BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1 POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable
from the mains outlet. Then remove the fuse cover and replace the power fuse with one of the same type
and value. Never plug the power cable back into the mains outlet without the fuse cover. When powering
on the amplier, if the power fuse blows up again, go to a suitable service centre for repair.
MAINS CABLE: This amplier features a power cable with a moulded-on plug. If the socket outlets in the
home are not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can
handle the power required for this amplier. In case the power cable or plug is damaged, unplug it in a
safe way from the mains outlet and go to a suitable service centre for replacement.
Features and Specications are subject to change without notice.
FRONT PANEL:
1. INPUT: Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2. (Overdrive) GAIN: This control determines the distortion intensity of the amplier’s overdrive setting.
Adding GAIN will make your guitar sound more distorted.
3. (Overdrive) SWITCH: This switch activates the amplier ’s built-in overdrive function, which adds
distortion to the signal.
4. (Clean) VOLUME: This control determines the amplier’s overall output volume.
5. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
6. MID: This control determines the level of middle frequencies in the output signal. Adding MID will make
your guitar sound rounder and fuller. As this control is PARAMETRIC, it also allows you to vary the central
frequency of the midrange. When turned to the left, it will add low-mid and cut upper-mid. As you turn the
control to the right, you will increase the upper-mid presence, while cutting the low.
7. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
8. DIGITAL REVERB: This is the reverb intensity control. This controls the amount of reverb that is added
back to the original dry signal. Adding DIGITAL REVERB will produce a reverberation effect in your guitar
sound, as though you were playing in a large hall. A little can go a long way in adding that special depth to
your sound. If engaged, the reverb is always active in either overdrive or clean mode.
9. CD/MP3 INPUT: This is a line level 1/4” (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player
may be connected.
10. PHONES: This is a 1/4” (Ø 6.3 mm) standard jack output to connect the headphones. When
headphones are connected, no sound is produced from the speaker.
11. POWER LED: When this red LED is lit, the amplier is ready to work. When i t is off, it means the
amplier is powered off.
12. POWER: This switch turns the amplier on or off.
CM
C US
L
I
S
D
T
E
E
R
T
E
T
K
N
I
CONFORM S TO
UL STD. 6006 5
CERTIFI ED TO
CAN/CSA ST D.
C22.2 No. 60065: 03
DATE
2 3
USER’S MANUALSUSER’S MANUAL 15 GA DR USA 15 GA DR USA
1
1 2 3 4 5 6 7 8 12109 11
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker 15 Watts RMS @ 8 Ohms load / 6.5” speaker
Frequency Response 80 Hz to 15 kHz
Total Harmonic Distortion 0.8% (Clean Mode)
Signal to Noise Ratio - 55 dB @ max Rated Power
Input Impedance
220k Ohms
Power Consumption
25 Watts max
Maximum Input Level
45 mV (RMS)
Maximum Gain
42 dB (@ 1kHz)
Dimensions (H x W x D)
31 x 35 x 19 cm / 12.2 x 13.8 x 7.5 in.
Weight
6.3 kg / 13.9 lbs
4
USER’S MANUAL
15 GA DR USA
RoHS
compliant
INSTRUCTIONS FOR USE:
Plug the mains lead into a suitable power socket and connect your instrument to the input socket of the
amplier with a suitable guitar lead (this lead is not supplied with the amplier, but is normally supplied
with the electric guitar). Finally, press the Power Switch to the ON position, the power LED will glow and
your amplier is ready for use.
IMPORTANT SAFETY INSTRUCTIONS:
1• Read all instructions carefully
2• Keep this instruction manual for future reference
3• Please follow all instructions and heed all precautions as stated
4• Do not use this apparatus on or near water
5• Always use a polarized, grounded plug as supplied. A grounded plug has two blades and a third grounding
prong. The wide blade, or third prong, is provided for your safety. Do not compromise the integrity of its safety
purpose by altering or modify this plug in any way. If the provided plug does not t into your mains outlet,
consult a qualied electrician for replacement of the obsolete outlet.
6• Protect the power cable from being walked on, particularly at the mains socket or at the point of connection
to the apparatus.
7• Only use attachments or accessories that are specied by the manufacturer.
8• Always unplug the device when leaving it unused for an extended period of time, or in the event of a
thunderstorm.
9• Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, particularly the plug or power cable, liquids spilled or foreign objects dropped into the apparatus, or
if the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
10• The apparatus should be connected to a mains socket outlet with a protective earthing connection.
11• The mains plug is used to connect or disconnect the device. By maintaining the apparatus connected to the
mains, it shall remain readily operational.
MARKING & CONFORMITY:
1. The «C (ETL) US» mark on this product means it conforms to the safety and performance standards
(UL 60065 and CSA C22.2 No.60065:03) accepted throughout the United States and Canada.
2. The «Crossed-out Wheeled Bin» is to draw your attention to the WEEE (Waste Electric & Electronic
Equipment) Directive (2002/96/EC). It means this apparatus should be collected separately for recycling.
3. «RoHS compliant» means this device conforms to the Directive (2002/95EC) on the restriction of the use
of certain hazardous substances in electrical and electronic equipments, such as: Mercury, Lead, Cadmium,
Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated Diphenyl Esthers (PBDE).
DISTRIBUTOR/DEALER
EMD MUSIC 01-2008-USA
USER’S MANUAL
GUITAR AMPLIFIER
wITH DIGITAL REvERB - 15 GA DR USA
Loading...