabelverschraubungen Ex d Stopfen zu verwenden.
Es ist darauf zu achten, dass für diese Bauteile eine entsprechende
Zulassung vorliegt und die Anforderungen der IEC/EN 60079-14 erfüllt
sind.
Zur Erfüllung der Schutzart IP 66 müssen alle Gewindekabeleinführungen
mit einer entsprechend bescheinigten Komponente ausgestattet und das
Gewinde mit einem geeigneten, nichthärtenden Gewindedichtungsstoff
abgedichtet sein.
DE
DE
DE
DE
DE
DE
7.5Anschluss an Leiterplatte
Explosionsdarstellung zum Anschluss an die Leiterplatte FX15
1 Zylinderkopfschrauben
2 Blitzlampenaufbau
3 Dicht-O-Ring
4 Blitzröhre, befestigt an der oberen
-Blitzlampenaufbau anheben und obere und untere Leiterplatte lösen
-Blitzlampenaufbau sowie obere Leiterplatte und die Klemme zur unteren Leiterplatte
beiseite legen
8
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
218095/FX1560300010
2013-08-27·BA00·III·de·02
7.6Zusammenbau des Gehäuses
6
2
5
4
3
1
3
1
TELEPHONE
INITIATE
TB4
LIVE (V )AC
24/48 V DC
TB2
NEUTRAL
0V
TB1TB3
N
L
N
L
TELEPHONE
INITIATE
TB4
LIVE (V )AC
24/48 V DC
TB2
NEUTRAL
0V
TB1TB3
0 V
+V
0 V
+V
-Bei angeschlossenen Leitungen obere und untere Leiterplatte wieder anschließen.
-Blitzlampenaufbau vorsichtig in Sockel einsetzen und beim Einbau darauf achten,
dass der Aufbau gerade in den Sockel eingesetzt wird. Keine Kraft anwenden.
Geht man mit Geduld vor, so lässt sich der Aufbau problemlos einsetzen.
-Zylinderkopfschrauben wieder festschrauben.
Die Zylinderkopfschrauben sind mit einem Drehmoment von 3 bis 3,05 Nm
An den Klemmen können Drähte mit 2.5 mm2 bzw. 14 ... 18 AWG
angeschlossen werden.
15757E00
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
7.7.3 Schaltpläne
Schaltplan FX15 ACSchaltplan FX15 DC
218095/FX1560300010
2013-08-27·BA00·III·de·02
15759E0015758E00
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
9
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
Inbetriebnahme
7.8Erdanschluss
-Das Gerät FX15 muss mit einem qualitativ hochwertigen Erdungsanschluss versehen
sein.
-Der interne Erdungsanschluss ist der Primäranschlusspunkt. Der externe Anschluss
ist eine zusätzliche Potentialausgleichsleitung und kommt dann zum Einsatz, wenn
eine derartige Leitung aufgrund der örtlichen Gesetzgebung oder von seiten der
Behörden zulässig oder erforderlich ist.
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
15761E00
8Inbetriebnahme
WARNUNG
Gerät vor der Inbetriebnahme überprüfen!
Um einen ordnungsgemäßen Betrieb sicherzustellen, muss das Gerät vor der
Inbetriebnahme überprüft werden.
Stellen Sie vor der Inbetriebnahme sicher, dass:
-keine Komponenten beschädigt sind
-das Gerät vorschriftsmäßig installiert ist
-sich keine Fremdkörper im Gerät befinden
-alle Schrauben und Muttern fest angezogen sind
-die vorgeschriebenen Anzugsdrehmomente eingehalten sind
-der Anschluss ordnungsgemäß ausgeführt ist
9Instandhaltung, Wartung und Störbeseitigung
WARNUNG
Gefahr durch unbefugte Arbeiten am Gerät!
Verletzungen und Sachschäden drohen.
Montage, Installation, Inbetriebnahme, Betrieb und Wartung dürfen
ausschließlich von dazu befugtem und entsprechend geschultem Personal
durchgeführt werden.
9.1Regelmäßige Wartungsarbeiten
-Art und Umfang der Prüfungen den entsprechenden nationalen Vorschriften
(z.B. IEC/EN 60079-17) entnehmen.
-Die Fristen so bemessen, dass entstehende Mängel in der Anlage, mit denen zu
rechnen ist, rechtzeitig festgestellt werden.
Im Rahmen der Wartung prüfen:
-Leitungen auf festen Sitz.
-Gerät auf sichtbare Schäden.
-Einhaltung der zulässigen Temperaturen gem. IEC/EN 60079-0.
-Bestimmungsgemäße Verwendung.
10
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
218095/FX1560300010
2013-08-27·BA00·III·de·02
10Reinigung
152 mm / 5.98 "
78 mm / 3.07 "
180 mm / 7.09 "
28 mm
1.10 "
25 mm
0.98 "
ø 8,50 mm
ø 0.33 "
87 mm / 3.43 "
20 mm
0.79 "
75 mm / 2.95 "
ø 9 mm
ø 0.35 "
105 mm / 4.13 "
-Reinigung mit einem Tuch, Besen, Staubsauger o.ä.
-Bei feuchter Reinigung Wasser oder milde, nicht scheuernde, nicht kratzende
Reinigungsmittel verwenden.
-Niemals aggressive Reinigungsmittel oder Lösungsmittel verwenden.
11Entsorgung
-Beachten Sie die nationalen Vorschriften zur Abfallbeseitigung.
12Zubehör und Ersatzteile
Reinigung
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
WARNUNG
Kein Explosionsschutz bei falschem Zubehör!
Es dürfen nur Original-Ersatzteile der Firma R. STAHL verwendet werden.
Das Gerät wird ohne Winkel ausgeliefert. Nachfolgende Edelstahl-Winkel sind als
Zubehör erhätlich:
Griffrückenwinkel
15741E0015743E0015763E00
Isometrische Ansicht eines
Montagewinkels FX15
Anschraubmaße MontagewinkelFX15 mit Montagewinkel
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
DE
‘L’-Winkel
Isometrische Ansicht eines
L-förmigen Montagewinkels
218095/FX1560300010
2013-08-27·BA00·III·de·02
15740E0015742E0015762E00
Anschraubmaße L-förmiger WinkelFX15 mit L-förmigem
Montagewinkel
GRP Explosionsgeschütztes
optisches Signalgerät 5 Joule
Reihe FX15
11
DE
DE
DE
DE
DE
DE
DE
DE
Zubehör und Ersatzteile
Es ist erlaubt, bestimmte Komponenten des Gerätes FX15 auszutauschen.
Folgende Teile können käuflich erworben werden
Conformity with standards and regulations is specified in the corresponding certificates
and the EC Declaration of Conformity. These documents can be downloaded from our
homepage www.stahl-ex.com.
R. STAHL Schaltgeräte GmbH
Am Bahnhof 30
74638 Waldenburg
Germany
T
F
+49 7942 943-0
+49 7942 943-4333
www.stahl-ex.com
2
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
218095/FX1560300010
2013-08-27·BA00·III·en·02
2Symbols Used
Safety instructions
Non-observance can result in damage to equipment, serious injuries or
death.
The safety instructions contained in these operating instructions and affixed
to the device must be observed!
Symbols Used
EN
EN
EN
EN
EN
EN
Warning symbol
Danger due to explosive atmosphere!
Warning symbol
Danger due to live parts!
Notice
This graphic marks important additional information, tips and
recommendations.
3General Safety Notes
3.1Storage of these Operating Instructions
Read these operating instructions carefully and store them near the installation place. For
correct operation, please observe all other documents enclosed in this delivery and the
operating instructions of the equipment to be connected.
WARNING
Use the devices only for their intended purpose!
We cannot be held liable for damage caused by an incorrect or unauthorized
use or by non-observance of these operating instructions.
Use the device only if it is undamaged.
WARNING
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Any unauthorized work on the device is prohibited!
Installation, maintenance, overhaul and repair may only be carried out by
appropriately authorized and trained personnel.
Observe the following information during installation and operation:
-Any damage may compromise the explosion protection
-National and local safety regulations
-National and local accident prevention regulations
-National and local assembly and installation regulations
-Generally recognized technical regulations
-Safety notes in these operating instructions
-Characteristic values and rated operating conditions on the rating plates and
data plates
-Additional information plates on the device
218095/FX1560300010
2013-08-27·BA00·III·en·02
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
3
EN
IIBEx d IIB T* Gb (Ta = -60 … +** °C)
Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IICEx d IIC T* Gb (Ta = -60 … +** °C)
Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IIBEII 2 G Ex d IIB T* Gb (Ta = -60 … +** °C)
EII 2 D Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
IICEII 2 G Ex d IIC T* Gb (Ta = -60 … +** °C)
EII 2 D Ex tb IIIC T***°C Db IP 66 (Ta = -60 … +** °C)
EN
EN
EN
EN
EN
EN
EN
EN
Intended Use
3.2Alterations and Modifications
WARNING
Alterations and modifications to the device are not permitted.
We shall not accept any liability or warranty obligations for damage resulting
from alterations and modifications.
3.3Special Versions
In case of additional/different order options, special versions may differ from the
description given here.
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
4Intended Use
The explosion proof visual signal series FX15 provides a flashing visual signal intended
to alert, warn or draw attention to an event. It has been designed for use in hazardous
and/or harsh environments. In hazardous areas the devices have explosion protection for
ATEX/IECEx zones 1 + 2 for gas and 21 + 22 for dust. The device is suitable for
Gas groups IIB or IIC, Dust group IIIC.
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
218095/FX1560300010
2013-08-27·BA00·III·en·02
7.2Installation Conditions
Risk of electric shock!
Before opening the device, disconnect it from the power supply.
WARNING
Installation
EN
EN
EN
EN
EN
WARNING
No explosion protection if components are damaged or incorrectly
installed!
Operate the device only if it is not damaged.
If the thread is damaged, the device must be replaced immediately.
Take extreme care when handling the device and internal components.
Particular care is needed when accessing the PCB for installation.
Exposed joint surfaces must be protected and not have contact with dust
or dirt, or be knocked against any object.
The end flanges must be fitted squarely and on no account is force to be
used.
The flange must not be hammered, levered with a metal instrument or the
fixing screws used to pull down the flange.
With care and patience, it will be found that the flange enters the body
without difficulty.
Install the device only in a clean and dry operating environment.
NOTE
Check the following:
Do you have the correct device to satisfy the system specification?
Are the gas group and temperature range of the product suitable for the
intended application?
Is the supply voltage correct?
Is the strobe the correct colour?
Is a suitable mounting location available?
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
7.3Assembling and Operating Position
Incorrectly installed components!
Explosion protection cannot be guaranteed any more if the components
are incorrectly installed.
When terminal sleeves are fitted, they must be gas-tight and applied with
a suitable tool.
-Select a suitable location with regard to the area to be covered by the FX15.
-The surface should be flat in the area of the fixings (See 7.1 for fastening dimensions)
and the material suitable to carry the weight of the FX15.
218095/FX1560300010
2013-08-27·BA00·III·en·02
WARNING
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
7
EN
1
2
3
4
5
6
7
EN
Installation
7.4Installation Conditions for Electrical Connections
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Cable entry to device
WARNING
No explosion protection if non-approved cable glands are used!
Only cable glands with a corresponding certificate may be used.
They must be flameproof (Ex d), suitable for the type of cable used and
fulfil the requirements of IEC/EN 60079-14.
Cable entry temperature may reach 70 °C.
To ensure the required ingress protection, installation of the cable gland
must be performed in accordance with the manufacturer's instructions.
For unused enclosure holes use Ex d stopping plugs, for unused cable
glands Ex d plugs. Make sure that these components have an appropriate
approval and fulfil the requirements of IEC/EN 60079-14.
All threaded cable entries to be fitted with an appropriately certified
component and the thread sealed with a suitable non-setting thread
sealant to maintain IP 66 rating.
7.5Access to the PCB
1 Socket head screws
2 Strobe assembly
3 Sealing O ring
4 Flash tube, attached to upper PCB
5 Cheese head screws
6 Lower PCB
7 Device base
EN
EN
EN
15755E00
Exploded diagram accessing the PCB FX15
Instructions
-Remove socket head screws x 6
-Lift strobe assembly and disconnect upper and lower PCB’s
-Set aside strobe assembly and upper PCB and terminal to lower PCB
8
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
218095/FX1560300010
2013-08-27·BA00·III·en·02
7.6Reassembly of Enclosure
6
2
5
4
3
1
3
1
TELEPHONE
INITIATE
TB4
LIVE (V )AC
24/48 V DC
TB2
NEUTRAL
0V
TB1TB3
N
L
N
L
TELEPHONE
INITIATE
TB4
LIVE (V )AC
24/48 V DC
TB2
NEUTRAL
0V
TB1TB3
0 V
+V
0 V
+V
-With wires terminated, reconnect upper and lower PCB.
-Carefully insert strobe assembly into base, take care when fitting the assembly it must
be fitted squarely into the base. Do not use force, with patience it will be found that the
assembly enters without difficultly.
-Replace socket head screws.
Socket head screws should be tightened with a torque of 3 to 3.05 Nom.
Installation
EN
EN
EN
EN
EN
EN
NOTE
EN
EN
7.7Electrical Connection
7.7.1 Key Components
Key components FX15Lower PCB key components FX15
7.7.2 Cable Connection
7.7.3 Wiring Diagrams
The terminals accept wires of 2.5 mm2 or 14 ... 18 AWG.
15756E00
NOTE
1Terminals
2 Lower PCB base board
3 PCB connector
4 Connecting wire
5 Upper PCB base wire
6 Flash tube
15757E00
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Wiring diagram FX15 ACWiring diagram FX15 DC
218095/FX1560300010
2013-08-27·BA00·III·en·02
15759E0015758E00
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
9
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Putting into Service
7.8Earth Connection
-FX15 must be connected to a good quality earth.
-The internal Earth connection is the primary point. The external connection is for a
supplementary bonding connection and is used where local code or authorities permit
or require such connection.
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
15761E00
8Putting into Service
WARNING
Check the device before commissioning!
To ensure the correct operation, check the device before commissioning.
Before commissioning, ensure that:
-no components are damaged
-the device has been installed according to regulations
-there are no foreign bodies inside the device
-all screws and nuts have been firmly tightened
-the prescribed tightening torques have been observed
-connection has been made correctly
9Maintenance, Overhaul and Repair
WARNING
Risk due to unauthorized work being performed on the device!
Risk of injury and damage to equipment.
Assembly, installation, commissioning, operation and maintenance must
only be carried out by appropriately authorized and trained personnel.
9.1Regular Maintenance Work
-Consult the relevant national regulations (e.g. IEC/EN 60079-17) to determine the type
and extent of inspections.
-Plan the intervals such that any expected defects in the equipment are detected
promptly.
To check as part of maintenance:
-Check if the cables are clamped properly.
-Inspect the device for signs of visible damage.
-Compliance with the permitted temperatures in accordance with IEC/EN 60079-0.
-Make sure that the device is used according to its designated use.
10
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
218095/FX1560300010
2013-08-27·BA00·III·en·02
10Cleaning
152 mm / 5.98 "
78 mm / 3.07 "
180 mm / 7.09 "
28 mm
1.10 "
25 mm
0.98 "
ø 8,50 mm
ø 0.33 "
87 mm / 3.43 "
20 mm
0.79 "
75 mm / 2.95 "
ø 9 mm
ø 0.35 "
105 mm / 4.13 "
-Clean with a cloth, brush, vacuum cleaner or similar items.
-When cleaning with a damp cloth, use water or mild, non-abrasive, non-scratching
cleaning agents.
-Never use aggressive cleaning agents or solvents.
11Disposal
-Observe the national waste disposal regulations.
12Accessories and Spare Parts
Cleaning
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
WARNING
If wrong accessories are used, explosion protection cannot be
guaranteed!
Use only original R. STAHL spare parts.
The FX15 is sold without a bracket, customers can choose from the following stainless
steel brackets:
Backstrap bracket
15741E0015743E0015763E00
Isometric view of
FX15 mounting bracket
Mounting bracket
bolting dimensions
FX15 with mounting bracket
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
‘L’ Bracket
Isometric view of
L-shaped mounting bracket
218095/FX1560300010
2013-08-27·BA00·III·en·02
15740E0015742E0015762E00
L-shaped bracket
bolting dimensions
GRP Explosion Proof Visual
Signal 5 Joule
Series FX15
FX15 with mounting L-shaped
bracket
11
EN
EN
EN
EN
EN
EN
EN
EN
Accessories and Spare Parts
It is permitted for customers to replace certain components of the FX15.
The following parts are available for sale