Stafer 594.T.X5.00, 594.T.X1.00 User Manual

433,42 MHz

User manual for :

594.T.X1.00

594.T.X5.00

www.stafer.com

Dear Customer, thank you for purchasing a STAFER S.p.A. product. This guide contains all the information you will need concerning the use of this product. Read the instructions carefully and keep them for further consultation. The transmitter is designed specifically to control sun awnings, blinds, roller shutters, screens or similar items. All other use beyond the field defined by STAFER S.p.A. is forbidden. This, as well as the breach of the instructions given in this guide, shall release STAFER S.p.A. from any liability and shall annul the product warranty. Water, humidity, heat sources, accidental falls can damage the device. Do not use abrasive products or solvents to clean the product.

Table of contents

Technical specifications Package contents Battery insertion/replacement Fixing the wall bracket Disposal

Notes on radio systems Warnings for safety Warnings for the installation Warnings for use

1. Functions associated with the transmitter buttons.

2. Enabling/disabling groups and channels.

3. Delay associated to the sequencer channel.

4. Receiver menu

4A. Modification of Function 01 - WIND THRESHOLD 4B. Modification of Function 02 - SUN THRESHOLD 4C. Modification of Function 07- WORKING TIME 4D. Modification of Function 08 - «AIR CHANGE» FUNCTION 4E. Modification of Function 11- FABRIC RELEASE 4F. Modification of Function 12 - ORIENTATION TIME 4G. Modification of Function 16 - ANEMOMETRIC TEST 4H. Modification of Function 17 - RADIO TEST 4I. Modification of Function 18 - BUTTONS LOGIC 4L. Function 29 - RECEIVER RESET

PROG

WARNINGS FOR USE

ü The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they are supervised or given instructions on how to use the product by a person responsible for their safety.

ü Before operating the roller shutter/awning, make sure there are no people or objects in the area involved in its movement. Check the automation during

movement and keep people at a safe distance, until the movement ends.

ü Do not allow children to play with the appliance or with the fixed control devices. Also, keep the portable control devices (remote controls) out of the reach of

children.

ü Do not operate the roller shutter/awning when maintenance operations are being carried out (e.g. window cleaning). If the control device is automatic,

disconnect the motor from the power line.

1. FUNCTIONS ASSOCIATED WITH THE TRANSMITTER BUTTONS

Basic functions

stop

down

channel prev

Intermediate position (third limit switch)

Bring motor in a desired position.

Press simultaneously STOP and THIRD LIMIT SWITCH until the motor moves (about 5 seconds).

channel next

To store:

Special functions

right orientation

sun function

third switch

left orientation

Programming function

Access to the receiver menu

PROG

transmitters

insertion-cancellation

To recall:

Technical specifications

- Power supply: n° 1 battey CR2032

- Dimensions: 46x147x16 mm

- Weight: 50 gr

- Working temperature: from 0 to +55°C

Package contents

- 1 transmitter

ARCO5 - ARCO10 - ARCO20

- 1 battery CR2032

- 1 wall bracket

- 2 dowels + 2 screws

- 1 instruction guide

Battery insertion/replacement

The transmitter is powered by a battery C R2032. To insert the battery, remove the battery cover on the back of the transmitter, insert the battery respecting the polarity, close the cover. Use of batteries different than those referred can cause an explosion hazard. Used batteries must be discarded in appropriate containers. It it recommended to replace the battery every 2 years.

Fixing the wall bracket

Using a screw driver, remove the central cover from the bracket. Fix the bracket to the wall using the supplied plugs (distance between holes 45 mm). Place the cover back on.

- Radio frequency: 433.42 Mhz

- Radio channel for 594.T.X1.00: 1

- Radio channels for 594.T.X5.00: 10 + sequencer channel

Disposal

At the end of the product life cycle, d ispo s e o f th e d e vice i n compliance with local regulations. Th is pr oduct could con ta in substances that are harmful to h u m a n h e a l t h a n d t h e environment: do not dispose of the product in domestic waste.

Notes on radio systems

Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals). It is in any case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible sources of interference. Radio systems can be used where any disturbances or malfunction of the transmitter or receiver do not constitute a risk factor, or if such factor is eliminated using appropriate safety systems. The presence of radio devices working at the same transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the range of the system, limiting functionality.

Warnings For Safety

ü Keep these instructions for future maintenance work and disposal of the product. ü All the product installation, connection, programming and maintenance operations must be carried out only by a qualified and skilled technician, who must

comply with laws, provisions, local regulations and the instructions given in this manual.

Warnings for the installation

ü Read the technical data in "Technical Specifications" to assess the limits of use of the product. ü Check that the package is intact and has not been damaged in transit. ü Make sure that the packaging is intact and has not been damaged during transportation. ü A heavy knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor. ü Do not modify or replace parts without the manufacturer's permission. ü Non utilizzare prodotti abrasivi né solventi per la pulizia del prodotto; non pulire utilizzando pulitori a getto d'acqua o ad alta pressione.

LOOK OUT! With the shutter type «ADJUSTABLE SLATS» THIRD SWITCH corresponds to shutter down with the slats completely closed. Pressing instead DOWN button the shutter closes and the slats are open.

Sun/automatic lowering function (with wind-sun or wind sensor)

Select the channel (excluded «SE» sequencer channel)

Press SUN until the state of the YELLOW LED varies (about 2 seconds)

YELLOW LED LIGHT ON/OFF: «sun/automatic lowering» function active / off

With a wind-sun sensor this function active the sun function. With a wind sensor this function active «automatic lowering» of awning when the wind alarm is ended.

For clarifications, consult the manual of your wind-sun sensor.

Notes:

- It is possible that some receiving devices do not associate any operations to some transmitter buttons.

- It is possible that some receiving devices associate to the transmitter buttons some operations different from what it is described. In this case consider the instruction manual of the receiving device.

2. ENABLING/DISABLING CHANNELWS FOR 594.T.X5.00 (TO HYDE ON DISPLAY)

Press STOP and then MENU and hold the buttons for about 3 seconds, until the ch symbol is

displayed.

Press STOP to modify the setting.

recycled paper

B C

Press STOP. 01 will appear on display.

E F

If necessary, select another channel/group and return to point C.

if RED LED IS ON: channel disabled.

To exit, press twice MENU or

wait about 15 seconds (the display switches off).

if YELLOW LED IS ON: channel enabled.

versione 1.0

3. DELAY ASSOCIATED TO THE SEQUENCER CHANNEL (only 594.T.X.00)

The «10 channels transmitter» have a virtual channel called sequencer «SE», which send the selected command in succession for all the active radio channels. To select the Sequencer, scroll the list of channels until SE symbol appears. It is possible to set the interval (from 1 to 10 sec) of time which must pass between the transmission on one channel and the next. The factory sets the delay at 1 second. The use of high intervals of time can negatively effect on the battery life. To modify the setting:

Press STOP and then MENU and hold the buttons for about 3 seconds, until the symbol ch is

displayed.

Use PREV and NEXT to set the required value.

Press NEXT. The Sd symbol appears on the display.

Press STOP to save the setting.

Press STOP. The currently set value appears on the display (from 01 to 10 sec).

To exit, press twice MENU or

wait about 15 seconds (the display switches off).

4. RECEIVER MENU

After storing a radio channel of the transmitter on a receiver, it is possible to modify some operating parameters of the receiver directly from the transmitter. To identify the editable settings, refer to the instruction manual of the receiving device. To modify an operating parameter:

Select the channel associated to the receiver.

Press MENU on the transmitter for

about 5 seconds, until rS symbol appears.

Use PREV and NEXT to select the code of the parameter to edit (see table).

4.C - Modification of Function 07 - WORKING TIME (only for 594.R.EN.00)

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 7 times NEXT. 07 appears on the display.

04. Press 1 time STOP. The receiver signals the current value. Example: if it gets up for sec. = 2: p 2 ( 2 short upward movements) if it gets up for sec. = 35: p 3 - pause - p 5 if it gets up for sec. = 120: p 1 pause p 2 pause p 1long

05. Using PREV and NEXT to set the new value: for time = 3: 0 time PREV and 3 times NEXT (the value must be between 5 and 240. Factory set is 120sec.)

06. Press 1 time STOP. The receiver signal the new value.

4.D - Modification of Function 08 - AIR CHANGE (only for 594REN00)

Since the factory is set at 1 (NOT active). Possible values from 1 to 6.

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 8 times NEXT. 08 appears on the display.

04. Press 1 time STOP. The receiver signals the current value Example: if time = 2 sec: p 2 (2 short upward movements) if time = 5 sec: p 5 (5 short upward movements)

05. Using PREV and NEXT to set the new value: for time 3 sec: 0 times PREV and 3 times NEXT for time 6 sec: 1 time PREV and 6 times NEXT

4.E - Modification of Function 11 - FABRIC RELEASE

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 time PREV and 1 time NEXT. 11 appears on the display.

04. Press 1 time STOP. The receiver signals the current value. Example: if parameter value = 2: p 2 (2 short upward movements)

05. Using PREV and NEXT to set the new value (from 1 at 5. 1 is function OFF. From factory is set 1) Example: for parameter = 2; (0 time PREV) - 2 times NEXT

06. Press 1 time STOP.The receiver signal the new value.

06. Press 1 time STOP. The receiver signal the new value.

To call the function, press the button «THIRD SWITCH»..

Press STOP. The receiver will show the current value of the parameter.

Use PREV and NEXT to set the new parameter value.

RECEIVER CODE FUNCTIONS

Press STOP. The receiving device shows the new value of the parameter.

01 - wind theshold 02 - sun threshold 07 - working time 08 - «air change» function

It is possible to exit the «receiver menu» at any time by pressing the button MENU briefly.

11 - fabric release 12 - orientation time 16 - anemometric test 17 - radio test 18 - buttons logic

29 - receiver reset

On the next section, the operations to be performed to modify the parameters are described.

CONVENTIONS USED IN THE EXAMPLES:

Ÿ On the following example with p is indicated a short upward movement (example: p 3 = 3 short upward movements of the motor). Ÿ On the following example with q is indicated a short downward movement (example: q 1 = 1 short downward movement of the motor). Ÿ Some receiver may display the settings in another way (i.e. not with motor movements, but with visual and acoustic signals) or not display the settings. In

these cases, refer to the instruction manual of the receiver.

4.A - Modification of Function 01 - WIND THRESHOLD

It’s NOT possible for sensor 593.K.XB.00 (in this case you can modify only by buttons on sensor). With 593.K.XS.00 is necessary a «10 channels» transmitter.

4.B - Modification of Function 02 - SUN THRESHOLD

It’s NOT possible for sensor 593.K.XB.00 (in this case you can modify only by buttons on sensor). With 593.K.XS.00 is necessary a «10 channels» transmitter. You must before active the «sun function» on transmitter on motor

01. Select the correct radio channel and bring the motor on the

channel (read the section number 1 of this manual).

intermediate position.

02. If you have 593KXS00 you must store the sun-wind sensor in a free channel of transmitter (read manual of sun-wind sensor at the section 6) and select this channel.

03. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 time NEXT. 01 appears on the display.

04. Press 1 time STOP.The receiver signal the new value. Examples: if threshold = 08 Km/h: p 8 (8 short movements) if threshold = 15 Km/h: p 1 - pause - p 5 if threshold = 30 Km/h: p 3 - pause - p 1 long

01. Select the correct radio channel and bring the motor on the intermediate position.

02. If you have 593KXS00 you must store the sun-wind sensor in a free channel of transmitter (read manual of sun-wind sensor at the section 6) and select this channel.

03. Press MENU for about 5 seconds. rS appears on the display.

04. Press 2 times NEXT. 02 appears on the display.

04. Press 1 time STOP. The receiver signals the current value Examples: if threshold = 07 Klux: p 7 (7 short movements) if threshold = 18 Klux: p 1 - pause - p 8

05. Using PREV and NEXT to set the new value. (from 5 Km/h at 35

if threshold = 20 Klux: p 2 - pause - p 1 long Km/h. From factory set to 15 Km/h). Examples: for threshold 08 Km/h: (0 time PREV) - 8 times NEXT for threshold 15 Km/h: 1 time PREV - 5 times NEXT for threshold 30 Km/h: 3 times PREV - (0 time NEXT)

06. Using PREV and NEXT to set the new value (from 1 Klux at 45

Klux. From factory set to 16 Klux).

Examples:

for threshold 07 Klux: (0 time PREV) - 7 times NEXT

for threshold 18 Klux: 1 time PREV - 8 times NEXT

07. Press 1 time STOP.The receiver signal the new value.

for threshold 20 Klux: 2 times PREV - (0 time NEXT)

07. Press 1 time STOP.The receiver signal the new value.

4.F - Modification of Function 12 - ORIENTATION TIME

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 time PREV and 2 times NEXT. 12 appears on the display.

04. Press 1 time STOP. The receiver signals the current value. Example: if parameter value = 4: p 4 (4 short upward movements)

4.G - Modification of Function 16 - ANEMOMETRIC TEST

Only available with 593.K.RS.00 and 593.K.RA.00.

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 TIME PREV and 6 times NEXT. 16 appears on the display.

04. Press 1 time STOP. The receiver signals the current value. Function active: p 1 (1 short upward movement)

05. Using PREV and NEXT to set the new value (from 1 to 5. 1 is function OFF. From factory is set 1). Example: for parameter = 4; (0 time PREV) - 4 times NEXT

Function not active: q 1 (1 short descent movement)

05. Press PREV to disable the function (Of appears on the display) or NEXT to enable the function (On appears on the display). Factory set is Of.

06. Press 1 time STOP. The receiver signal the new value.

Function active: p 1 - Function not active: q 1

4.H - Modification of Function 17 - RADIO TEST

Only available with 593.K.XS.00 and 593.K.XB.00.

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 TIME PREV and 7 times NEXT. 17 appears on the display.

04. Press 1 time STOP. The receiver signals the current value.

Function active: p 1 (1 short upward movement) Function not active: q 1 (1 short descent movement)

05. Press PREV to disable the function (Of appears on the display) or NEXT to enable the function (On appears on the display). Factory set is On.

06. Press 1 time STOP. The receiver signal the new value.

Function active: p 1 - Function not active: q 1

4.I - Modification of Function 18 - BUTTONS LOGIC

01. Select the correct radio channel and bring the motor on the intermediate position.

02. Press MENU for about 5 seconds. rS appears on the display.

03. Press 1 time PREV and 8 times NEXT. 18 appears on the display

04. Press 1 time STOP. The receiver signals the current value.

Hold to run: p 1 (1 short upward movement) Pulse: q 1 (1 short descent movement)

05. Press PREV for logic «pulse» (Of appears on the display) or NEXT for logic «hold to run» (On appears on the display). Factory set is Of.

06. Press 1 time STOP. The receiver signal the new value.

Hold to run: p 1 - Pulse: q 1

4.L - Function 29 - RECEIVER RESET

WARNING:

For this procedure, use ONLY A CHANNEL STORED ON THE RECEIVER THAT YOU WANT TO RESET if more devices are tuned on the same channel, power on only the device to be resetted.

01. Select the channel tuned on the receiver to be «resetted».

02. Press MENU for around 5 seconds. rS appears on the display.

03. Press 2 times PREV and 9 times NEXT. 29 appears on the display.

04. Press 1 time STOP. The receiver signals that it is ready for the memory reset (with visual or acoustic signals, see the receiver instruction manual); on

the transmitter, all the leds and display segments come on intermittently for a few seconds.

Then they light on.

05. until the receiver signals that the factory settings have been restored. Press together PREV and NEXT

06. Follow the instruction manual of the receiver to re-install the receiver.

All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by STAFER, the device must be used exclusively with transmitters produced by STAFER. STAFER cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.

Stafer 594.T.X5.00, 594.T.X1.00 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual