X-NUCLEO-OUT08A1 Bill of materials version 1 | sheet 1
Table 1: X-NUCLEO-OUT08A1 bill of materials
Item Q.ty Ref. Part/Value Description Manufacturer Order code
1 2 C1, C2 4700 pF Capacitors
2 1 C3 2.2 µF Capacitor AVX 12061C225KAT2A
3 1 C4 100 nF Capacitor
4 1 C5 10 nF Capacitor
5 1 C6 47 nF Capacitor
6 1 C7 0.1 µF Capacitor Kemet C0603C104K5RACTU
7 1 C8 47 µF Capacitor
8 1 CN1 Con3
9 1 CN2 Con2
10 1 CN5
11 2 CN6, CN9
SSQ-110-04-FS
SSQ-108-04-FS
Fixed terminal
block
Fixed terminal
block
Connector Samtec Inc. SSQ-110-04-F-S
Connectors Samtec Inc. SSQ-108-04-F-S
Vishay
Vitramon
Wurth
Electronics Inc.
Murata
Electronics
North America
Murata
Electronics
North America
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
HV1825Y472KXHATHV
885012207128
GRM188R71H103KA01D
GCM188R71H473KA55D
860040875002
691214110003
691214110002
12 2 CN7, CN10
13 1 CN8
14 2 D1, D7 STPS1H100A
15 1 D2 BAT48 (N.M.)
16 1 D3 BAT41ZFILM
17 1 D5 150060RS75000 LED
18 1 D6 150060VS75000 LED
19 1 D8 TDZ6V2,J115 Zener diode
SSQ-119-04-LD (N.M.)
SSQ-106-04-FS
Connectors Samtec Inc. SSQ-119-04-L-D
Connector Samtec Inc. SSQ-106-04-F-S
100 V, 1 A
power Schottky
rectifier
40 V, 350 mA
axial general
purpose signal
Schottky diode
100 V, 200 mA
surface mount
general purpose
signal Schottky
diode
ST STPS1H100A
ST BAT48JFILM
ST BAT41ZFILM
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Nexperia USA
Inc.
150060RS75000
150060VS75000
TDZ6V2,J115
20 4
21 8
22 2 J13, J14
All information on this page is subject to the Evaluation Board License Agreement included in this document Page 1 of 5
ISO1 ISO2
ISO3 ISO4
J1, J2, J3, J4,
J5, J7, J8, J9
ACPL-217-50AE Optocouplers Broadcom Ltd. ACPL-217-50AE
Strip 2x1 pitch
2.54 mm., con2strip-male
con8-2x4-stripmale pitch 2.54mmConnectors Amphenol ICC 67996-408HLF
Jumpers
Sullins
Connector
Solutions
STC02SYAN
X-NUCLEO-OUT08A1 Bill of materials version 1 | sheet 2
Item Q.ty Ref. Part/Value Description Manufacturer Order code
N-channel
100 V, 0.23
23 1 Q1 STN2NF10
24 2 R1, R2 27 K Resistors Yageo RC0603FR-0727KL
25 2 R3, R4 2.2 K Resistors Yageo RC0603FR-072K2L
26 2 R5, R6 390 Resistors Yageo RC0603FR-07390RL
27 2 R7, R8 15 k Resistors Yageo RC0603FR-0715KL
28 2 R9 R10 6.8 k Resistors Yageo RC0603FR-076K8L
29 1 R11 1 k Resistor Yageo RC0603FR-071KL
30 3 R12, R13, R14 22 k Resistors Yageo RC0603FR-0722KL
1 R15 68 k Resistor Yageo RC0603FR-0768KL
32 1 R16 10 k Resistor Yageo RC0603FR-0710KL
Ohm, 2.4 A
STripFET(TM) II
power MOSFET
ST STN2NF10
33 4
34 12
35 2 SW1, SW2 con3-strip-male Switches Any Any
36 5
37 1 TR3 SM15T10AY
38 1 U1 IPS160HF
39 1 U2 SM15T39CA
40 1 U3
R101, R102,
R103, R104
R111, R112,
R121, R122,
R123, R124,
R125, R130,
R131, R132,
R133, R134
TP3, TP6, TP7,
TP8, TP9
100 k Resistors Yageo RC0603FR-07100RP
100 k (N.M.) Resistors Yageo RC0603FR-07100RP
5001 Test points
Automotive
1500 W TVS in
SMC
Single high-side
switch
1500 W, TVS in
SMC
High-power
ESDA15P60-1U1M
(N.M.)
transient
voltage
suppressor
(TVS)
Keystone
Electronics
ST SM15T10AY
ST IPS160HF
ST SM15T39CA
ST ESDA15P60-1U1M
5001
All information on this page is subject to the Evaluation Board License Agreement included in this document Page 2 of 5
X-NUCLEO-OUT08A1 Evaluation Board License Agreement
STMicroelectronics
EVALUATION BOARD LICENSE AGREEMENT
By using this evaluation board or kit (together with all related software, firmware, components, and documentation provided by
ST, “Evaluation Board”), You (“You”) are agreeing to be bound by the terms and conditions of this Evaluation Board License
Agreement (“Agreement”). Do not use the Evaluation Board until You have read and agreed to this Agreement. Your use of the
Evaluation Board constitutes Your acceptance of this Agreement.
LICENSE
STMicroelectronics (“ST”) grants You the right to use the enclosed Evaluation Board offering limited features only to evaluate
and test ST products solely for Your evaluation and testing purposes in a research and development setting. The Evaluation
Board shall not be, in any case, directly or indirectly assembled as a part in any production of Yours as it is solely developed to
serve evaluation purposes and has no direct function and is not a finished product. If software and/or firmware is accompanied
by a separate end user license agreement (“EULA”), then such software and/or firmware shall be governed by such EULA.
EVALUATION BOARD STATUS
The Evaluation Board offers limited features allowing You only to evaluate and test the ST products. The Evaluation Board is
not intended for consumer or household use. You are not authorized to use the Evaluation Board in any production system,
and it may not be offered for sale or lease, or sold, leased or otherwise distributed for commercial purposes. If the Evaluation
Board is incorporated in an evaluation system, the evaluation system may be used by You solely for Your evaluation and testing
purposes. Such evaluation system may not be offered for sale or lease or sold, leased or otherwise distributed for commercial
purposes and must be accompanied by a conspicuous notice as follows: “This device is not, and may not be, offered for sale or
lease, or sold or leased or otherwise distributed for commercial purposes”.
OWNERSHIP AND COPYRIGHT
Title to the Evaluation Board remains with ST and/or its licensors. You may not remove any copyright or other proprietary rights
notices without prior written authorization from ST. You may make one copy of the software and/or firmware of the Evaluation
Board for back up or archival purposes provided that You reproduce and apply to such copy any copyright or other proprietary
rights notices included on or embedded in the software and/or firmware. You agree to prevent any unauthorized copying in
whole or in part of the Evaluation Board.
RESTRICTIONS AND WARNINGS
Before You handle or use the Evaluation Board, You must carefully review any related documentation provided by ST. Such
documentation may contain important warnings. You shall comply with all such warnings and other instructions and employ
reasonable safety precautions in using the Evaluation Board. Failure to do so may result in death, personal injury, or property
damage. If You have any questions regarding the safe usage of the Evaluation Board, You should contact ST for guidance.
You may not sell, assign, sublicense, lease, rent or otherwise distribute the Evaluation Board for commercial purposes, in whole
or in part, or use Evaluation Board in a production system, with the exception that if You are an authorized ST distributor, You
may resell the Evaluation Board in compliance with the applicable terms and conditions. Except as provided in this Agreement
or as explicitly permitted in the documentation of the Evaluation Board, You may not reproduce the Evaluation Board or modify,
reverse engineer, de-compile or disassemble its software and/or firmware, in whole or in part.
You shall not use the Evaluation Board in any safety critical or functional safety testing, including but not limited to testing of life
supporting, military or nuclear applications. ST expressly disclaims any responsibility for such usage which shall be made at
Your sole risk, even if ST has been informed in writing of such usage. Unless expressly designated in writing by ST as suitable
for use in testing automotive or aerospace applications, You shall not use the Evaluation Board in such testing.
Notice applicable to Evaluation Boards according to European Regulation
For the European Regulation of the Evaluation Board, the applicable EU directives are considered, with a particular attention
to the Low Voltage Directive (LVD) 2014/35/EU, the Electromagnetic Compatibility (EMC) Directive 2014/30/EU, and the Radio
Equipment Directive (RED) 2014/53/EU. If the Evaluation Board is outside the scope of the foregoing Directives, then the
General Product Safety Directive (GPSD) 2001/95/EC and Council Directive 93/68/EEC, amending Directive 73/23/EEC on
electrical equipment designed for use within certain voltage limits, are applicable.
The Evaluation Board meets the requirements of the Restriction of Hazardous Substances (RoHS 2 or RoHS recast) Directive
2011/65/EU, Annex II, as amended by Directive 2015/863/EU.
Notice applicable to Evaluation Boards not FCC-Approved
This kit is designed to allow:
(1)Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to
incorporate such items in a finished product and
(2)Software developers to write software applications for use with the end product.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC
equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference
to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate
under part 15, part 18 or part 95 of 47 CFR, Chapter I (“FCC Rules”), the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
Page 3 of 5
X-NUCLEO-OUT08A1 Evaluation Board License Agreement
For Evaluation Boards annotated as FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 Compliant
• FCC Interference Statement for Class A Evaluation Boards: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
• FCC Interference Statement for Class B Evaluation Boards: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
◦
Increase the separation between the equipment and receiver.
◦
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
◦
Consult the dealer or an experienced radio/TV technician for help.
◦
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
WARRANTY
ST WARRANTS THAT IT HAS THE RIGHT TO PROVIDE THE EVALUATION BOARD TO YOU. THIS WARRANTY IS
PROVIDED BY ST IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, STATUTORY, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTY AS TO MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR ANY PARTICULAR
PURPOSE, OR UNINTERRUPTED OR ERROR-FREE OPERATION, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. THE
EVALUATION BOARD IS PROVIDED “AS IS”.
YOU WARRANT TO ST THAT YOU WILL ENSURE THE EVALUATION BOARD IS USED ONLY BY ELECTRONICS
EXPERTS WHO UNDERSTAND THE DANGERS OF HANDLING AND USING SUCH ITEMS, YOU ASSUME ALL
RESPONSIBILITY AND LIABILITY FOR ANY IMPROPER OR UNSAFE HANDLING OR USE OF THE EVALUATION BOARD
BY YOU, YOUR EMPLOYEES, AFFILIATES, CONTRACTORS, AND DESIGNEES.
LIMITATION OF LIABILITIES
IN NO EVENT SHALL ST BE LIABLE TO YOU, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY, OR ANY OTHER LEGAL THEORY, FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL, PUNITIVE,
OR EXEMPLARY DAMAGES WITH RESPECT TO ANY MATTERS RELATING TO THIS AGREEMENT, REGARDLESS OF
WHETHER ST HAS BEEN ADVISED OF THE POSSIBILITY OF THE SAME. IN NO EVENT SHALL ST’S LIABILITY ARISING
OUT OF THIS AGREEMENT IN THE AGGREGATE EXCEED THE AMOUNT PAID BY YOU UNDER THIS AGREEMENT FOR
THE PURCHASE OF THE EVALUATION BOARD, OR TEN UNITED STATES DOLLARS ($10.00) IF NO PURCHASE PRICE
WAS PAID.
INDEMNIFICATION
You shall, at Your expense, defend ST and its Affiliates against a claim or action brought by a third party for infringement
or misappropriation of any patent, copyright, trade secret or other intellectual property right of a third party to the extent
resulting from (1) Your combination of the Evaluation Board with any other component, system, software, or firmware, (2) Your
modification of the Evaluation Board, or (3) Your use of the Evaluation Board in a manner not permitted under this Agreement.
You shall indemnify ST and its Affiliates against and pay any resulting costs and damages finally awarded against ST or its
Affiliates or agreed to in any settlement, provided that You have sole control of the defense and settlement of the claim or
action, and ST cooperates in the defense and furnishes all related evidence under its control at Your expense. ST will be
entitled to participate in the defense of such claim or action and to employ counsel at its own expense.
“Affiliates” means any corporation or other entity directly or indirectly controlled by, controlling or under common control with the
entity in question, for so long as such ownership exists. "Control" means the direct or indirect beneficial ownership of more than
fifty (50%) percent of the stock or other equity interests entitled to vote for the election of directors or an equivalent governing
body. Any such corporation or other legal entity shall be deemed to be an Affiliate of such Party only as long as such Control
exists.
TERMINATION
ST may terminate this Agreement without notice if You breach this Agreement. Upon termination, You shall immediately destroy
or return all copies of the software, firmware, and documentation of the Evaluation Board to ST and certify in writing to ST that
You have done so.
APPLICABLE LAW AND JURISDICTION
This Agreement shall be governed, construed and enforced in accordance with the laws of Switzerland, without regard to its
conflict of laws rules. The UN Convention on Contracts for the International Sale of Goods shall not apply to this Agreement. In
case of dispute and in the absence of an amicable settlement, the only competent jurisdiction shall be the Courts of Geneva,
Switzerland. Any breach of this Agreement by You may result in irreparable damage to ST for which ST will not have an
Page 4 of 5
X-NUCLEO-OUT08A1 Evaluation Board License Agreement
adequate remedy at law. Accordingly, in addition to any other remedies and damages available, You acknowledge and agree
that ST may immediately seek enforcement of this Agreement in any jurisdiction by means of specific performance or injunction,
without any requirement to post a bond or other security.
SEVERABILITY
If any provision of this agreement is or becomes, at any time or for any reason, unenforceable or invalid, no other provision of
this agreement shall be affected thereby, and the remaining provisions of this agreement shall continue with the same force and
effect as if such unenforceable or invalid provisions had not been inserted in this Agreement. In addition, any unenforceable or
invalid provision shall be deemed replaced by a provision that is valid and enforceable and that comes closest to expressing the
intention of the unenforceable or invalid provision.
WAIVER
The waiver by either party of any breach of any provision of this Agreement shall not operate or be construed as a waiver of any
other or a subsequent breach of the same or a different provision.
RELATIONSHIP OF THE PARTIES
Nothing in this Agreement shall create, or be deemed to create, any joint venture, partnership, principal-agent, employeremployee or other relationship between the Parties, except that of independent contractors. Neither Party has the authority or
power to bind, to contract in the name of, or to create a liability for the other in any way or for any purpose.
SURVIVAL
Any provision of this Agreement which imposes an obligation after termination of this Agreement shall survive the termination of
this Agreement.
SECTION HEADINGS
Section headings are inserted for convenience only and shall not be used to interpret this Agreement.
WASTE AND RECYCLING
The Evaluation Board is not to be disposed of as urban waste. At the end of its life cycle, differentiated waste
collection must be followed. Consult the local authorities for more information on the proper disposal channels. It is
mandatory to separately collect the Evaluation Board and make sure it is delivered it to the appropriate waste management and
recycling centers.
As of 15 August 2018, in all the countries belonging to the European Union, the Evaluation Board is subject to the WEEE
Directive 2012/19/EU requirement; therefore, it is forbidden to dispose of the Evaluation Board as undifferentiated waste or with
other domestic wastes. Consult the local authorities for more information on the proper recycling centers.
Disposing of the Evaluation Board incorrectly may cause damage to the environment and may be subject to fines based on
specific countries’ rules.
Page 5 of 5
Loading...