STM32L152D-EVAL evaluation board
Features
■ STM32L152ZDT6 microcontroller
■ Four 5 V power supply options:
–Power jack
– ST-LINK/V2 USB connector
– User USB connector
– Daughterboard
■ Audio jack connected to I2S DAC or
STM32L152ZDT6 internal DAC
■ Microphone connected to ADC using
integrated op amp as amplifier
■ 2 GByte (or more) MicroSD Card on SDIO
■ Temperature sensor and RF EEPROM on I2C
compatible serial interface
■ RS-232 interface configurable for
communication or Flash loader
■ IrDA transceiver
■ 4 Kbit serial Flash, 512 K x 16-bit SRAM and
128 Mbit NOR Flash
■ 240x320 TFT color LCD connected to FSMC
interface of STM32L152ZDT6
■ Joystick with 4-direction control and selector
■ Reset and Tamper or key button
■ 4 color user LEDs
■ 3 LEDs for MCU power range indicator
■ MCU consumption measurement circuit
■ 40x8 glass LCD segments connected to LCD
driver of the STM32L152ZDT6
■ Extension connector for daughterboard or
wrapping board
■ MCU voltage; 3.3 V or adjustable 1.65 V-3.6 V
■ USB FS connector
■ Touch slider
■ Light dependent resistor (LDR)
■ ADC/ DAC input signal connector
STM32L152D-EVAL
Data brief − production data
■ MCU integrated op amp configured as Sallen-
Key 2nd order low pass filter
■ MCU integrated op amp configured as amplifier
with adjustable gain
■ Potentiometer
■ JTAG and trace debug support
■ Embedded ST-LINK/V2
Description
The STM32L152D-EVAL evaluation board is a
complete demonstration and development
platform for the STM32 L1 series of ultra-lowpower MCUs and includes an STM32L152ZDT6
ARM Cortex-M3 32-bit microcontroller with
384 KB of Flash memory. An ST-LINK/V2 is
integrated on the board as an embedded in-circuit
debugger / programmer for the STM32L152ZDT6.
The full range of hardware features on the board
helps you develop your own applications and
evaluate all peripherals (USB FS, USART, audio
DAC, microphone ADC, dot-matrix LCD, LCD
glass, IrDA, LDR, SRAM, NOR Flash, MicroSD
Card, temperature sensor and so on).
Extension headers facilitate easy connection of
daughterboard or wrapping board for your
application.
March 2012 Doc ID 022834 Rev 1 1/3
This is information on a product in full production. For further information contact your local STMicroelectronics sales
office.
www.st.com
3
Ordering information STM32L152D-EVAL
Ordering information
Table 1. Product summary
Order code Reference
STM32L152D-EVAL STM32L152D-EVAL evaluation board
Revision history
Table 2. Document revision history
Date Revision Changes
16-Mar-2012
1 Initial release.
2/3 Doc ID 022834 Rev 1
STM32L152D-EVAL
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 022834 Rev 1 3/3
Loading...