USER MANUAL
Baryonic 24
SLB-244-41
Please read the instructions carefully before use
!
SAFETY INSTRUCTIONS
Please read the instructions carefully as they include important
information about the installation, operation and maintenance.
• Please keep this user’s guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
• All fixtures leave the manufacturer intact. Please note that any damages incurred
by the user is not covered by the guarantee.
• Unpack and check carefully that there is no transportation damage before using the
unit.
• The unit is for indoor use only. Use only in a dry location.
• Use a safety bond when attaching the fixture to a lighting rig. Handle by the
hanging bracket when fixing.
• The unit must be installed in a location with adequate ventilation at least 50 cm
from adjacent surfaces.
• Make sure that no ventilation slot is blocked, otherwise the unit will overheat.
• Before operating, ensure that the voltage and frequency of the power supply match
the power requirements of the unit.
• Make sure all equipment is properly earthed.
• Do not operate the unit if the ambient temperature is higher than 40°C.
• Do not hardwire to any mains dimmer.
• On the first start, there may be some normal operational start-up smell.
• Make sure that there is no flammable material close to the unit while operating, as
it is a fire hazard.
• Examine power wires carefully and replace immediately if there is any damage.
• Never run on for a long time lest shortening lifespan. Avoid any inflammable liquids,
water or metal objects entering the unit. In case it happens, cut off the mains power
immediately.
• Do not operate in a dirty or dusty environment. Clean fixtures regularly.
• Do not allow children unsupervised to operate the fixture.
• Do not touch any wire during operation as there might be a hazard of electric
shock.
• Avoid placing power wires next to other cables.
• Disconnect the mains power before replacing or servicing the fuses.
• Replace fuse only with the same type.
• In the event of a serious operating problem, stop using the unit immediately.
• Never turn on and off the unit time after time.
• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
• Do not open the unit as there is no user serviceable part inside.
• Never try to repair the unit by yourself. Repairs carried out by unskilled people can
lead to damage or malfunction. Please contact the nearest authorized technical
assistance centre.
• Disconnect the mains power if the fixture is not used for a long time.
• Use the original packaging to transport regarding any warranty issue.
• Do not look directly at the LED light beam while the fixture is on.
• Do not connect more than 7 units to the same power source.
INSTALLATION
The feet should be mounted on each sides of the unit. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and able to support 10 times
the unit’s weight. Also, always use a safety cable that can hold 12 times the unit’s
weight when installing the fixture.
The equipment must be fixed in an appropriate place by professionals. Keep it out of
the reach of unqualified people.
TECHNICAL SPECIFICATIONS
Architectural colour bar with 24x4w 4in1 RGBW LED
- LED: 24x4W 4in1 RGBW
- LED beam angle: 35°
- Functions: colour chaser, strobe and colour mix
- Protocol: DMX 512. 6, 9, 16, 30 or 58 channels
- Control modes: DMX 512, master/slave, sound activation, automatic,
remote control
- Connectivity: 3-pin XLR cable and IEC
- 4-Digits on rear panel
- Power consumption: 100W
- Weight: 4kg (8.8lb)
- Dimensions: 110 x 10 x 10 cm (4.3“ x 0.4“ x 0.4“)
- Included: Mounting feet
SETTING UP THE DEVICE
DMX Mode
With the menu button, select the DMX mode (dxxx) and press the enter key to
confirm. Then use the up and down buttons to choose the desired DMX channel (1 –
512) and press the enter key to confirm. Press the menu button to return to the main
menu.
Use the menu button and the up and down buttons and go to “Chnd” to select the
desired Dmx channel mode: 6, 9, 16, 30 or 52 channels. See following charts for
channels functions information.
6 Channels:
Channel
Value
Function
1
0-255
Red 0-100%
2
0-255
Green 0-100%
3
0-255
Blue 0-100%
4
0-255
White 0-100%
5
0-255
See Colour
Chase Table
6
0-255
Chase Speed
Slow to Fast
9 Channels:
Channel
Value
Function
1
0-255
All dimming
2
0-255
Strobe
3
0-255
Red 0-100%
4
0-255
Green 0-100%
5
0-255
Blue 0-100%
6
0-255
White 0-100%
7
0-255
Auto program
8
0-255
See Colour
Chase Table
9
0-255
Chase Speed
Slow to Fast
16 Channels:
Channel
Value
Function
1
0-255
All dimming 1
2
0-255
Strobe
3
0-255
Red 1 0-100%
4
0-255
Green 1 0-100%
5
0-255
Blue 1 0-100%
6
0-255
White1 0-100%
7
0-255
Auto program
8
0-255
All dimming 2
9
0-255
Strobe
10
0-255
Red 2 0-100%
11
0-255
Green 2 0-100%
12
0-255
Blue 2 0-100%
13
0-255
White2 0-100%
14
0-255
Auto program
15
0-255
See Colour Chase Table
16
0-255
Chase Speed Slow to Fast
30 Channels:
Channel
Value
Function
1
0-255
All dimming 1
2
0-255
Strobe1
3
0-255
Red 1 0-100%
4
0-255
Green 1 0-100%
5
0-255
Blue 1 0-100%
6
0-255
White1 0-100%
7
0-255
Auto program1
8
0-255
All dimming 2
9
0-255
Strobe2
10
0-255
Red 2 0-100%
11
0-255
Green 2 0-100%
12
0-255
Blue 2 0-100%
13
0-255
White2 0-100%
14
0-255
Auto program2
15
0-255
All dimming 3
16
0-255
Strobe3
17
0-255
Red 3 0-100%
18
0-255
Green 3 0-100%
19
0-255
Blue 3 0-100%
20
0-255
White3 0-100%
21
0-255
Auto program3
22
0-255
All dimming 4
23
0-255
Strobe4
24
0-255
Red 4 0-100%
25
0-255
Green 4 0-100%
26
0-255
Blue 4 0-100%
27
0-255
White4 0-100%
28
0-255
Auto program4
29
0-255
See Colour Chase Table
30
0-255
Chase Speed Slow to Fast
58 channels:
Channel
Value
Function
1
0-255
All dimming 1
2
0-255
Strobe1
3
0-255
Red 1 0-100%
4
0-255
Green 1 0-100%
5
0-255
Blue 1 0-100%
6
0-255
White1 0-100%
7
0-255
Auto program1
8
0-255
All dimming 2
9
0-255
Strobe2
10
0-255
Red 2 0-100%
11
0-255
Green 2 0-100%
12
0-255
Blue 2 0-100%
13
0-255
White2 0-100%
14
0-255
Auto program2
15
0-255
All dimming 3
16
0-255
Strobe3
17
0-255
Red 3 0-100%
18
0-255
Green 3 0-100%
19
0-255
Blue 3 0-100%
20
0-255
White3 0-100%
21
0-255
Auto program3
22
0-255
All dimming 4
23
0-255
Strobe4
24
0-255
Red 4 0-100%
25
0-255
Green 4 0-100%
26
0-255
Blue 4 0-100%
27
0-255
White4 0-100%
28
0-255
Auto program4
29
0-255
All dimming 5
30
0-255
Strobe5
31
0-255
Red 5 0-100%
32
0-255
Green 5 0-100%
33
0-255
Blue 5 0-100%
34
0-255
White5 0-100%
35
0-255
Auto program5
36
0-255
All dimming 6
37
0-255
Strobe6
38
0-255
Red 6 0-100%
39
0-255
Green 6 0-100%
40
0-255
Blue 6 0-100%
41
0-255
White6 0-100%
42
0-255
Auto program6
43
0-255
All dimming 7
44
0-255
Strobe7
45
0-255
Red 7 0-100%
46
0-255
Green 7 0-100%
47
0-255
Blue 7 0-100%
48
0-255
White7 0-100%
49
0-255
Auto program7
50
0-255
All dimming 8
51
0-255
Strobe8
52
0-255
Red 8 0-100%
53
0-255
Green 8 0-100%
54
0-255
Blue 8 0-100%
55
0-255
White8 0-100%
56
0-255
Auto program8
57
0-255
See Colour Chase Table
58
0-255
Chase Speed Slow to
Fast
Colour Chase Table
Colour Chase
000-007 No function
No Function
008-022 Colour Chase 01
Colour Effect 1
023-037 Colour Chase 02
Colour Effect 2
038-052 Colour Chase 03
Colour Effect 3
053-067 Colour Chase 04
Colour Effect 4
068-082 Colour Chase 05
Colour Effect 5
083-097 Color Chase06
Colour Effect 6
098-112 Colour Chase 07
Colour Effect 7
113-127 Colour Chase 08
Colour Effect 8
128-142 Colour Chase 09
Colour Effect 9
143-157 Colour Chase10
Colour Effect 10
158-172 Colour Chase 11
Colour Effect 11
173-187 Colour Chase 12
Colour Effect 12
188-202 Colour Chase 13
Colour Effect 13
203-217 Colour Chase 14
Colour Effect 14
218-232 Colour Chase 15
Colour Effect 15
233-247 Colour Chase 16
Colour Effect 16
248-255 Sound active
Sound Effect 1-16
Master/Slave mode
With the menu button, select the slave mode (Sindh) and press the enter key to
confirm. Then use the up and down buttons to choose between Master (Mast), Slave
1(SL 1) or Slave 2 (SL 2).
Thanks to this mode, you can connect several Baryonic 24 in a daisy chain and
make a nice lightshow. All the units will play in the same rhythm. To do so, put the
first light in your chain in “master” mode. Put the other ones in Slave 1 or 2. Slave 1
and 2 will react in a different way to do a more complex lightshow.
Sound Mode
With the menu button, select the Sound mode (SoUn) and press the enter key to
confirm. Then use the up and down buttons to select the desired preset from Sn01 to
Sn16. You can also change the sensibility of the internal microphone (Se__) to make
it react as close as possible to the basses of the music.
In this mode, the Baryonic will react to the music to create a rhythmic lightshow.
Automatic mode
With the menu button, select the automatic mode (Auto) and press the enter key to
confirm. Then use the up and down buttons to select the desired auto-lightshow
(from Au01 to Au10) and press enter. Then select the appropriate speed (from Sp1
to Sp9) and press enter. In this mode, the fixture will play an automatic sequence at
a constant speed.
Colour mode:
With the menu button, select the Red, Green, blue or white and press the enter key
to confirm. Then use the up and down buttons to increase or decrease the colour
amount (from 001 to 255).
Thanks to this colour mixing mode, you can virtually choose all the desired fixed
colours.
Display mode (Disp)
This function allows you to flip the display. This is useful if you hang the Baryonic 24
upsides down.
User mode
This function display the actual software version.
DMX512 CONNECTIONS
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
Warning
To avoid signal transmission problems and interferences when using fixtures in
chain, use a Stagg N-series professional 3-pin DMX terminator (resistance: 120
ohms; pin2: DMX-; pin3:DMX+).
FIXTURE CLEANING
A cleaning must be carried out periodically to optimize the light output. The cleaning
frequency depends on the environment in which the fixture operates: A damp, smoky
or particularly dirty surrounding can cause greater accumulation of dirt on the
fixture’s optics. Clean the fixture with a soft cloth and normal glass cleaning fluid.
Always dry the parts carefully. Clean the external optics at least every 20 days.
For more info and the latest product updates:
staggmusic.com
EMD Music S.A.
Boulevard Général Wahis 16A
1030 Brussels
Belgium
05/2018
Loading...