Stagg 250 GARH EU+UK, 250 GAR212 EU+UK User Manual
FRONT PANEL
1) INPUT - Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2) (CLEAN) VOLUME - This control determines the output volume of the amplier’s clean channel.
3) CHANNEL SELECT - This button can be used to switch between the Clean and Overdrive channels.
Alternatively, you may also select the channel via a footswitch (see FOOTSWITCH).
4) (OVERDRIVE) LED - This red LED lights up when the Overdrive channel is activated.
5) (OVERDRIVE) GAIN - This control determines the distortion intensity of the amplier’s overdrive
setting. Adding GAIN will make your guitar sound more distorted.
6) (OVERDRIVE) MASTER - This control determines the output volume of the amplier’s Overdrive
channel. Adding MASTER will make your guitar sound louder and more percussive.
7) BASS - This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
8) MID - This control determines the level of middle frequencies in the output signal. Adding MID will
make your guitar sound rounder and fuller.
9) TREBLE - This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
10) (SPRING) REVERB - This is the reverb intensity control. This controls the amount of reverb that
is added back to the original dry signal. Adding REVERB will produce a reverberation effect in your guitar
sound, as though you were playing in a large hall. A little can go a long way in adding that special depth to
your sound. If engaged, the reverb is always active in either overdrive or clean mode.
11) MASTER - This is the master volume control. It allows you to control the overall listening level of
both channels.
12) CD/MP3 INPUT - This is a line level 1/4" (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player
may be connected.
13) EFX SEND - This amplier is equipped with an effects loop which allows you to plug effects between
the preamp and the power amp. The EFX SEND jack is a line level 1/4” (Ø 6.3 mm) output jack into which
you may connect one or several outboard effects, eg Flanger, Delay, Chorus etc. The EFX SEND should be
connected to the input jack of the rst effect in your chain.
14) EFX RETURN - This is a line level 1/4" (Ø 6.3 mm) input jack into which you should connect the
output jack of the last effect in your chain. The effects loop may also be used with a multi-effects rack
system, or with a single effect.
15) FOOTSWITCH - This is a 1/4" (Ø 6.3 mm) input jack into which you may connect a footswitch (not
included) which will enable you to switch between the Clean and Overdrive channels while playing.
16) BALANCED OUT - This front panel XLR socket drives a post E.Q, post effects, balanced output signal
for connecting directly to one of the Balanced Microphone inputs of a mixing console.
17) POWER LED - When this red LED is lit, the amplier is ready to work. When it is off, it means the
amplier is powered off.
Features and Specications are subject to change without notice.
2 3
USER MANUALUSER MANUAL 250 GARH - 250 GAR212 250 GARH - 250 GAR212
BACK PANEL
WARNING
This amplier must be earthed. Please check that the supply voltage details given on the rear panel are in
accordance with your electricity supply.
1 POWER SWITCH - This switch turns the amplier on or off.
2 POWER FUSE - In the event of the power fuse having to be replaced, rst unplug the power cable from
the mains outlet. Then remove the fuse cover and replace the power fuse with one of the same type and
value. Never plug the power cable back into the mains outlet without the fuse cover. When powering on
the amplier, if the power fuse blows up again, go to a suitable service centre for repair.
3 MAINS INPUT - This is the input socket into which the mains power cable must be connected. This
amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are
not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can handle the
power required for this amplier.
4 VOLTAGE SELECT - This switch selects the chosen voltage level between 110-120VAC and 220240VAC as appropriate. This switch may be accessed by unscrewing the safety cover. Always make sure
that the selected voltage level is in accordance with your electricity supply.
5 SPEAKER OUT - The 250 GARH head features two external speaker sockets to connect one (or two)
external Speaker Cabinet(s) providing the total load impedance is not lower than 4 Ohms, while the 250
GAR212 combo allows you to plug one external Speaker Cabinet only with a minimum load impedance of 8
Ohms, i.e: Stagg 150 GC412 (right model) and Stagg 150 GC412A (angled model), 150W RMS/8Ω Speaker
Cabinets for guitar amplier.
1 2 5 6 7 8 9
10 11 12 13 14 15 16 17
3 4
STAGG 250 GARH & STAGG 250 GAR212 STAGG 250 GARH & STAGG 250 GAR212
1 2 4 5 5 53
250 GARH 250 GAR212
TECHNICAL SPECIFICATIONS 250 GARH EU+UK 250 GAR212EU+UK
Description
250W RMS Guitar Amp Head
w/ Spring Reverb
250W Guitar Combo w/ Spring Reverb
and 2x 12” speakers
Max. Rated Power 250 Watts RMS @ 4 Ohms 250 Watts RMS @ 4 Ohms
Speakers (N * Ø/ P/ Z) 2 x 12"/ 80W/ 16 Ohms
External Speaker Out 2 x SPK 1 x SPK
Minimum Load 4 Ohms 8 Ohms
Frequency Response 60 Hz to 20 kHz 60 Hz to 20 kHz
Total Harmonic Distortion 0.5% (Clean Mode) 0.5% (Clean Mode)
Signal to Noise Ratio - 75 dB @ max Rated Power - 75 dB @ max Rated Power
Input Impedance 220k Ohms 220k Ohms
Power Consumption 600 Watts max 600 Watts max
Maximum Input Level 45 mV RMS 45 mV RMS
Maximum Gain 42 dB @ 1 kHz 42 dB @ 1 kHz
Dimensions (H x L x P) 23 x 73 x 31 cm 63 x 73.5 x 31 cm w/o casters
Dimensions (H x W x D) 9 x 28.7 x 12.2 in 24.8 x 28.9 x 12.2 in w/o casters
Weight 22.2 kg/ 48.9 lb 44.3 kg/ 97.7 lb
RoHS
compliant
4
USER MANUAL
250 GARH - 250 GAR212
INSTRUCTIONS FOR USE
Plug the mains lead into a suitable power socket and connect your instrument to the input socket of the
amplier with a suitable guitar lead (this lead is not supplied with the amplier, but is normally supplied
with the electric guitar). Finally, press the Power Switch to the ON position, the power switch will light up
and your amplier is ready for use.
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNING.
• If, after you have followed the instructions outlined above, your amplier fails to function, please contact
your dealer. Under no circumstances should the amplier be opened. Leave all servicing to qualied
personnel.
• Electrical appliances must never be used in conditions of high humidity or heat.
To prevent any risk of re or electric shock, never spill or splash liquids on the amplier.
Should this happen, unplug the power cable from the mains outlet immediately.
• We would like to draw your intention to the instructions printed on the notice attached to the back of
the amplier.
• Exposure to extremely high sound pressure levels may cause permanent hearing damage.
Please use this amplier responsibly for you and your neighbourhood.
MARKING & CONFORMITY
1. The CE mark on this product means it conforms to the EMC Directive (2004/108/EC), CE marking
Directive (93/68/EEC) and Low Voltage Directive (2006/95/EC).
2. The “Crossed-out Wheeled Bin” is to draw your attention to the WEEE (Waste Electric & Electronic
Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately for recycling.
3. “RoHS compliant” means this device conforms to the Directive (2002/95/EC) on the restriction of the use
of certain hazardous substances in electrical and electronic equipments, such as: Mercury, Lead, Cadmium,
Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated Diphenyl Esthers (PBDE).
DISTRIBUTOR/DEALER
EMD Music 01-2009-UK
USER MANUAL
AMPLIFIER HEAd - 250 GARH EU+UK
COMbO AMPLIFIER - 250 GAR212 EU+UK
ELECTRIC bACKLINE SERIES
GUITAR AMPLIFIER w/SPRING REvERb
UK
Loading...