VN808-32-E
Octal channel high side driver
Features
Type |
RDS(on) |
Iout |
VCC |
VN808-32-E |
150 mΩ |
1 A |
45 V |
|
|
|
|
■VCC/2 compatible input
■Junction overtemperature protection
■Case overtemperature protection for thermal independence of the channels
■Current limitation
■Shorted load protection
■Undervoltage shut-down
■Protection against loss of ground
■Very low stand-by current
■Compliance to 61000-4-4 IEC test up to 4 kV
Description
The VN808-32-E is a monolithic device designed in STMicroelectronics VIPower M0-3 technology, intended for driving any kind of load with one side connected to ground.
PowerSO-36
Active current limitation combined with thermal shutdown and automatic restart, protect the device against overload. In overload condition, channel turns OFF and back ON automatically so as to maintain junction temperature between TTSD and TR. If this condition makes case temperature reach TCSD, overloaded channel is turned OFF and will restart only when case temperature has decreased down to TCR(see waveform 3 Figure 8 on page 11). Non overloaded channels continue to operate normally. Device automatically turns OFF in case of ground pin disconnection. This device is especially suitable for industrial applications conform to IEC 61131.
February 2010 |
Doc ID 14352 Rev 5 |
1/22 |
www.st.com
Contents |
VN808-32-E |
|
|
Contents
1 |
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 3 |
|
2 |
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
4 |
|
3 |
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
6 |
|
4 |
Current, voltage conventions and internal diagram . . . . . . . . . . . . . . . |
8 |
|
5 |
Switching time waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
10 |
|
6 |
Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
13 |
|
7 |
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
14 |
|
|
7.1 |
Footprint recommended data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
16 |
|
7.2 |
Tube shipment information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
17 |
|
7.3 |
Tape and reel shipment information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
18 |
8 |
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
20 |
|
9 |
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
21 |
2/22 |
Doc ID 14352 Rev 5 |
VN808-32-E |
Maximum ratings |
|
|
Table 1. |
Absolute maximum rating |
|
|
|
Symbol |
Parameter |
Value |
Unit |
|
|
|
|
|
|
VCC |
DC supply voltage |
45 |
V |
|
|
DC ground pin reverse current |
-250 |
mA |
|
-IGND |
TRAN Ground pin reverse current |
|||
-6 |
A |
|||
|
(pulse duration < 1ms) |
|||
|
|
|
||
|
|
|
|
|
IOUT |
DC output current |
Internally limited |
A |
|
-IOUT |
Reverse DC output current |
-2 |
A |
|
IIN |
DC Input current |
± 10 |
mA |
|
VIN |
Input voltage range |
-3/+VCC |
V |
|
VESD |
Electrostatic discharge (R = 1.5 kΩ; C = 100 pF) |
2000 |
V |
|
PTOT |
Power dissipation at Tc = 25 °C |
96 |
W |
|
LMAX |
Max inductive load (VCC = 24 V, RLOAD = 48 Ω, |
2 |
H |
|
TA = 100 °C) |
||||
|
|
|
||
TJ |
Junction operating temperature |
Internally limited |
°C |
|
TC |
Case operating temperature |
Internally limited |
°C |
|
TSTG |
Storage temperature |
-40 to 150 |
°C |
Table 2. |
Thermal data |
|
|
|
Symbol |
Parameter |
|
Value |
Unit |
|
|
|
|
|
RthJC |
Thermal resistance junction-case |
Max |
1.3 |
°C/W |
R |
Thermal resistance junction-ambient (1) |
Max |
50 |
°C/W |
thJA |
|
|
|
|
1.When mounted on FR4 printed circuit board with 0.5cm2 of copper area (at least 35 μm think) connected to all TAB pins.
Doc ID 14352 Rev 5 |
3/22 |
Electrical characteristics |
VN808-32-E |
|
|
(10.5 V < VCC < 32 V; -40 °C < TJ < 125 °C; unless otherwise specified)
Table 3. |
Power section |
|
|
|
|
|
Symbol |
Parameter |
Test conditions |
Min |
Typ |
Max |
Unit |
|
|
|
|
|
|
|
VCC |
Operating supply |
|
10.5 |
|
45 |
V |
voltage |
|
|
||||
VUSD |
Undervoltage |
|
7 |
|
10.5 |
V |
shutdown |
|
|
||||
RON |
On state resistance |
IOUT = 0.5 A; TJ = 25 °C |
|
150 |
185 |
mΩ |
IOUT = 0.5 A; |
|
|
280 |
mΩ |
||
|
|
|
|
|||
|
|
OFF state; VCC = 24 V; |
|
|
150 |
μA |
IS |
Supply current |
TCASE = 25 °C |
|
|
|
|
ON state (all channels ON); |
|
|
12 |
mA |
||
|
|
VCC = 24 V, TCASE = 100 °C |
|
|
|
|
ILGND |
Output current at |
VCC = VSTAT = VIN = VGND = 24 V |
|
|
1 |
mA |
turn-off |
VOUT = 0 V |
|
|
|||
|
|
|
|
|
||
IL(off) |
OFF state output |
VIN = VOUT = 0 V; |
0 |
|
5 |
μA |
current |
|
|||||
VOUT(off) |
OFF state output |
VIN = 0 V, IOUT = 0 A |
|
|
3 |
V |
voltage |
|
|
||||
td(Vccon) |
Power-on delay time |
Figure 7 on page 10 |
|
1 |
|
ms |
from VCC rising edge |
|
|
||||
|
|
|
|
|
|
|
Table 4. |
Switching (VCC = 24 V) |
|
|
|
|
|
|
|
|
|
|
|
|
Symbol |
Parameter |
Test conditions |
Min |
Typ |
Max |
Unit |
|
|
|
|
|
|
|
tON |
Turn-on time |
RL = 48 Ω from 80% |
|
50 |
100 |
μs |
VOUT Figure 6. |
|
|||||
|
|
|
|
|
|
|
tOFF |
Turn-off time |
RL = 48 Ω to 10% VOUT Figure 6. |
|
75 |
150 |
μs |
dVOUT/dt(on) |
Turn-on voltage slope |
RL = 48 Ω from VOUT = 2.4 V to |
|
0.7 |
|
V/μs |
VOUT = 19.2 V Figure 6. |
|
|
||||
|
|
|
|
|
|
|
dVOUT/dt(off) |
Turn-off voltage slope |
RL = 48 Ω from VOUT = 21.6 V to |
|
1.5 |
|
V/μs |
VOUT = 2.4 V Figure 6. |
|
|
||||
|
|
|
|
|
|
4/22 |
Doc ID 14352 Rev 5 |
VN808-32-E |
|
|
Electrical characteristics |
||||
|
|
|
|
|
|
|
|
|
Table 5. |
Input pin |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Symbol |
Parameter |
Test conditions |
Min |
Typ |
Max |
Unit |
|
|
|
|
|
|
|
|
|
VINL |
Input low level |
|
|
|
VCC /2-1 |
V |
|
IINL |
Low level input |
VIN = VCC / 2 - 1 V |
80 |
|
|
μΑ |
|
current |
|
|
||||
|
VINH |
Input high level |
|
VCC /2+1 |
|
|
V |
|
IINH |
High level input |
VIN = VCC / 2 + 1 V |
|
150 |
260 |
μΑ |
|
current |
|
|||||
|
VI(HYST) |
Input hysteresis |
|
|
0.6 |
|
V |
|
voltage |
|
|
|
|||
|
IIN |
Input current |
VIN = VCC = 32 V |
|
|
300 |
μΑ |
Table 6. |
Protections |
|
|
|
|
|
|
|
|
|
|
|
|
Symbol |
Parameter |
|
|
Test conditions |
Min |
|
Typ |
|
Max |
Unit |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TCSD |
Case shut-down |
|
|
|
125 |
|
130 |
|
135 |
°C |
|||
temperature |
|
|
|
|
|
||||||||
|
TCR |
Case reset |
|
|
|
110 |
|
|
|
|
|
|
°C |
|
temperature |
|
|
|
|
|
|
|
|
|
|
|
|
TCHYST |
Case thermal |
|
|
|
7 |
|
15 |
|
|
|
°C |
||
hysteresis |
|
|
|
|
|
|
|
||||||
TTSD |
Junction shutdown |
|
|
|
150 |
|
175 |
|
200 |
°C |
|||
temperature |
|
|
|
|
|
||||||||
|
TR |
Junction reset |
|
|
|
135 |
|
|
|
|
|
|
°C |
|
temperature |
|
|
|
|
|
|
|
|
|
|||
THYST |
Junction thermal |
|
|
|
7 |
|
15 |
|
|
|
°C |
||
hysteresis |
|
|
|
|
|
|
|
||||||
|
Ilim |
DC short circuit |
VCC = 24 V; RLOAD = 10 mΩ |
1 |
|
|
|
|
1.7 |
A |
|||
|
current |
|
|
|
|
||||||||
V |
demag |
Turn-off output clamp |
I |
OUT |
= 0.5 A; L = 6 mH |
V -57 |
V |
CC |
-52 |
V |
CC |
-47 |
V |
|
voltage |
|
|
CC |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Table 7. |
Status pin |
|
|
|
|
|
|
Symbol |
Parameter |
Test conditions |
Min |
Typ |
Max |
Unit |
|
|
|
|
|
|
|
|
|
IHSTAT |
High level output |
VCC = 18...32 V; RSTAT = 1 kΩ |
2 |
3 |
4 |
mA |
|
current |
(Fault condition) |
||||||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
ILSTAT |
Leakage current |
Normal operation; VCC = 32 V |
|
|
0.1 |
μA |
|
VCLSTAT |
Clamp voltage |
ISTAT = 1 mA |
6.0 |
6.8 |
8.0 |
V |
|
ISTAT = -1 mA |
|
-0.7 |
|
V |
|||
|
|
|
|
Doc ID 14352 Rev 5 |
5/22 |
Pin connections |
VN808-32-E |
|
|
Table 8. |
Pin functions |
|
|
Pin N° |
|
Symbol |
Function |
|
|
|
|
TAB |
|
VCC |
Positive power supply voltage |
1 |
|
VCC |
Positive power supply voltage |
2,3,4,5 |
|
NC |
Not connected |
|
|
|
|
6 |
|
Input 1 |
Input of channel 1 |
|
|
|
|
7 |
|
Input 2 |
Input of channel 2 |
|
|
|
|
8 |
|
Input 3 |
Input of channel 3 |
|
|
|
|
9 |
|
Input 4 |
Input of channel 4 |
|
|
|
|
10 |
|
Input 5 |
Input of channel 5 |
|
|
|
|
11 |
|
Input 6 |
Input of channel 6 |
|
|
|
|
12 |
|
Input 7 |
Input of channel 7 |
|
|
|
|
13 |
|
Input 8 |
Input of channel 8 |
|
|
|
|
14,15,16,17,18 |
NC |
Not connected |
|
|
|
|
|
19 |
|
GND |
Logic ground |
|
|
|
|
20 |
|
STATUS |
Common open source diagnostic for over-temperature |
|
|
|
|
21,22 |
|
Output 8 |
High-side output of channel 8 |
|
|
|
|
23,24 |
|
Output 7 |
High-side output of channel 7 |
|
|
|
|
25,26 |
|
Output 6 |
High-side output of channel 6 |
|
|
|
|
6/22 |
Doc ID 14352 Rev 5 |
VN808-32-E |
|
|
Pin connections |
|
|
|
|
|
|
|
Table 8. |
Pin functions (continued) |
||
|
|
|
|
|
|
Pin N° |
|
Symbol |
Function |
|
|
|
|
|
|
27.28 |
|
Output 5 |
High-side output of channel 5 |
|
|
|
|
|
|
29,30 |
|
Output 4 |
High-side output of channel 4 |
|
|
|
|
|
|
31,32 |
|
Output 3 |
High-side output of channel 3 |
|
|
|
|
|
|
33,34 |
|
Output 2 |
High-side output of channel 2 |
|
|
|
|
|
|
35,36 |
|
Output 1 |
High-side output of channel 1 |
|
|
|
|
|
Doc ID 14352 Rev 5 |
7/22 |