ST VND10N06, VND10N06-1 User Manual
Features
3
VND10N06
VND10N06-1
"OMNIFET"
fully autoprotected Power MOSFET
Max on-state resistance (per ch.) R
Current limitation (typ) I
Drain-Source clamp voltage V
■ Linear current limitation
■ Thermal shutdown
■ Short circuit protection
■ Integrated clamp
■ Low current drawn from input pin
■ Logic level input threshold
■ ESD protection
■ Schmitt trigger on input
■ High noise immunity
DS(on)
lim
CLAMP
0.3Ω
10A
60V
DPAK
TO-252
3
1
IPAK
TO-251
2
1
Description
The VND10N06 and VND10N06-1 are monolithic
devices designed in STMicroelectronics VIPower
M0-2 technology, intended for replacement of
standard Power MOSFETs in DC to 50KHz
applications. Built in thermal shutdown, linear
current limitation and overvoltage clamp protect
the chip in harsh environments.
Table 1. Device summary
Order codes
Package
Tube Tape and reel
DPAK VND10N06 VND10N06TR
IPAK VND10N06-1
December 2008 Rev 3 1/25
www.st.com
25
Contents VND10N06 / VND10N06-1
Contents
1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 Protection features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Package and packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1 ECOPACK® packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 DPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3 IPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4 DPAK packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.5 IPAK packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2/25
VND10N06 / VND10N06-1 List of tables
List of tables
Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 3. Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 4. Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 5. Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 6. On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 7. Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 8. Source Drain diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 9. Protections (-40°C < Tj < 150°C, unless otherwise specified) . . . . . . . . . . . . . . . . . . . . . . . 8
Table 10. DPAK mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 11. IPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 12. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3/25
List of figures VND10N06 / VND10N06-1
List of figures
Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2. Switching waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 3. Switching time test circuit for resistive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4. Test circuit for inductive load switching and diode recovery time . . . . . . . . . . . . . . . . . . . . . 9
Figure 5. Unclamped inductive load test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6. Input charge test circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 7. Unclamped inductive waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 8. Static Drain-Source on resistance (V
Figure 9. Static Drain-Source on resistance (V
Figure 10. Derating curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 11. Static Drain-Source on resistance vs. input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 12. Current limit Vs. junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 13. Source-Drain diode voltage Vs. junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 14. Step response current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 15. Switching time resistive load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 16. Turn-on current slope (V
Figure 17. Turn-on current slope (V
= 3.5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IN
= 7V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IN
Figure 18. Input voltage Vs. input charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 19. Turn-off Drain-Source voltage slope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 20. Turn-off Drain-Source voltage slope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 21. Capacitance variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 22. Switching time resistive load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 23. Normalized on resistance Vs. temperature (V
Figure 24. Output characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 25. Normalized on resistance Vs. temperature (V
Figure 26. Normalized input threshold voltage Vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 27. Thermal impedance for DPAK / IPAK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 28. DPAK package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 29. IPAK mechanical data and package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 30. DPAK footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 31. DPAK tube shipment (no suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 32. DPAK tape and reel shipment (suffix “TR”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 33. IPAK tube shipment (no suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
= 3.5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IN
= 5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IN
= 7V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IN
= 3.5V). . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IN
4/25
VND10N06 / VND10N06-1 Block diagram and pin description
1 Block diagram and pin description
Figure 1. Block diagram
5/25
Electrical specifications VND10N06 / VND10N06-1
2 Electrical specifications
2.1 Absolute maximum ratings
Stressing the device above the rating listed in the “Absolute maximum ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to Absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
program and other relevant quality document.
Table 2. Absolute maximum ratings
Symbol Parameter Value Unit
V
V
V
Drain-Source voltage (V
DSn
Input voltage Internally clamped V
INn
I
Input current ± 20 mA
in
I
Drain current Internally limited A
Dn
I
Reverse DC output current - 15 A
Rn
Electrostatic discharge
ESD
(R = 1.5KΩ, C = 100pF)
Total dissipation at Tc = 25°C 35 W
P
tot
T
Operating junction temperature Internally limited °C
j
T
Case operating temperature Internally limited °C
c
T
Storage temperature - 55 to 150 °C
stg
2.2 Thermal data
Table 3. Thermal data
Symbol Parameter Max. value Unit
R
thj-case
R
thj-amb
Thermal resistance junction-case 3.5 °C/W
Thermal resistance junction-ambient 100 °C/W
= 0V) Internally clamped V
in
4000 V
6/25
VND10N06 / VND10N06-1 Electrical specifications
2.3 Electrical characteristics
Tcase = 25 °C unless otherwise stated.
Table 4. Off
Symbol Parameter Test conditions Min. Typ. Max. Unit
V
CLAMP
V
V
I
V
INCL
I
DSS
Table 5. Switching
Drain-Source clamp
voltage
Input low level voltage ID = 100 µA; VDS = 16 V 1.5 V
IL
Input high Level
IH
voltage
Supply current from
ISS
input pin
Input-Source reverse
clamp voltage
Zero input voltage
drain current
= 0V)
(V
IN
(1)
V
= 0V; ID = 200mA 50 60 70 V
IN
= 27Ω; VDD = 16 V
R
L
V
DS
V
DS
I
IN
I
IN
V
DS
V
DS
= 0.5 V
= 0V; V
= -1mA
= 1mA
= 50V; V
< 35V; V
= 5V 150 300 µA
IN
= VIL;
IN
= VIL
IN
3.2 V
-1
8
-0.3
11
250
100µAµA
Symbol Parameter Test conditions Min. Typ. Max. Unit
t
d(on)
t
d(off)
t
d(on)
t
d(off)
(di/dt)
1. Parameters guaranteed by design / characterization.
Table 6. On
Turn-on delay time
= 16V; ID = 1A
V
Rise time 550 900 ns
t
r
Turn-off delay time 200 400 ns
t
Fall time 100 200 ns
f
DD
= 7V; R
V
gen
(see Figure 2)
gen
= 10Ω
Turn-on delay time
= 16V; ID = 1A
V
Rise time 1 1.5 µs
t
r
Turn-off delay time 1.6 2.3 µs
Fall time 1.2 1.8 µs
t
f
Turn-on current slope
on
Total input charge V
Q
i
(1)
DD
= 7V; R
V
gen
(see Figure 2)
V
= 16V; ID = 1A
DD
= 7V; R
V
in
DD
gen
= 12V; ID = 1A; V
gen
= 10Ω
= 1000Ω
IN
= 7V 13 nC
1100 1600 ns
1.2 1.8 µs
1.5 A/µs
V
V
Symbol Parameter Test conditions Min. Typ. Max. Unit
R
DS(on)
1. Pulsed: pulse duration = 300µs, duty cycle 1.5%.
Static Drain-Source
on resistance
= 7V; ID = 1 A; Tj < 125 °C 0.15 0.3 Ω
V
IN
7/25
Electrical specifications VND10N06 / VND10N06-1
Table 7. Dynamic
Symbol Parameter Test conditions Min. Typ. Max. Unit
C
Table 8. Source Drain diode
Output capacitance V
OSS
= 13V; f = 1MHz; V
DS
= 0V 350 500 pF
IN
Symbol Parameter Test conditions Min. Typ. Max. Unit
(1)
V
SD
t
rr
Q
I
RRM
1. Pulsed: pulse duration = 300µs, duty cycle 1.5%.
2. Parameters guaranteed by design / characterization.
Table 9. Protections (-40°C < Tj < 150°C, unless otherwise specified)
Forward on voltage I
(2)
Reverse recovery time
Reverse recovery
(2)
rr
charge
Reverse recovery
(2)
current
= 1 A; V
SD
= 1A; di/dt = 100 A/µs
I
SD
= 30V; Tj = 25°C
V
DD
IN
= V
(see Figure 4)
IL
0.8 1.6 V
125 ns
0.22 µC
3.5 A
Symbol Parameter Test conditions Min. Typ. Max. Unit
I
t
dlim
T
jsh
T
jrs
E
as
1. Parameters guaranteed by design / characterization.
Drain current limit V
lim
Step response current
(1)
limit
Overtemperature
(1)
shutdown
(1)
Overtemperature reset 135 °C
Single pulse
(1)
avalanche energy
= 7V; VDS=13V 6 10 15 A
IN
= 7 V; VDS step from 0 to 13V 12 20 µs
V
IN
150 °C
Starting Tj = 25°C; V
V
= 7V R
IN
= 1kΩ; L = 10mH
gen
DD
= 24V
250 mJ
Figure 2.
Switching waveforms
8/25
Loading...