!
User Manual
HEADBANGER10
SLI MHW HB10
!
Table of Contents
1.BEFORE USAGE
This package contains
Unpacking
Introduction
Specifications
Features
2.INSTALLATION
Installation requirements
Power Connection
DMX Serial Data Link
3. OPERATION
Menu Map
Operating Instructions
DMX Channels
!
1. BEFORE USAGE
This package contains
• 1x HeadBanger 10
• 1x Power Cable
• 1x User Manual
Unpacking
• Thank you for purchasing this product, it has been thoroughly tested
and has been shipped in perfect operating condition.
• Carefully check the packaging for damage that may have occurred during
shipping.
• If the packaging appears to be damaged, carefully inspect your fixture
for any damage and be sure all equipment necessary to operate the unit has
arrived intact.
• If damage has been found or parts are missing, please contact your vendor or
our customer support number for further instructions.
Introduction
• This fixture can operate in six different operating modes: DMX control, sound
active, automatic, manual setup, infrared remote control or in a Master/Slave
configuration
• This product comes with several built-in programs that can be used while
operating as a single unit or with multiple units linked in a master/slave
configuration
• For best results use fog or special effects smoke to enhance the beam
projection
• Warning! To prevent or reduce the risk of electrical shock or fire, do not
expose this unit to rain or moisture.
• Warning! This product may cause severe eye damage. Avoid looking directly
into the light source at all times!
!
Specifications
• Voltage: AC100V～240V, 50-60Hz
• Power Consumption: 80W
• Light source: 7x 10W RGBW 4 in 1 LED
• Beam angle: 25°
• Max output @1m: 6100 Lux
• PAN 540°, Tilt 270° with 16bit control
• DMX channels: 7 or 12 DMX Channels
• Packing Dimensions: 210x210x140mm
• Net weight: 2,75 Kg
Features
• 3PIN XLR DMX in and out
• IEC power in and out
• 4 control modes: DMX512, automatic programs, sound control, mast/slave
• LCD display for easy setup
• Indoor operation temperature range: -20°C～+40°C
• Dimmer: 0-100%
• Strobe 0-10Hz
Please Note: Specifications and improvements in the design of this unit and this
manual are subject to change without any prior written notice.
2. INSTALL ATION
Installation requirements
• The product can be hung or placed on a solid surface
• If you install the light in a hanging position, always use a suitable mounting
position and a clamp or screw that is strong enough to hold the product
without stress. Always use a safety wire to secure the light.
• Always keep a distance of minimum 0.5m to all objects or persons
• Installation should always be done by a trained professional.
• Make sure the light always has good ventilation
• It is recommended to always use 110 Ohm DMX cable to prevent data
corruption of your DMX control signal
!
Power connection
The equipment has an auto-switching power supply that can accommodate a
wide range of input voltages. The only thing necessary to do before powering on
the unit is to make sure the line voltage you are applying is within the range of
accepted voltages. This equipment will accommodate between 100V and 240v
AC 50-60HZ. It is possible to daisy chain the power connection from one fixture
to the next. We recommend not connecting more than 30 fixtures on one 16A
220V socket and not more than 15 fixtures on one 16A 110V socket.
Color
Connection
PIN
Brown
AC live wire
1
Blue
AC zero curve
2
Green/Yellow
AC ground wire
3
DMX Serial Data Link
1. Connect the male 3pin DMX input of the first fixture to the female 3pin DMX
output of the lighting controller using 110 Ohm DMX cable, for example a Stagg
Commandor 10 (skip this step when not using a controller)
2. Connect the output of the first fixture to the input of the next fixture using 110
Ohm DMX cable. Repeat this process until you reach your last fixture. Here it is
recommended to connect a DMX terminator to the output of the last fixture in the
chain.
!
3. OPERATION
Menu Map
ADDR
DMX Adress
A001-A512
CHND
Channel Mode
7CH/12CH
SLND
Master/Slave
NAST/SL1/SL2
SOUN
Sound Sensitivity
0-100
AUTO
Auto Mode
NO/YES
STBY
Standby
NO/YES
PAN
PAN Reverse
NO/YES
TILT
TILT Reverse
NO/YES
LED
LED On/Off
ON/OFF
DISP
Display On/Off
ON/OFF
TEST
Self Test
HOUR
Show Total Runtime
RSET
Reset
!
Operating Instructions
Take note: All changes made to the unit become active and saved when the unit
exits it's menu. This is activated by not touching the control buttons for 5
seconds. The unit will then display the active running mode (NST/SL1/SL2 for
Sound Control, AUTO for Automatic Programs or the DMX address when DMX
input is detected).
ADDR - DMX Address Setup
• Press MENU, then Up or DOWN until "ADDR" is displayed, then press ENTER
• Change the DMX address by pressing UP or DOWN
• Press ENTER to save the DMX address
CHND - DMX Channel Modes
• Press MENU, then UP or DOWN until "Chnd" is displayed, then press ENTER
• "X Ch" will now be displayed. "X" represents the DMX mode you have
selected (see DMX channel charts for reference). Choose your desired DMX
mode with UP or DOWN and press ENTER to confirm.
SLND - Master/Slave Setup
• Press MENU, then UP or DOWN until "SLND" is displayed, then press
ENTER
• "Nast": The unit becomes the master in the Master/Slave chain and should be
the first light in it. All slave lights should be daisy-chained from the output of
the master
• "SL1/SL2": The unit becomes a slave unit that follows the master unit when
Automatic Programs or Sound Control is activated. SL1 does exactly the
same, SL2 puts a little offset on the program so it does not run symmetrical
and gives dynamic to the show.
• Press ENTER to confirm
SOUN - Sound Sensitivity Setup
• Press MENU, then UP or DOWN until "SOUN" is displayed, then press
ENTER
• You can adjust the sensitivity of the internal microphone using the UP or
DOWN buttons, press ENTER to confirm.
!
AUTO - Automatic Programs Setup
• Press MENU, then Up or DOWN until "AUTO" is displayed, then press ENTER
• "Yes": When this option is selected, the HeadBanger 10 will run automatic
programs if there is no DMX input signal detected.
• "No": When this option is selected, Automatic programs are disabled and the
HeadBanger 10 will use Sound Controlled Programs when no DMX input
signal is detected.
• Press ENTER to confirm
STBY - Standby setup
• Press MENU, then UP or DOWN until "STBY" is displayed, then press ENTER
• "Yes": When no DMX input is detected, the unit will bypass sound controlled
programs or automatic programs and enter standby mode.
• "No": When no DMX input is detected, the unit will activate either sound
control or automatic programs.
• Press ENTER to confirm
PAN - Pan Inversion
• Press MENU, then UP or DOWN until "PAN" is displayed, then press ENTER
• "Yes": The unit inverts the PAN (vertical) movement (up becomes down)
• "No": The unit's PAN movement is run normally.
• Press ENTER to confirm
TILT - Tilt Inversion
• Press MENU, then UP or DOWN until "TILT" is displayed, then press ENTER
• "Yes": The unit inverts the TILT (horizontal) movement (left becomes right)
• "No": The unit's TILT movement is run normally.
LED - Display on/off
• Press MENU, then UP or DOWN until "LED" is displayed, then press ENTER
• "On": When the unit exits the menu and enter run mode, the display will
remain lit and will show the current status
• "Off": When the unit exits the menu and enter run mode, the display will turn off.
!
DISP - Display Inversion
• Press MENU, then UP or DOWN until "DISP" is displayed, then press ENTER
• By pressing ENTER, the unit's display can be inverted so that when the light
is hung upside-down, the display will still be properly readable by the user.
TEST - Self-Test
• Press MENU, then UP or DOWN until "TEST" is displayed, then press ENTER
• The unit will run a self-test program, testing all the features individually.
Press MENU to exit.
HOUR - Runtime
• Press MENU, then UP or DOWN until "HOUR" is displayed, then press ENTER
• The total running time of the unit is displayed, press MENU to exit.
RSET - Reset
• Press MENU, then UP or DOWN until "SLav" is displayed, then press ENTER
• The current software version is displayed, press MENU to exit.
DMX Channels
7 Channels Mode
CHANNEL
VALUE
FUNCTION
1
0
Stop
1~255
Adjust Pan
2
0
Stop
1~255
Adjust Tilt
3
0~200
Dimmer
201-255
Strobe
4
0
Close
1~255
Red
5
0
Close
1~255
Green
6
0
Close
1~255
Blue
7
0
Close
1~255
White
!
12 Channels Mode
CHANNEL
VALUE
FUNCTION
1
0
Stop
1~255
Adjust Pan
2
0
Stop
1~255
Adjust Pan fine
3
0
Stop
1~255
Adjust Tilt
4
0
Stop
1~255
Adjust Tilt fine
5
0~10
Close
11~255
Dimmer
6
0
Close
1~255
Red
7
0
Close
1~255
Green
8
0
Close
1~255
Blue
9
0
Close
1~255
White
10
0~9
Close
10~255
Color Macros
11
0~9
No strobe
10~255
Strobe (slow to fast)
12
0~127
Disable sound active mode
128~255
Activate sound active mode
!
!
!
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS.
• If, after you have followed the instructions outlined above, this device fails to function, please
contact your dealer. Under no circumstances should this device be opened. Leave all servicing to
qualified personnel.
•Electrical appliances must never be used in conditions of high humidity or heat. To prevent any risk
of fire or electric shock, never spill or splash liquids on this device. Should this happen, unplug the
power cable from the mains outlet and switch off the mixer immediately.
MARKING & CONFORMITY
1. The CE mark on this product means it conforms to the EMC Directive (2004/108/CE), CE marking
Directive (93/68/EEC) and Low Voltage Directive (2006/95/EC).
2. The «Crossed-out Wheeled Bin» is to draw your attention to the WEEE (Waste Electric &
Electronic Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately
for recycling.
3. «RoHS compliant» means this device conforms to the Directive (2002/95EC) on the restriction of
the use of certain hazardous substances in electrical and electronic equipments, such as: Mercury,
Lead, Cadmium, Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated
Diphenyl Ethers (PBDE).
Loading...