TSV611, TSV611A, TSV612, TSV612A
Features
■ Rail-to-rail input and output
■ Low power consumption: 10 µA typ at 5 V
■ Low supply voltage: 1.5 to 5.5 V
■ Gain bandwidth product: 120 kHz typ
■ Unity gain stable
■ Low input offset voltage: 800 µV max (A
version)
■ Low input bias current: 1 pA typ
■ Temperature range: -40 to +85° C
Applications
■ Battery-powered applications
■ Smoke detectors
■ Proximity sensors
■ Portable devices
■ Signal conditioning
■ Active filtering
■ Medical instrumentation
Rail-to-rail input/output 10 µA, 120 kHz
CMOS operational amplifiers
TSV611ILT - TSV611ICT
V
In+
In+
1
1
+
+
_
V
V
CC-
CC-
In-
In-
_
2
2
3
3
SOT23-5/SC70-5
TSV612IST - TSV612ID/DT
Out1
Out1
1
1
_
In1-
In1-
In1+
In1+
V
V
CC-
CC-
_
2
2
+
+
3
3
4
4
MiniSO-8/SO-8
V
5
5
CC+
CC+
4
4
Out
Out
8
8
V
V
CC+
CC+
7
7
Out2
Out2
_
_
+
+
In2-
In2-
6
6
In2+
In2+
5
5
Description
The TSV61x family of single and dual operational
amplifiers offers low voltage, low power operation
and rail-to-rail input and output.
The devices also feature an ultra-low input bias
current as well as a low input offset voltage.
The TSV61x have a gain bandwidth product of
120 kHz while consuming only 10 µA at 5 V.
These features make the TSV61x family ideal for
sensor interfaces, battery supplied and portable
applications, as well as active filtering.
January 2010 Doc ID 15768 Rev 2 1/19
www.st.com
19
Absolute maximum ratings and operating conditions TSV611, TSV611A, TSV612, TSV612A
1 Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Symbol Parameter Value Unit
(3)
(1)
(7)
(2)
(6)
(8)
(4)(5)
V
CC-
6V
±V
CC
-0.2 to V
+0.2 V
CC+
V
°C/W
4kV
200 V
1.5 kV
V
CC
V
V
T
stg
Supply voltage
Differential input voltage
id
Input voltage
in
Storage temperature -65 to +150 °C
Thermal resistance junction to ambient
SC70-5 205
R
thja
SOT23-5 250
MiniSO-8 190
SO-8 125
T
Maximum junction temperature 150 °C
j
HBM: human body model
ESD
MM: machine model
CDM: charged device model
Latch-up immunity 200 mA
1. All voltage values, except differential voltage are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. Vcc-Vin must not exceed 6 V.
4. Short-circuits can cause excessive heating and destructive dissipation.
5. Rth are typical values.
6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
8. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to ground.
Table 2. Operating conditions
Symbol Parameter Value Unit
T
V
V
CC
icm
oper
Supply voltage 1.5 to 5.5 V
Common mode input voltage range V
Operating free air temperature range -40 to +85 °C
2/19 Doc ID 15768 Rev 2
CC-
-0.1 to V
+0.1 V
CC+
TSV611, TSV611A, TSV612, TSV612A Electrical characteristics
2 Electrical characteristics
Table 3. Electrical characteristics at V
with V
= 0 V, V
CC-
= VCC/2, T
icm
(unless otherwise specified)
Symbol Parameter Conditions Min. Typ. Max. Unit
DC performance
= +1.8 V
CC+
= 25° C, and RL connected to VCC/2
amb
V
Offset voltage
io
DV
CMR
V
V
Input offset voltage drift 2 μV/°C
io
Input offset current
I
io
(V
out=Vcc
Input bias current
I
ib
(V
out=Vcc
Common mode rejection
ratio 20 log (ΔVic/ΔVio)
Large signal voltage gain
A
vd
High level output voltage
OH
Low level output voltage
OL
Isink
I
out
Isource
Supply current (per
I
CC
operator)
AC performance
/2)
/2)
TSV61x
TSV61xA
< Top < T
T
min.
< Top < T
T
min.
T
< Top < T
min.
T
< Top < T
min.
0 V to 1.8 V, V
< Top < T
T
min.
= 10 kΩ, Vout = 0.5 V to
R
L
TSV61x
max.
TSV61xA
max
1 100 pA
max.
1 100 pA
max.
= 0.9 V 55 71 dB
out
max.
1.3 V
< Top < T
T
min.
=10kΩ
R
L
< Top < T
T
min.
=10kΩ
R
L
< Top < T
T
min.
= 1.8 V
V
o
T
< Top < T
min.
= 0 V
V
o
T
< Top < T
min.
No load, V
< Top < T
T
min.
max.
max.
max.
max.
max.
out=Vcc
max.
/2 6.5 9 12 µA
4
0.8
mV
5
2
110
110
(1)
(1)
pA
pA
53 dB
78 83 dB
74 dB
35
50
9
4
735
50
13
mV
mV
9
mA
8
10
8
612.5µA
GBP Gain bandwidth product RL=10kΩ, CL= 20 pF 100 kHz
φm Phase margin R
Gain margin RL=10kΩ, CL=20pF 9.5 dB
G
m
SR Slew rate
=10kΩ, CL= 20 pF 60 Degrees
L
R
=10kΩ, CL=20pF,
L
= 0.5V to 1.3V
V
out
0.03 V/μs
Doc ID 15768 Rev 2 3/19
Electrical characteristics TSV611, TSV611A, TSV612, TSV612A
Table 3. Electrical characteristics at V
with V
= 0 V, V
CC-
= VCC/2, T
icm
= +1.8 V
CC+
= 25° C, and RL connected to VCC/2
amb
(unless otherwise specified) (continued)
Symbol Parameter Conditions Min. Typ. Max. Unit
Equivalent input noise
e
n
voltage
THD+N
1. Guaranteed by design.
Total harmonic distortion +
noise
f = 1 kHz 110
= 1 kHz, Av = 1,
F
in
V
out
= 1 V
pp, RL
= 100 kΩ,
0.07 %
BW = 22 kHz
nV
-----------Hz
4/19 Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A Electrical characteristics
Table 4. V
Symbol Parameter Min. Typ. Max. Unit
DC performance
= +3.3 V, V
CC+
R
connected to VCC/2 (unless otherwise specified)
L
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C,
amb
V
Offset voltage
io
DV
CMR
V
V
Input offset voltage drift 2 μV/°C
io
I
Input offset current
io
I
Input bias current
ib
Common mode rejection
ratio 20 log (ΔV
Large signal voltage gain
A
vd
High level output voltage
OH
Low level output voltage
OL
Isink
I
out
Isource
Supply current (per
I
CC
operator)
AC performance
/ΔVio)
ic
TSV61x
TSV61xA
T
min<Top<Tmax
T
min<Top<Tmax
< Top < T
T
min.
< Top < T
T
min.
0 V to 3.3 V, V
< Top < T
T
min.
TSV61x
TSV61xA
1 100 pA
max.
1 100 pA
max.
= 1.75 V 61 76 dB
out
58 dB
max.
RL=10kΩ, Vout = 0.5 V to
2.8 V
< Top < T
T
min.
=10kΩ
R
L
T
< Top < T
min.
=10kΩ
R
L
T
< Top < T
min.
V
= V
o
CC
T
< Top < T
min.
V
= 0 V
o
< Top < T
T
min.
No load, V
T
< Top < T
min.
max.
max.
max.
max.
max.
=VCC/2 6.5 9.5 12.5 µA
out
max.
4
0.8
mV
5
2
110
110
(1)
(1)
pA
pA
85 92 dB
83 dB
35
50
5
10 35
50
mV
mV
373544
mA
323038
613µA
GBP Gain bandwidth product R
φm Phase margin R
G
Gain margin RL = 10 kΩ, CL=20pF, 9.5 dB
m
SR Slew rate
Equivalent input noise
e
n
voltage
1. Guaranteed by design.
Doc ID 15768 Rev 2 5/19
=10kΩ, CL=20pF 110 kHz
L
= 10 kΩ, CL=20pF 60 Degrees
L
=10kΩ, CL= 20 pF, V
R
L
= 0.5V to 2.8V
out
0.035 V/μs
f=1kHz 110
nV
-----------Hz
Electrical characteristics TSV611, TSV611A, TSV612, TSV612A
Table 5. V
= +5 V, V
CC+
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C, RL connected to VCC/2
amb
(unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit
DC performance
V
Offset voltage
io
DV
CMR
SVR
V
V
Input offset voltage drift 2 μV/°C
io
I
Input offset current
io
I
Input bias current
ib
Common mode rejection
ratio 20 log (ΔV
Supply voltage rejection
ratio 20 log (ΔV
A
Large signal voltage gain
vd
High level output voltage
OH
Low level output voltage
OL
Isink
I
out
Isource
Supply current (per
I
CC
operator)
AC performance
/ΔVio)
ic
/ΔVio)
cc
TSV61x
TSV61xA
4
0.8
mV
T
min<Top<Tmax
T
min<Top<Tmax
< Top < T
T
min.
< Top < T
T
min.
0V to 5V, V
< Top < T
T
min.
TSV61x
TSV61xA
110
1 100 pA
max.
110
1 100 pA
max.
= 2.5 V 64 80 dB
out
63 dB
max.
5
2
(1)
pA
(1)
pA
Vcc = 1.8 to 5 V 76 93 dB
T
< Top < T
min.
=10kΩ, Vout = 0.5 V to
R
L
4.5 V
T
min<Top<Tmax
R
=10kΩ
L
T
< Top < T
min.
R
=10kΩ
L
T
< Top < T
min.
V
= V
o
CC
T
< Top < T
min.
= 0 V
V
o
< Top < T
T
min.
No load, V
T
min.
out=VCC
< Top < T
74 dB
max.
88 93 dB
85 dB
max.
35
50
7
16 35
max.
50
524257
max.
584963
max.
/2 7.5 10.5 14 µA
max.
715µA
mV
mV
mA
GBP Gain bandwidth product R
φm Phase margin R
Gain margin RL = 10 kΩ, CL=20pF 10 dB
G
m
SR Slew rate
=10kΩ, CL= 20 pF 120 kHz
L
= 10 kΩ, CL=20pF 62 Degrees
L
R
=10kΩ, CL= 20 pF,
L
V
= 0.5V to 4.5V
out
6/19 Doc ID 15768 Rev 2
0.04 V/μs
TSV611, TSV611A, TSV612, TSV612A Electrical characteristics
Table 5. V
= +5 V, V
CC+
= 0 V, V
CC-
(unless otherwise specified) (continued)
Symbol Parameter Min. Typ. Max. Unit
Equivalent input noise
e
n
voltage
THD+N
1. Guaranteed by design.
Total harmonic distortion +
noise
Figure 1. Supply current vs. supply voltage
at V
icm
= VCC/2
= VCC/2, T
icm
= 25° C, RL connected to VCC/2
amb
f = 1 kHz 105
= 1 kHz, Av = 1,
F
in
V
out
= 1 V
pp, RL
= 100 kΩ,
0.02 %
BW = 22kHz
Figure 2. Output current vs. output voltage at
VCC=1.5V
nV
-----------Hz
Figure 3. Output current vs. output voltage at
V
=5V
CC
Figure 4. Voltage gain and phase vs.
frequency at VCC = 1.5 V
Gain (dB)
Phase margin (°)
Doc ID 15768 Rev 2 7/19
Electrical characteristics TSV611, TSV611A, TSV612, TSV612A
Ω
Figure 5. Voltage gain and phase vs.
frequency at V
Gain (dB)
Figure 7. Positive slew rate vs. time, V
= 100 pF, R
C
Load
Amplitude (V)
VCC=1.5V, V
R
T=−40°C
T=25°C
=10kΩ, C
Load
CC
Load
=5V
= 10 kΩ
T=85°C
icm=VCC
=100pF
Load
CC
/2
= 1.5 V,
Figure 6. Phase margin vs. output current
Phase margin(°)
Figure 8. Negative slew rate vs. time, V
C
Load
= 100 pF, R
T=-40°C
T=25°C
= 10 kΩ
Load
VCC=1.5V, V
R
=10kΩ, C
Load
V
/2
Load=VCC
icm=VCC
Load
T=85°C
=100pF
CC
/2,
= 1.5 V,
Time (µs)
Figure 9. Positive slew rate vs. time, V
C
Load
= 100 pF, R
Load
= 100 kΩ
Ω
CC
= 5.5 V,
Figure 10. Negative slew rate vs. time, V
8/19 Doc ID 15768 Rev 2
C
Load
Time (µs)
= 100 pF, R
Load
= 100 kΩ
CC
= 5.5 V,
TSV611, TSV611A, TSV612, TSV612A Electrical characteristics
Gain (dB)
Phase margin (°)
Figure 11. Slew rate vs. supply voltage Figure 12. Noise vs. frequency at Vcc = 5 V
Vicm=2.5V
VCC=5V
Input equivalent noise density (nV/VHz)
T=25°C
Vicm=4.5V
Frequency (Hz)
Figure 13. Distortion + noise vs. frequency Figure 14. Distortion + noise vs. output
voltage
1
Vcc=1.5V
Ω
Rl=10k
0.1
THD + N (%)
0.01
10 100 1000 10000
Vcc=1.5V
Rl=100k
Ω
Ω
Ω
THD + N (%)
Vcc=1.5V
Rl=10kohms
Vcc=1.5V
Rl=100kohms
Vcc=5.5V
Rl=10kohms
Vcc=5.5V
Rl=100kohms
Output Voltage (Vpp)
f=1kHz
Gain=1
BW=22kHz
Vicm=Vcc/2
Figure 15. Voltage gain and phase vs.
Gain (dB)
frequency at V
CC
simulation results)
= 1.8 V (based on
Phase margin (°)
Figure 16. Voltage gain and phase vs.
frequency at VCC = 5 V (based on
simulation results)
Doc ID 15768 Rev 2 9/19
Application information TSV611, TSV611A, TSV612, TSV612A
0.00.0 1.01.0 2.02.0 3.03.0 4.04.0 5.05.0
-1.0-1.0
-0.8-0.8
-0.6-0.6
-0.4-0.4
-0.2-0.2
0.00.0
0.20.2
0.40.4
0.60.6
0.80.8
1.01.0
1.21.2
1.41.4
Input Offset Voltage (mV)
Input Common Mode Voltage (V)
3 Application information
3.1 Operating voltages
The TSV61x can operate from 1.5 to 5.5 V. Their parameters are fully specified for 1.8, 3.3
and 5 V power supplies. However, the parameters are very stable in the full V
several characterization curves show the TSV61x characteristics at 1.5 V. Additionally, the
main specifications are guaranteed in extended temperature ranges from -40° C to +85° C.
3.2 Rail-to-rail input
The TSV61x are built with two complementary PMOS and NMOS input differential pairs.
The devices have a rail-to-rail input, and the input common mode range is extended from
V
-0.1 V to V
CC-
the transition region, the performance of CMRR, PSRR, V
(as shown in Figure 17 and Figure 18 for V
Figure 17. Input offset voltage vs input
common mode at V
1.51.5
+0.1 V. The transition between the two pairs appears at V
CC+
= 1.5 V
CC
and THD is slightly degraded
vs. V
io
icm
io
).
Figure 18. Input offset voltage vs input
common mode at V
CC
range and
CC
-0.7 V. In
CC+
= 5 V
1.01.0
0.50.5
0.00.0
-0.5-0.5
Input Offset Voltage (mV)
-1.0-1.0
-1.5-1.5
0.00.0 0.20.2 0.40.4 0.60.6 0.80.8 1.01.0 1.21.2 1.41.4
Input Common Mode Voltage (V)
The device is guaranteed without phase reversal.
3.3 Rail-to-rail output
The operational amplifiers’ output levels can go close to the rails: less than 35 mV above
GND rail and less than 35 mV below V
3.4 Driving resistive and capacitive loads
These products are micro-power, low-voltage operational amplifiers optimized to drive rather
10/19 Doc ID 15768 Rev 2
large resistive loads, above 10 kΩ. For lower resistive loads, the THD level may significantly
increase.
rail when connected to 10 kΩ load to VCC/2.
CC
TSV611, TSV611A, TSV612, TSV612A Application information
In a follower configuration, these operational amplifiers can drive capacitive loads up to
100 pF with no oscillations. When driving larger capacitive loads, adding an in-series
resistor at the output can improve the stability of the devices (see Figure 19 for
recommended in-series resistor values). Once the in-series resistor value has been
selected, the stability of the circuit should be tested on bench and simulated with the
simulation model.
Figure 19. In-series resistor vs. capacitive load
(Ω)
In-series resistor
3.5 PCB layouts
For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible
to the power supply pins.
3.6 Macromodel
An accurate macromodel of the TSV61x is available on STMicroelectronics’ web site at
www.st.com. This model is a trade-off between accuracy and complexity (that is, time
simulation) of the TSV61x operational amplifiers. It emulates the nominal performances of a
typical device within the specified operating conditions mentioned in the datasheet. It also
helps to validate a design approach and to select the right operational amplifier, but it does
not replace on-board measurements.
Doc ID 15768 Rev 2 11/19
Package information TSV611, TSV611A, TSV612, TSV612A
4 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK®
®
is an ST trademark.
12/19 Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A Package information
4.1 SOT23-5 package information
Figure 20. SOT23-5 package mechanical drawing
Table 6. SOT23-5 package mechanical data
Dimensions
Ref.
Min. Typ. Max. Min. Typ. Max.
A 0.90 1.20 1.45 0.035 0.047 0.057
A1 0.15 0.006
A2 0.90 1.05 1.30 0.035 0.041 0.051
B 0.35 0.40 0.50 0.013 0.015 0.019
C 0.09 0.15 0.20 0.003 0.006 0.008
D 2.80 2.90 3.00 0.110 0.114 0.118
D1 1.90 0.075
e 0.95 0.037
E 2.60 2.80 3.00 0.102 0.110 0.118
F 1.50 1.60 1.75 0.059 0.063 0.069
L 0.10 0.35 0.60 0.004 0.013 0.023
K 0 degrees 10 degrees
Millimeters Inches
Doc ID 15768 Rev 2 13/19
Package information TSV611, TSV611A, TSV612, TSV612A
4.2 SC70-5 (SOT323-5) package information
Figure 21. SC70-5 (SOT323-5) package mechanical drawing
DIMENSIONS IN MM
GAUGE PLANE
SEATING PLANE
SIDE VIEW
COPLANAR LEADS
TOP VIEW
Table 7. SC70-5 (SOT323-5) package mechanical data
Dimensions
Ref
Min Typ Max Min Typ Max
A 0.80 1.10 0.315 0.043
A1 0.10 0.004
A2 0.80 0.90 1.00 0.315 0.035 0.039
b 0.15 0.30 0.006 0.012
c 0.10 0.22 0.004 0.009
D 1.80 2.00 2.20 0.071 0.079 0.087
E 1.80 2.10 2.40 0.071 0.083 0.094
E1 1.15 1.25 1.35 0.045 0.049 0.053
e 0.65 0.025
e1 1.30 0.051
L 0.26 0.36 0.46 0.010 0.014 0.018
<0° 8°
Millimeters Inches
14/19 Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A Package information
4.3 SO-8 package information
Figure 22. SO-8 package mechanical drawing
Table 8. SO-8 package mechanical data
Dimensions
Ref.
Min. Typ. Max. Min. Typ. Max.
A1.750.069
A1 0.10 0.25 0.004 0.010
A2 1.25 0.049
b 0.28 0.48 0.011 0.019
c 0.17 0.23 0.007 0.010
D 4.80 4.90 5.00 0.189 0.193 0.197
E 5.80 6.00 6.20 0.228 0.236 0.244
E1 3.80 3.90 4.00 0.150 0.154 0.157
e 1.27 0.050
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
L1 1.04 0.040
k1° 8°1° 8°
ccc 0.10 0.004
Millimeters Inches
Doc ID 15768 Rev 2 15/19
Package information TSV611, TSV611A, TSV612, TSV612A
4.4 MiniSO-8 package information
Figure 23. MiniSO-8 package mechanical drawing
Table 9. MiniSO-8 package mechanical data
Dimensions
Ref.
Min. Typ. Max. Min. Typ. Max.
A 1.1 0.043
A1 0 0.15 0 0.006
A2 0.75 0.85 0.95 0.030 0.033 0.037
b 0.22 0.40 0.009 0.016
c 0.08 0.23 0.003 0.009
D 2.80 3.00 3.20 0.11 0.118 0.126
E 4.65 4.90 5.15 0.183 0.193 0.203
E1 2.80 3.00 3.10 0.11 0.118 0.122
e 0.65 0.026
L 0.40 0.60 0.80 0.016 0.024 0.031
L1 0.95 0.037
L2 0.25 0.010
k0° 8°0° 8°
ccc 0.10 0.004
Millimeters Inches
16/19 Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A Ordering information
5 Ordering information
Table 10. Order codes
Order code
TSV611ILT
TSV611AILT K11
TSV611ICT
TSV611AICT K11
TSV612ID/DT
TSV612AID/DT V612AI
TSV612IST
TSV612AIST K115
Temperature
range
-40° C to 85° C
Package Packing Marking
K12
SOT23-5
Tape & reel
K12
SC70-5
V612I
SO-8 Tube & tape & reel
K113
MiniSO-8 Tape & reel
Doc ID 15768 Rev 2 17/19
Revision history TSV611, TSV611A, TSV612, TSV612A
6 Revision history
Table 11. Document revision history
Date Revision Changes
28-May-2009 1 Initial release.
18-Jan-2010 2
Full datasheet for product now in production.
Added Figure 1 to Figure 19.
18/19 Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15768 Rev 2 19/19
Loading...