ST STM3220F-EVAL, STM32F207IFT6 User Manual

Download

Page 1

UMxxxx

ser Manual

STM3220F-EVAL

Evaluation Board

Introduction

The STM32F207IFT6 evaluation board STM3220F-EVAL is designed as complete development platform for STMicroelectronic’s ARM Cortex-M3 core-based STM32F207IFT6 microcontroller with dig ita l c am er a module interface, High speed USB OTG, Full speed USB OTG, Ethernet MAC, FSMC interface, two channels of CAN2.0A/B compliant interface, 2 channels I2S, 3 channels I2C, 6 channels USART with smart card support, 3 channels SPI, SDIO, 3 ADC, 2 DAC, internal 128KB SRAM and 1MB Flash, JTAG&SWD debugging support.

The full range of hardware features on the board is able to help you evaluate all peripherals (USB OTG HS, USB OTG FS, Ethernet, Motor Control, CAN, MicroSD card, Smart card, USART, Audio DAC, RS232, IrDA, PSRAM, OneNAND, MEMS, EEPROM… etc.) and develop your own applications. Extension headers make it possible to easily connect a daughter board or wrapping board for your specific application.

Features

■

Four 5V power supply options: Power jack, USB FS connector, USB HS connector or daughter board.

■

Boot from User Flash, System memory or SRAM.

■

I2S Audio DAC, stereo audio jack.

■

1GByte or more MicroSD card.

■

Both type A&B Smart card support.

■

I2C compatible serial interface 64KBit EEPROM, MEMS and IO Expander.

■

RS232 communication.

■

IrDA transceiver.

■

USB OTG HS and FS with Micro-AB connector.

■

IEEE-802.3-2002 compliant Ethernet connector.

■

Camera module

■

4Mbit PSRAM

■

512Mbit OneNAND

■

Two channels of CAN2.0A/B compliant connection.

■

Inductor Motor Control connector.

Figure 1: STM3220F-EVAL evaluation board

Page 2

STM3220F-EVAL Board

Qing SHAO Page 2 03/06/2009

■

JTAG ,SW and Trace Debug support.

■

3.2” 240x320 TFT color LCD with touch screen.

■

Joystick with 4-direction control and selector.

■

Reset, Wakeup, Tamper and User button.

■

4 color LEDs.

■

RTC with backup battery.

■

MCU consumption measurement circuit

■

Extension connector for daughter board or wrapping board.

Page 3

STM3220F-EVAL Board

Qing SHAO Page 3 03/06/2009

Contents

1. Hardware Layout and configuration ...................................................................................... 4

1.1 Power Supply.................................................................................................................. 6

1.2 Boot Option ..................................................................................................................... 7

1.3 Clock Source................................................................................................................... 8

1.4 Reset Source................................................................................................................... 8

1.5 Audio ............................................................................................................................... 8

1.6 EEPROM......................................................................................................................... 8

1.7 CAN................................................................................................................................. 8

1.8 RS232 & IrDA................................................................................................................ 10

1.9 Motor Control................................................................................................................. 10

1.10 Smart Card..................................................................................................................11

1.11 MicroSD card............................................................................................................... 12

1.12 MEMS.......................................................................................................................... 12

1.13 Analog Input................................................................................................................ 12

1.14 USB OTG FS............................................................................................................... 13

1.15 Ethernet....................................................................................................................... 13

1.16 USB OTG HS .............................................................................................................. 14

1.17 Camera Module........................................................................................................... 14

1.18 PSRAM and OneNAND .............................................................................................. 14

1.19 Development and Debug support ............................................................................... 14

1.20 Display and Input devices ........................................................................................... 14

1.21 IDD measurement and comparator............................................................................. 15

2. Connector ............................................................................................................................ 17

2.1 Daughter board extension connector CN1,2,3 and CN4 .............................................. 17

2.2 Motor control connector CN5 ........................................................................................ 21

2.3 MicroSD connector CN6 ............................................................................................... 22

2.4 Ethernet RJ45 connector CN7...................................................................................... 22

2.5 USB OTG FS Micro-AB connector CN8 ....................................................................... 23

2.6 USB OTG HS Micro-AB connector CN9 ....................................................................... 23

2.7 CAN D-type 9-pins male connector CN10(CAN2) & CN12(CAN1) .............................. 24

2.8 Audio connector CN11..................................................................................................24

2.9 Trace debugging connector CN13 ................................................................................ 24

2.10 JTAG debugging connector CN14.............................................................................. 25

2.11 Camera module connector CN15................................................................................ 25

2.12 RS232 connector CN16.............................................................................................. 26

2.13 Analog input connector CN17 ..................................................................................... 26

2.14 Power connector CN18...............................................................................................26

2.15 TFT LCD connector CN19 .......................................................................................... 27

2.16 Smart card connector CN20........................................................................................ 27

3. Known limitations and bugs on PCB rev A..........................................................................28

4. Schematic............................................................................................................................29

Appendix A STM3220F-EVAL IO Assignment........................................................................ 49

Appendix B Document Revision History.................................................................................. 53

Page 4

STM3220F-EVAL Board

Qing SHAO Page 4 03/06/2009

1. Hardware Layout and configuration

The STM3220F-EVAL evaluation board is designed around the STM32F207IFT6 in 176-pin TQFP package. The hardware block diagram Figure 2 illustrates the connection between STM32F207IFT6 and peripherals (Camera module, LCD, PSRAM, OneNAND, EEPROM, MEMS, USART, IrDA, USB OTG HS, USB OTG FS, Ethernet, Audio, CAN bus, Smart card, MicroSD card and Motor Control) and Figure 3 will he l p you loc ate these featur es on the actual evaluation board.

Figure 2: Hardware Block Diagram

STM32F207IFT6

RS232

transceiver

IrDA

transceiver

Smart Card

interface

3.3V regulator

TFT LCD

MicroSD

card

Audio DAC

BNC connector

MC control

connector

LEDs,Key

JTAG/SWD

MEMS

Potentiometer

Smart Card

connector

Integrated RJ45

connector

RS232

DB9 connector

ADC

I2S2

GPIO

MII/RMII

USART6

I2C1

Extension

connector for

GPIOs

MCU

consumption

measurement

PHY

USART3

CAN1

CAN

transceiver

CAN

DB9 connector

SDIO

Trace

Debug

OTG FS

USB Micro-AB

connector

EEPROM

IO expandor

Joystick

Touchscreen

USB power

switch

CAN2

CAN

transceiver

CAN

DB9 connector

2.8V regulator

2.5V regulator

1.8V regulator

DCMI

Camera

module

OTG HS

USBMicro-AB

connector

USB power

switch

USB HS

PHY

DAC

FSMCPSRAM

OneNAND

Page 5

STM3220F-EVAL Board

Qing SHAO Page 5 03/06/2009

Figure 3: STM3220F-EVAL Evaluation board layout

CN8 USB OTG FS

CN14 JTAG

U32 Jo

stick

B2 WAKEUP

B4 User Key

B1 RESET

CN19 Color LCD

CN12 CAN1

CN6 MicroSD

U16 STM32F207IFT6

CN16 USART3

CN11 Audio Jack

CN1-CN4 Extension header

U11 IrDA

CN17 Motor control

CN17 BNC connecto

RV1 Potentiometer

B3 Tamper

CN20 Smartcard

CN9 USB OTG HS

CN7 RJ45 connector

CN10 CAN2

CN18 5V power jack

CN15 Camera module

CN13 Trace

Page 6

STM3220F-EVAL Board

Qing SHAO Page 6 03/06/2009

1.1 Power Supply

STM3220F-EVAL evaluation board is designed to be powered by 5V DC power supply and to be protected by PolyZen from wrong power plug-in event. It’s possible to configure the evaluation board to use any of following Four sources for the power supply.

■

5V DC power adapter connected to CN18, the Power Jack on the board (PSU on silk screen for Power Supply Unit).

■

5V DC power with 500mA limitation from CN8, the USB OTG FS Micro-AB connector (FS on silkscreen).

■

5V DC power with 500mA limitation from CN9, the USB OTG HS Micro-AB connector (HS on silkscreen).

■

5V DC power from both CN1 and CN3, the extension connector for daughter board (DTB for Daughter Board on silkscreen).

The power supply is configured by setting the related jumpers JP17, JP18 & JP19 as described in table 1.

Table 1 Power related Jumpers

Jumper Description

JP17

JP17 is used to measure MCU current consumption manually by multimeter.

Default setting: Fitted JP18 is used to select one of the four possible power supply resources.

For power supply jack(CN18) to the STM3220F-EVAL only

, JP18 is set as shown to the right: (Default Setting)

For power supply from the daughter board connectors(CN1 and CN3) to STM3220F-EVAL only

, JP18 is set as shown to the right:

For power supply from USB OTG FS (CN8) to STM3220F-EVAL only, JP18 is set as shown to the right:

JP18

For power supply from USB OTG HS (CN9) to STM3220F-EVAL only

JP18 is set as shown to the right:

HS FS DTB PSU

Page 7

STM3220F-EVAL Board

Qing SHAO Page 7 03/06/2009

For power supply from power supply jack(CN18) to both STM3220FEVAL and daughter board connected on CN1 and CN3, JP18 is set as shown to the right (daughter board must not have its own power supply connected)

Vbat is connected to battery when JP19 is set as shown to the right:

JP19

Vbat is connected to 3.3V power when JP19 is set as shown to the right: (Default setting)

To enable MCU power consumption measurement, JP16 should be re-configured as described in table 2.

Table 2 MCU Power consumption measurement related Jumpers

JP16

JP16 is useded to bypass MCU power consumption measurement circuit, it’s set to close by default.

JP16 need to be re-configured to open for MCU power consumption measurement.

Default setting: Fitted

The LED LD9 is lit when the STM3220F-EVAL evaluation board is powered by the 5V correctly.

1.2 Boot Option

The STM3220F-EVAL evaluation board is able to boot from:

■

Embedded User Flash

■

System memory with boot loader for ISP

■

Embedded SRAM for debugging

The boot option is configured by setting switch SW1 (BOOT1) and SW2 (BOOT0). The BOOT0 can be configured also via RS232 connector CN16.

Table 3 Boot related Switch

Switch Boot from

Switch configuration

STM3220F-EVAL boot from User Flash when BOOT0 is set as shown to the right. BOOT1 is don’t care in this configuration. (Default setting) STM3220F-EVAL boot from Embedded SRAM when BOOT0 and BOOT1 are set as shown to the right.

BOOT0 & 1

STM3220F-EVAL boot from System Memory when BOOT0 and BOOT1 are set as shown to the right.

HS FS DTB PSU

1 2 3

Page 8

STM3220F-EVAL Board

Qing SHAO Page 8 03/06/2009

1.3 Clock Source

Four clock sources are available on STM3220F-EVAL evaluation board for STM32F207IFT6 and RTC embedded.

■

X1, 25MHz Crystal for Ethernet PHY.

■

X2, 24MHz Crystal for USB OTG HS PHY.

■

X3, 32KHz Crystal for embedded RTC.

■

X4, 25MHz Crystal with socket for STM32F207IFT6 Microcontroller, it can be removed from socket when internal RC clock is used.

1.4 Reset Source

The reset signal of STM3220F-EVAL evaluation board is low active and the reset sources include:

■

Reset button B1

■

Debugging Tools from JTAG connector CN14 and Trace connector CN13

■

Daughter board from CN3

■

RS232 connector CN16 for ISP.

Table 4 Reset Related Jumpers

Jumper Description

JP25

Enable reset of the STM32F207IFT6 embedded JTAG TAP controller each time a system reset occurs. JP25 connects the TRST signal from the JTAG connection with the system reset signal RESET#.

Default Setting: Not fitted

1.5 Audio

STM3220F-EVAL evaluation board supports stereo audio play thanks to an audio DAC CS43L22 connected to both I2S2 port and one channels of DAC of microcontroller STM32F207IFT6. The CS43L22 can be configured via I2C1. The automatically switch between the speaker and headphone is supported by both CS43L22 and audio jack with plug detection pin.

1.6 EEPROM

A 64KBit EEPROM connected to I2C1 bus of STM32F207IFT6.

Table 5 EEPROM Related Jumpers

Jumper Description JP24

The EEPROM is in Write protection mode when JP24 is closed. Default Setting: Not fitted

1.7 CAN

STM3220F-EVAL evaluation board supports two channels of CAN2.0A/B complaint CAN bus communication based on 3.3V CAN transceiver. The two CAN bus are disabled and disconnected by jumpers from relevant STM32F207IFT6 IO’s which are shared with FSMC and USB OTG HS. The jumper JP14 and JP15 must be re-set to enable CAN1 while JP10 and JP11 must be re-set to enable CAN2 as listed in table 6 and table 7.

The High-speed mode, standby mode and slope control mode are available and can be selected by setting JP12 for CAN1 and JP7 for CAN2.

Page 9

STM3220F-EVAL Board

Qing SHAO Page 9 03/06/2009

Table 6 CAN1 related Jumpers

Jumper Description

CAN1 transceiver is working in standby mode when JP12 is set as shown to the right:

CAN1 transceiver is working in high-speed mode when JP12 is set as shown to the right: (default setting)

JP12

CAN1 transceiver is working in slope control mode when JP12 is open.

JP13

CAN1 terminal resistor is enabled when JP13 is fitted. Default setting: Not fitted

JP14

CAN1_TX is connected to PD1 and all peripherals connected to FSMC (LCD, PSRAM & OneNAND) are disabled when JP14 is closed.

Default setting: Not fitted

JP15

CAN1_RX is connected to PD0 and all peripherals connected to FSMC (LCD, PSRAM & OneNAND) are disabled when JP15 is closed.

Default setting: Not fitted

Table 7 CAN2 related Jumpers

Jumper Description

CAN2 transceiver is working in standby mode when JP7 is set as shown to the right:

CAN2 transceiver is working in high-s pe ed m ode whe n JP7 is set as shown to the right: (default setting)

JP7

CAN2 transceiver is working in slope control mode when JP7 is open.

JP9

CAN2 terminal resistor is enabled when JP9 is fitted. Default setting: Not fitted

JP10

CAN2_TX is connected to PB13 and USB OTG HS is disabled when JP10 is closed. JP10 must be open for USB OTG HS application.

Default setting: Not fitted

JP11

CAN2_RX is connected to PB5 and USB OTG HS is disabled when JP11 is closed. JP11 must be open for USB OTG HS application.

Default setting: Not fitted

1 2 3

Page 10

STM3220F-EVAL Board

Qing SHAO Page 10 03/06/2009

1.8 RS232 & IrDA

Both RS232 and IrDA communication is supported by D-type 9-pins RS232 connectors CN16 and IrDA transceiver U11 which are connected to USART3 of STM32F207IFT6 on STM3220F-EVAL evaluation board. Two signals, Bootloader_BOOT0 and Bootloader_RESET, are added on RS232 connector for ISP support.

RS232 or IrDA can be selected by setting of JP22:

Table 8 RS232 & IrDA Related Jumpers

Jumper Description

USART3_RX is connected to IrDA transcei ver and Ir D A com munication is enabled when JP22 is set as shown to the right:

USART3_RX is connected to RS232 transceiver and RS232 communication is enabled when JP22 is set as shown to the right(Default setting):

JP22

JP22 must be set to open to enable MicroSD card witch shares same IOs with RS232.

1.9 Motor Control

STM3220F-EVAL evaluation board supports three-phase brushless motor control via a 34pins connector CN17, which provides all required control and feedback signals to and from motor power-driving board. Available signals on this connector includes emergency stop, motor speed, 3 phase motor current, bus voltage, Heatsink temperature coming from the motor driving board and 6 channels of PWM control signal going to the motor driving circuit.

JP2 allows to choose two kind to synchronization methods for PFCs (Power Factor Correction).

The I/O pins used on Motor control connector CN17 are multiplexed with some peripherals on the board; either motor control connector or multiplexed peripherals can be enabled by setting of jumpers JP4, JP20 and JP3:

Table 9 Motor Control Related Jumpers

1 2 3

Page 11

STM3220F-EVAL Board

Qing SHAO Page 11 03/06/2009

Note: MicroSD card must be removed from CN6 for Motor control application.

1.10 Smart Card

STMicroelectronics Smart card interface chip ST8024 is used on STM3220F-EVAL board for asynchronous 3V and 5V smart cards. It performs all supply protection and control functions based on the connections with STM32F207IFT6 listed in table 10:

Table 10 Connection between ST8024 and STM32F207IFT6

Signals of ST8024

Description Connect to

STM32F207IFT6

5V/3V

Smart card power supply selection pin.

PH15

I/OUC

MCU data I/O line

PC6

XTAL1

Crystal or external clock input

PG7

OFF

Detect presence of a card

, Interrupt to MCU, share same

pin with Motor controller

PF6

RSTIN

Card Reset Input from MCU

PF7

CMDVCC

Start activation sequence input (Active Low), share same pin with I2S DAC and Motor control

PG12

Jumper Description

JP2

JP2 allows to have a PFC synchronization signal redirected to the timer 3 input capture 2 pin, additionally to the timer3 external trigger input.

Default setting: Not Fitted

JP1

JP1 should be kept on open when encoder signal is input from pin31 of CN5 while it should be kept on close when analog signal is from pin31 of CN5 for special motor.

Default setting: Not Fitted

SB3

Solder bridge SB3 is closed by default to connect BNC connector and Motor control connector to PF8. For external analog input connected to TP3 and TP4, SB3 may be disconnected.

It allows to connect an analogue source to ADC for accuracy and reliability evaluation with minimum noise induced by components on the board.

Default setting: close

Jumper Description

Multiplexed peripherals

JP20

MC_BusVoltage is connected to PF6 when JP20 is set as shown to the right:

SmartCard_OFF is connected to PF6 when JP20 is set as show to the right (Default setting):

JP3

MC_HeatsinkTemperature is connected to PF7 when JP3 is closed. JP3 must be open for Smart card.

Default setting: Not Fitted

Smart card

JP4

MC_EmergencySTOP is connected to PI4 when JP4 is closed.

Default setting: Not Fitted

Camera

module

connected

to CN15

1 2 3

Page 12

STM3220F-EVAL Board

Qing SHAO Page 12 03/06/2009

Smart card shares some IO’s with Motor control connector CN5 and I2S bus for Audio.

Some jumper has to be re-configured to enable Smartcard as listed below:

Table 11 Smartcard Related Jumpers

Jumper Description

JP21

SmartCard_IO is connected to PC6 when JP21 is closed. JP21 must be open for Audio DAC connected to I2S.

Default setting: Not Fitted

JP3 & JP20 Description of JP3 and JP20 is in chapter 1.9 Motor control.

1.11 MicroSD card

The 1GByte or more MicroSD card connected to SDIO of STM32F207IFT6 is available on the board. MicroSD card Detection is managed by standard IO port PH13. MicroSD card shares same IO’s with Motor control & RS232. The jumper JP22 must be open and Motor control connector (CN6) must be disconnected for MicroSD card.

Table 12 MicroSD card related Jumpers

Jumper Description

JP22 Description of JP22 is in chapter 1.8 RS232 & IrDA.

1.12 MEMS

A ST MEMS device LIS302DL is connected to I2C1 bus of STM32F207IFT6 on the board.

1.13 Analog Input

One BNC connectors CN17 is connected to PF8 of STM32F207IFT6 as external analog input when Motor control connector is not used. The 50 ohm terminal resistor can be enabled by closing of solder bridge SB8. A low pass filter can be implemented for BNC connector by replacing of R74 and C59 with right value of resister and capacitor as requested by end user’s application. Note: For ADC accuracy measurement please use TP3 & TP4 as described in table 9 on chapter 1.9

There are also 2 analog signals available on the board:

1. 10K ohm potentiometer RV1 connected to PC2 via jumper JP23.

2. IDD measurement output signal connected to PF9 for power consumption test in RUN, SLEEP and STOP mode.

Table 13 Potentiometer related Jumpers

Jumper Description

JP23

Potentiometer RV1 is connected to PC2 when JP23 is closed. JP23 must be open for Ethernet application.

Default setting: Not fitted

SB8

The 50ohm terminal resistor is enabled when SB8 is closed. Default setting: open

Page 13

STM3220F-EVAL Board

Qing SHAO Page 13 03/06/2009

1.14 USB OTG FS

STM3220F-EVAL evaluation board support USB OTG full speed communication via a USB Micro-AB connector (CN8) and USB power switch (U1) connected to VBUS. The evaluation board can be powered by this USB connection at 5V DC with 500mA current limitation.

The LED LD6 will be light when power switch (U1) is ON and STM3220F-EVAL works as a USB host or if VBUS is powered by another USB host when STM3220F-EVAL works as a USB device. The LD5 will be light when over-current is occurred.

1.15 Ethernet

STM3220F-EVAL evaluation board support 10M/100M Ethernet communication by a PHY DP83848CVV (U5) and integrated RJ45 connector (CN7). Both MII and RMII interface mode are supported and can be selected by setting of jumpers JP5, JP6 and JP8 as listed below:

Table 14 Ethernet Related Jumpers and solder bridges

Jumper Description

JP8

JP8 is used to select MII or RMII interface mode. MII is enabled when JP8 is open while RMII interface mode is enabled when JP8 is close.

Default setting: Not Fitted JP6 should be set as shown to the right when MII interface mode is enabled(Default setting):

JP6

JP6 should be set as shown to the right when RMII interface mode is enabled:

25MHz clock for MII or 50MHz clock for RMII is provided by MCO at PA8 when JP5 is set as shown to the right (Default setting):

25MHz clock is provided by external crystal X1 (for MII interface mode only) when JP5 is set as shown to the right:

JP5

JP5 has to be kept open when clock is provided by external oscillator U3 (not fit by default)

JP23 Description of JP23 is in chapter 1.13 Analog Input.

SB1

SB1 is used to select clock source only for RMII mode, the clock from MCO is connected to RMII_REF_CLK when SB1 is closed.

Default setting: open

SB2

SB2 is used to select clock source only for RMII mode, the clock from pin25 of Ethernet PHY U5 is connected to RMII_REF_CLK when SB2 is closed.

Default setting: close

A tes tpoint TP2 is available on the board for PTP_PPS feature test, it can be used only when JP11 is kept on open. (Note: there are no problem of conflict between PTP_PPS output &

ULPI data bus, pls. refer to 6.1.9.3 interface protection of USB3300. TBC)

1 2 3

Page 14

STM3220F-EVAL Board

Qing SHAO Page 14 03/06/2009

1.16 USB OTG HS

STM3220F-EVAL evaluation board support USB OTG High speed communication via a USB Micro-AB connector (CN9), USB High speed PHY (U8) and USB power switch (U4) connected to VBUS. The evaluation board can be powered by this USB connector (CN9) at 5V DC with 500mA current limitation.

The LED LD7 will be light when power switch (U4) is ON and STM3220F-EVAL works as a USB host or if VBUS is powered by another USB host when STM3220F-EVAL works as a USB device. The LD8 will be light when over-current is occurred.

The USB ULPI bus is shared with CAN2 bus, the JP10 and JP11 must be kept on open for USB OTG HS.

1.17 Camera Module

A 1.3Mega Pixel camera module is connected to DCMI bus of STM32F207IFT6 and shares same IOs with motor control connector. JP4 must be kept on open for Camera module application.

Table 15 Camera module Related Jumpers

Jumper Description

JP26

The camera module is in power down mode when JP26 is closed. Default setting: Not Fitted

JP4 Description of JP4 is in chapter 1.9 Motor control.

1.18 PSRAM and OneNAND

The 4Mbit PSRAM and 512Mbit OneNAND are connected to FSMC bus of STM32F207IFT6 which shares same IO’s with CAN1 bus. The JP14 and JP15 must be kept on open for PSRAM, OneNAND and LCD application.

1.19 Development and Debug support

The two debug connectors available on STM3220F-EVAL evaluation board are:

1. CN14, standard 20-pins JTAG interface connector that is compliant with debug tools of ARM7 and ARM9.

2. CN13, SAMTEC 20-pins connector FTSH-110-01-L-DV for both SWD and Trace that is compliant with ARM CoreSight debug tools.

1.20 Display and Input devices

The 3.2” TFT color LCD connected to FSMC bus and 4 general purpose color LED’s (LD 1,2,3,4) are available as display device. A touch screen connected to IO expander (U24), 4direction joystick with selection key, general purpose button (B4), Wakeup button (B2) and Tamper detection button (B3) are available as input devices.

Table 16 LCD modules

3.2” TFT LCD with touch screen (CN16) Pin on CN16

Pin name Pin connection Pin on

CN16

Pin name Pin connection

1 CS FSMC_NE3 (PG10) 18 PD14 FSMC_D12 2 RS FSMC_A0 19 PD14 FSMC_D13 3 WR/SCL FSMC_NWE 20 PD16 FSMC_D14 4 RD FSMC_NOE 21 PD17 FSMC_D15 5 RESET RESET# 22 BL_GND GND 6 PD1 FSMC_D0 23 BL_Control +5V 7 PD2 FSMC_D1 24 VDD +3V3 8 PD3 FSMC_D2 25 VCI +3V3

Page 15

STM3220F-EVAL Board

Qing SHAO Page 15 03/06/2009

9 PD4 FSMC_D3 26 GND GND 10 PD5 FSMC_D4 27 GND GND 11 PD6 FSMC_D5 28 BL_VDD +5V 12 PD7 FSMC_D6 29 SDO NC 13 PD8 FSMC_D7 30 SDI NC 14 PD10 FSMC_D8 31 XL IO expander

U24

15 PD11 FSMC_D9 32 XR IO expander

U24

16 PD12 FSMC_D10 33 YD IO expander

U24

17 PD13 FSMC_D11 34 YU IO expander

U24

1.21 IDD measurement and comparator

For IDD measurement the circuit below is implemented on STM3220F-EVAL.

Figure 4: STM3220F-EVAL IDD measurement circuit

In Run mode, IDD current is measured thanks to TSC101BILT (U14) connected to the 1ohm shunt resistor. In this case IDD_CNT_EN remains at high level during measurement and JP16 jumper must be removed.

In Halt mode, the operational amplifier TSC101BILT (U14) is connected on the 1Kohm shunt resistor. To measure a current corresponding to the Halt mode the procedure is:

1. Configure ADC to measure voltage on IDD_measurement pin.

2. Configure PA0 as interrupt input on falling edge

3. Enter in Halt or active Halt mode with IDD_CNT_EN Low

4. LP_WAKEUP falling edge wakeup the MCU after 100ms

5. start ADC conversion as soon as possible after wakeup in order to measure the voltage corresponding to Sleep mode on 1uF capacitor

6. Reset the counter by programming IDD_CNT_EN High in less than 50mS after the wakeup to avoid 1Kohm to be connected later on VDD_MCU

In Halt mode, the 1K resistor is connected when T1 become off after entering in Halt mode. Q13 output of the counter allows connecting the 1K when the current IDD becomes very low. The measurement timing is given below:

Figure 5: STM3220F-EVAL IDD Halt mode measurement timing diagram

Page 16

STM3220F-EVAL Board

Qing SHAO Page 16 03/06/2009

Halt mode IDD measurement timing

IDD_CNT_EN (PI8)

Q13= LOW_POWER_EN (T1 pin 3)

Q14n = Sw it ch contro l (U 15 pi n 4)

Run

150mS

Halt

Q14 = LP_WAKEUP (PA0)

300mS

Wake-up Clear C N T

450mS

IDD Measu re

MCU mode

The halt mode measurement procedure can be used in Halt mode and slow or fast active Halt modes if the IDD current do not exceed 60uA else the Run measurement procedure need to be used up to 60mA.

Page 17

STM3220F-EVAL Board

Qing SHAO Page 17 03/06/2009

2. Connector

2.1 Daughter board extension connector CN1,2,3 and CN4

Four male headers CN1,2,3 and CN4 can be used to connect with daughter board or standard wrapping board to STM3220F-EVAL evaluation board. All total 140 GPI/Os are available on it.

Each pin on CN1,2,3 and CN4 can be used by a daughter board after disconnecting it from the corresponding function block on STM3220F-EVAL evaluation board. Please refer to table

17 to table 20 for detail.

Table 17 Daughter board extension connector CN1

Pin Description Alternative

Function

How to disconnect with function block on STM3220F-EVAL board

1 GND - 3 PE3 Trace_D0 5 PE5 Trace_D2 7 PI8 IDD_CNT_EN 9 PC14 OSC32_IN SB4 open 11 PC15 OSC32_OUT SB5 open 13 PI10 MII_RX_ER Remove RS3 15 PF0 FSMC_A0 17 PF2 FSMC_A2 19 GND - 21 PF5 FSMC_A5 23 PF7 SmartCard_RS

T &MC

JP3 open

25 PF9 IDD_Measure

ment & MC

Remove R82

Disconnect Motor Control board from CN5 27 PH0 OSC_IN SB6 open 29 PC0 ULPI_STP 31 PC1 MII_MDC 33 PC3 MII_TX_CLK Remove RS5 35 PA0 WakeUP Remove R139 37 PA2 MII_MDIO 39 GND - 41 PH4 ULPI_NXT Can not be used on daughter board 43 NC - 45 NC - 47 EMU_3V3 - 49 EMU_5V - 2 PE2 Trace_CLK 4 PE4 Trace_D1 6 PE6 Trace_D3 8 PC13 Anti-Tamper Remove R143 10 GND - 12 PI9 LED3 Remove R141 14 PI11 ULPI_DIR Can not be used on daughter board 16 PF1 FSMC_A1 18 PF3 FSMC_A3 20 PF4 FSMC_A4 22 PF6 SmartCard_OF

F & MC

JP20 open 24 PF8 MC Disconnect Motor Control board from CN5

26 PF10 MC Disconnect Motor Control board from CN5 28 PH1 OSC_OUT SB7 open

Page 18

STM3220F-EVAL Board

Qing SHAO Page 18 03/06/2009

30 GND - 32 PC2 MII_TXD2 &

potentiometer

JP23 open 34 VREF+ - -

36 PA1 MII_RX_CLK JP6 open 38 PH2 MII_CRS Remove RS3 40 PH3 MII_COL Remove RS3 42 PH5 OTG_FS_Pow

erSwitchOn

Remove R18 44 NC - -

46 NC - 48 APP_3V3 - 50 GND - -

Table 18 Daughter board extension connector CN2

Pin Description Alternative

Function

How to disconnect with function block

on STM3220F-EVAL board

1 GND - 3 PA3 ULPI_D0 5 PA5 ULPI_CLK Can not be used on daughter board 7 PA7 MII_RX_DV Remove RS2, JP8 open 9 PC5 MII_RXD1 Remove RS2 11 PB0 ULPI_D1 13 PB2 BOOT1 15 PF12 FSMC_A6 17 PF14 FSMC_A8 19 GND - 21 PG1 FSMC_A11 23 PE8 FSMC_D5 25 PE10 FSMC_D7 27 PE12 FSMC_D9 29 PE14 FSMC_D11 31 PE15 FSMC_D12 33 PB11 ULPI_D4 35 PH7 MII_RXD3 Remove RS3 37 PH9 DCMI_D0 Remove camera module from CN15 39 GND - 2 APP_VCC - 4 PA4 Audio_DAC_O

Remove R115 6 PA6 DCMI_PIXCK Remove camera module from CN15

8 PC4 MII_RXD0 Remove RS2 10 GND - 12 PB1 ULPI_D2 14 PF11 OTG_FS_Over

current

Remove R15 16 PF13 FSMC_A7 -

18 PF15 FSMC_A9 20 PG0 FSMC_A10 22 PE7 FSMC_D4 24 PE9 FSMC_D6 26 PE11 FSMC_D8 28 PE13 FSMC_D10 30 GND - 32 PB10 ULPI_D3 34 PH6 MII_RXD2 Remove RS5 36 PH8 DCMI_HSYNC

& MC

Remove camera module from CN15

Disconnect Motor Control board from CN5 38 PH10 DCMI_D1 &MC Remove camera module from CN15

Page 19

STM3220F-EVAL Board

Qing SHAO Page 19 03/06/2009

Disconnect Motor Control board from CN5 40 PH11 DCMI_D2 &MC Remove camera module from CN15

Disconnect Motor Control board from CN5

Table 19 Daughter board extension connector CN3

Pin Description Alternative

Function

How to disconnect with function block

on STM3220F-EVAL board

1 GND - 3 PI1 I2S_CK 5 PH15 SmartCard_3/5

V & MC

Disconnect Motor Control board from CN5 7 PH13 MicroSDCard_

defect & MC

Remove MicroSD card from CN6

Disconnect Motor Control board from CN5 9 PC13 Anti-Tamper Remove R143 11 RESET# Reset button 13 PA11 OTG_FS_DM Remove R17 15 PA9 VBUS_FS Remove USB cable from CN8

Remove R18 17 PC9 MicroSDCard_

D1 & MC

Remove MicroSD card from CN6

Disconnect Motor Control board from CN5 19 EMU_5V - 21 PC6 I2S_MCK &

SmartCard_IO

JP21 open 23 PG7 SmartCard_CLK 25 PG5 FSMC_A15 -

27 PG3 FSMC_A13 29 PD15 FSMC_D1 31 PD14 FSMC_D0 33 PD12 FSMC_A17 35 PD10 FSMC_D15 37 PD8 FSMC_D13 39 GND - 41 PB13 ULPI_D6 &

CAN2_TX

43 PH12 DCMI_D3 &

Remove camera module from CN15

Disconnect Motor Control board from CN5 45 NC - 47 EMU_3V3 - 49 EMU_5V - 2 PI2 IO_Expandor_I

Remove R136 4 PI0 I2S_CMD -

6 PH14 DCMI_D4 &

Remove camera module from CN15

Disconnect Motor Control board from CN5 8 PA13 TMS/SWDIO 10 GND - 12 PA12 OTG_FS_DP Remove R19 14 PA10 OTG_FS_ID Remove R21 16 PA8 MCO JP5 open 18 PC8 MicroSDCard_

D0 & MC

Remove MicroSD card from CN6

Disconnect Motor Control board from CN5 20 PC7 LED4 Remove R140 22 PG8 LED2 Remove R154 24 PG6 LED1 Remove R155 26 PG4 FSMC_A14 28 PG2 FSMC_A12 30 GND - -

Page 20

STM3220F-EVAL Board

Qing SHAO Page 20 03/06/2009

32 PD13 MC Disconnect Motor Control board from CN5 34 PD11 FSMC_A16 36 PD9 FSMC_D14 38 PB15 OneNAND_INT Remove R53 40 PB14 MII_INT Remove R41 42 PB12 ULPI_D5 44 NC - 46 NC - 48 APP_3V3 - 50 GND - -

Table 20 Daughter board extension connector CN4

Pin Description Alternative

Function

How to disconnect with function block

on STM3220F-EVAL board

1 GND - 3 PI6 DCMI_D6 &

Remove camera module from CN15

Disconnect Motor Control board from CN5 5 PI4 DCMI_D5 &

Remove camera module from CN15

JP4 open 7 PE0 FSMC_BL0 9 PB8 MII_TXD3 &

Remove RS5

Disconnect Motor Control board from CN5 11 BOOT0 BOOT0 13 PB6 I2C1_SCK Remove R103 15 PB4 TRST 17 PG15 User button Remove R150 19 GND - 21 PG12 SmartCard_C

MDVCC

Remove R128 23 PG10 FSMC_NE3 Remove LCD board MB785 from CN19

25 PD7 FSMC_NE1 Remove R52 27 PD5 FSMC_NWE 29 PD3 FSMC_CLK 31 PD2 MicroSDCard_

CMD

33 PD0 FSMC_D2 &

CAN1_RX

JP15 open 35 PC11 MicroSDCard_

D3 & RS232/IrDA_R X

JP22 open

Remove MicroSD card from CN6

37 PA15 TDI 39 GND - 2 PI7 DCMI_D7 &

Remove camera module from CN15

Disconnect Motor Control board from CN5 4 PI5 DCMI_VSYNC

& MC

Remove camera module from CN15

Disconnect Motor Control board from CN5 6 PE1 FSMC_BL1 8 PB9 I2C1_SDA Remove R111 10 GND - 12 PB7 FSMC_NL 14 PB5 ULPI_D7 &

CAN2_RX

JP11 open

16 PB3 TDO/SWO 18 PG14 MII_TXD1 Remove RS6 20 PG13 MII_TXD0 Remove RS6 22 PG11 MII_TX_EN Remove RS6 24 PG9 FSMC_NE2 Remove R47 26 PD6 FSMC_NWAIT Remove R54

Page 21

STM3220F-EVAL Board

Qing SHAO Page 21 03/06/2009

28 PG4 FSMC_A14 30 GND - 32 PD1 FSMC_D3 &

CAN1_TX

JP14 open 34 PC12 MicroSDCard_

CLK

Remove MicroSD card from CN6 36 PC10 MicroSDCard_

D2 & RS232/IrDA_T X

Remove MicroSD card from CN6

38 PA14 TCK/SWCLK 40 PI3 I2S_DIN -

Note: The 0ohm resister will added on PCB rev.B for PI11(ULPI_DIR), PA5(ULPI_CLK) & PH4(ULPI_NXT) usage on daughter board. For ULPI[0..7], it’s in input status for PHY USB3300 by default, so, 0ohm resister is not needed, TBC.

2.2 Motor control connector CN5

Figure 6 Motor Control connector CN5

Table 21 Motor Control connector CN5

Description Pin of

STM32F207IFT6

Pin number of CN17

Pin of STM32F207IFT6

Description

EMERGENCY STOP

PI4 1 2 GND

PWM-UH PI5 3 4 GND PWM-UL PH 5 6 GND PWM-VH PI6 7 8 GND PWM-VL PH14 9 10 GND PWM-WH PI7 11 12 GND PWM-WL PH15 13 14 PF6 BUS

VOLTAGE PHASE A CURRENT

PF8 15 16 GND

PHASE B CURRENT

PF9 17 18 GND

PHASE C CURRENT

PF10 19 20 GND

NTC BYPASS RELAY

PH8 21 22 GND

DISSIPATIVE BRAKE PWM

PC8 23 24 GND

+5V power +5V 25 26 PF7 Heatsink

Viewed from above PCB

33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2

Page 22

STM3220F-EVAL Board

Qing SHAO Page 22 03/06/2009

temperature PFC SYNC PH10 and PH11 27 28 VDD_Micro PFC PWM PH12 29 30 GND Encoder A PB8 31 32 GND Encoder B PD13 33 34 PC9 Encoder

Index

2.3 MicroSD connector CN6

Figure 7 MicroSD connector CN6

Table 22 MicroSD connector CN6

Pin number Description Pin

number

Description

1 SDIO_D2 (PC11) 5 SDIO_CLK (PC12) 2 SDIO_D2 (PC10) 6 Vss/GND 3 SDIO_CMD (PD2) 7 SDIO_D0 (PC9) 4 +3V3 8 SDIO_D1 (PC8) 9 MicroSDcard_detect (PH13)

2.4 Ethernet RJ45 connector CN7

Figure 8 Ethernet RJ45 connector CN7

Viewed from front

Page 23

STM3220F-EVAL Board

Qing SHAO Page 23 03/06/2009

Table 23 RJ45 connector CN7

Pin number Description Pin

number

Description

TxData+

TxData-

RxData+

Shield

RxData-

Shield

2.5 USB OTG FS Micro-AB connector CN8

Figure 9 USB OTG FS Micro-AB connector CN8

Table 24 USB OTG FS Micro-AB connector CN8

Pin number Description Pin number Description

1 VBUS (PA9) 4 ID (PA10) 2 D- (PA11) 5 GND 3 D+ (PA12)

2.6 USB OTG HS Micro-AB connector CN9

Figure 10 USB OTG HS Micro-AB connector CN9

Table 25 USB OTG HS Micro-AB connector CN9

Pin number Description Pin number Description

1 VBUS 4 ID 2 D- 5 GND 3 D+

Viewed from front

Page 24

STM3220F-EVAL Board

Qing SHAO Page 24 03/06/2009

2.7 CAN D-type 9-pins male connector CN10(CAN2) & CN12(CAN1)

Figure 11 CAN D-type 9-pins male connector CN10 (CAN2) & CN12 (CAN1)

Table 26 CAN D-type 9-pins male connector CN10 (CAN2) & CN12 (CAN1)

Pin number Description Pin number Description

1,4,8,9 NC 7 CANH 2 CANL 3,5,6 GND

2.8 Audio connector CN11

A 3.5mm Stereo audio jack CN11 with plug-detection feature connected to audio DAC is available on STM3220F-EVAL board.

2.9 Trace debugging connector CN13

Figure 12 Trace debugging connector CN13

Table 27 Trace debugging connector CN13

Pin number Description Pin

number

Description

1 3.3V power 2 TMS/PA13 3 GND 4 TCK/PA14 5 GND 6 TDO/PB3 7 KEY 8 TDI/PA15 9 GND 10 RESET# 11 GND 12 TraceCLK/PE2 13 GND 14 TraceD0/PE3 or SWO/PB3 15 GND 16 TraceD1/PE4 or nTRST/PB4 17 GND 18 TraceD2/PE5 19 GND 20 TraceD3/PE6

Viewed from above PCB

Viewed from front

19 17 15 13 11 9 7 5 3 1

20 18 16 14 12 10 8 6 4 2

Page 25

STM3220F-EVAL Board

Qing SHAO Page 25 03/06/2009

2.10 JTAG debugging connector CN14

Figure 13 JTAG debugging connector CN14

Table 28 JTAG debugging connector CN14

Pin number Description Pin

number

Description

1 3.3V power 2 3.3V power 3 PB4 4 GND 5 PA15 6 GND 7 PA13 8 GND 9 PA14 10 GND 11 RTCK 12 GND 13 PB3 14 GND 15 RESET# 16 GND 17 DBGRQ 18 GND 19 DBGACK 20 GND

2.11 Camera module connector CN15

Figure 14 Camera module connector CN15

Table 29 Camera module connector CN15

Pin number Description Pin number Description

1 DGND 13 XCLK1 2 DGND 14 Y6(PI6) 3 SIO_D (PB9) 15 DGND 4 AVDD (2.8V) 16 Y5(PI4) 5 SIO_C (PB6) 17 PCLK (PA6) 6 RESET 18 Y4(PH14) 7 VSYNC (PI5) 19 Y0 (PH9) 8 PWDN 20 Y3(PH12) 9 HREF (PH8) 21 Y1(PH10) 10 DVDD (1.8V) 22 Y2(PH11)

Viewed from front

Viewed from above PCB

19 17 15 13 11 9 7 5 3 1

20 18 16 14 12 10 8 6 4 2

Page 26

STM3220F-EVAL Board

Qing SHAO Page 26 03/06/2009

11 VOVDD (2.8V) 23 AGND 12 Y7(PI7) 24 AGND

2.12 RS232 connector CN16

Figure 15 RS232 connector CN16 with ISP support

Table 30 RS232 connector CN16 with ISP support

Pin number Description Pin

number

Description

1 Bootloader_RESET 6 NC 2 RS232_RX (PC11) 7 NC 3 RS232_TX (PC10) 8 Bootloader_BOOT0 4 NC 9 NC 5 GND

2.13 Analog input connector CN17

Figure 16 Analog input connector CN17

Table 31 Analog input connector CN17

Pin number Description Pin

number

Description

1 GND 4 GND 2 GND 5 Analog input PF8 3 GND

2.14 Power connector CN18

Your STM3220F-EVAL evaluation board can be powered from a DC 5V power supply via the external power supply jack (CN18) shown in Figure17. The central pin of CN18 must be positive.

Figure 17 Power supply connector CN18

Viewed from front

Page 27

STM3220F-EVAL Board

Qing SHAO Page 27 03/06/2009

2.15 TFT LCD connector CN19

One 34-pin male header CN19 is available on the board to connect LCD module board MB785. Please refer to chapter 1.20 for detail.

2.16 Smart card connector CN20

Figure 18 Smart card connector CN20

Table 32 Smart card connector CN20

Pin number

Description Pin

number

Description

1 VCC 5 GND 2 RST 6 NC 3 CLK 7 I/O 4 NC 8 NC 17 Detection pin of card presence 18 Detection pin of card presence

Viewed from front

DC +5V

GND

Viewed from front

1 2 3 4

5 6 7 8

17 18

Page 28

STM3220F-EVAL Board

Qing SHAO Page 28 03/06/2009

3. Known limitations and bugs on PCB rev A

• When using MB760 adapter to connect the board to the STice some precautions need to be considered to avoid short-circuits between MB760 PCB and the daughter boards connectors CN2, CN3 and CN4 pins. An adhesive strip on bottom side of MB760 used as isolation may be damaged when the MB687 (flexPCB) is plugged on MB760 J2 connector. To avoid this issue it strongly recommended to connect first the MB687 to MB760 then to screw MB760 to MCU socket on evaluation board (MB786).

• On Mother board (MB786) Sheet 1 & 4 PB6 and PB9 are named respectively I2C2_SCL and I2C2_SDA. Actually PB6 and PB9 alternate function are on I2C1

• DCD signal on RS232 connector is connected to board RESET for bootloader applications. It is not possible to disconnect this signal from RESET directly on the board so when using RS232 interface the host need to maintain DCD signal low or the corresponding pin needs to be disconnected on RS232 cable or connector.

• BOOT0 and BOOT1 switches are swapped on the silkscreen.

• Joystick is rotated by 180° compared to signals names on the schematic. Therefore a

workaround is neede d in th e s of twar e to s w ap up with do wn an d right with left sig nals .

Page 29

STM3220F-EVAL Board

Qing SHAO Page 29 03/06/2009

4. Schematic

Page 30

STM3220F-EVAL Board

Qing SHAO Page 30 03/06/2009

Page 31

STM3220F-EVAL Board

Qing SHAO Page 31 03/06/2009

Page 32

STM3220F-EVAL Board

Qing SHAO Page 32 03/06/2009

Page 33

STM3220F-EVAL Board

Qing SHAO Page 33 03/06/2009

Page 34

STM3220F-EVAL Board

Qing SHAO Page 34 03/06/2009

Page 35

STM3220F-EVAL Board

Qing SHAO Page 35 03/06/2009

Page 36

STM3220F-EVAL Board

Qing SHAO Page 36 03/06/2009

Page 37

STM3220F-EVAL Board

Qing SHAO Page 37 03/06/2009

Page 38

STM3220F-EVAL Board

Qing SHAO Page 38 03/06/2009

Page 39

STM3220F-EVAL Board

Qing SHAO Page 39 03/06/2009

Page 40

STM3220F-EVAL Board

Qing SHAO Page 40 03/06/2009

Page 41

STM3220F-EVAL Board

Qing SHAO Page 41 03/06/2009

Page 42

STM3220F-EVAL Board

Qing SHAO Page 42 03/06/2009

Page 43

STM3220F-EVAL Board

Qing SHAO Page 43 03/06/2009

Page 44

STM3220F-EVAL Board

Qing SHAO Page 44 03/06/2009

Page 45

STM3220F-EVAL Board

Qing SHAO Page 45 03/06/2009

Page 46

STM3220F-EVAL Board

Qing SHAO Page 46 03/06/2009

Page 47

STM3220F-EVAL Board

Qing SHAO Page 47 03/06/2009

Page 48

STM3220F-EVAL Board

Qing SHAO Page 48 03/06/2009

Page 49

STM3220F-EVAL Board

Qing SHAO Page 49 03/06/2009

Appendix A STM3220F-EVA L IO Assignment

Pin No.

Pin Name STM3220F-EVAL IO Assignment

1 PE2 TRACE_CLK / FSMC_A23 2 PE3 TRACE_D0 / FSMC_A19 3 PE4 TRACE_D1 / FSMC_A20 4 PE5 TRACE_D2 / FSMC_A21 5 PE6 TRACE_D3 / FSMC_A22 6 VBAT VBAT

PI8- ANTI

TAMP2

IDD_CNT_EN

PC13-

ANTI_TAMP

ANTI-TAMPER_BUTTON

9 PC14-OSC32_IN 32K_OSC

PC15-

OSC32_OUT 32K_OSC 11 PI9 LED2 12 PI10 ETHER_RX_ER 13 PI11 USB_HS_DIR 14 VSS_13 15 VDD_13 16 PF0 FSMC_A0 17 PF1 FSMC_A1 18 PF2 FSMC_A2 19 PF3 FSMC_A3 20 PF4 FSMC_A4 21 PF5 FSMC_A5 22 VSS_5 23 VDD_5 24 PF6 MC_ADC3_4 pin 14 (Busvoltage) / SmartCard_OFF 25 PF7 MC_ADC3_4 pin 26 (Heatsinktemp) / SmartCard_RESET 26 PF8 MC_ADC3_6 pin 15 (Current A) / BNC 27 PF9 MC_ADC3_7 pin 17 (Current B) / ADC13_IDD_Measure 28 PF10 MC_ADC3_8 pin 19 (Current C) 29 PH0 - OSC_IN OSC_IN 30 PH1 - OSC_OUT OSC_OUT 31 NRST RESET_BUTTON 32 PC0 USB_HS_STP 33 PC1 ETHER_MDC 34 PC2 ETHER_TXD2 / POTENTIOMETER 35 PC3 ETHER_TX_CLK 36 VDD_12 37 VSSA 38 VREF+ 39 VDDA 40 PA0-WKUP WAKEUP_BUTTON 41 PA1 ETHER_RX_CLK 42 PA2 ETHER_MDIO 43 PH2 ETHER_CRS 44 PH3 ETHER_COL

Page 50

STM3220F-EVAL Board

Qing SHAO Page 50 03/06/2009

45 PH4 USB_HS_NXT 46 PH5 USB_FS_POWER_ON 47 PA3 USB_HS_D0 48 VSS_4 49 VDD_4 50 PA4 Audio_DAC_OUT 51 PA5 USB_HS_CK 52 PA6 CAM_PIXCK 53 PA7 ETHER_DV 54 PC4 ETHER_RXD0 55 PC5 ETHER_RXD1 56 PB0 USB_HS_D1 57 PB1 USB_HS_D2 58 PB2 BOOT1 / 59 PF11 USB_FS_OVERCURRENT 60 PF12 FSMC_A6 61 VSS6 62 VDD_6 63 PF13 FSMC_A7 64 PF14 FSMC_A8 65 PF15 FSMC_A9 66 PG0 FSMC_A10 67 PG1 FSMC_A11 68 PE7 FSMC_D4 69 PE8 FSMC_D5 70 PE9 FSMC_D6 71 VSS_7 72 VDD_7 73 PE10 FSMC_D7 74 PE11 FSMC_D8 75 PE12 FSMC_D9 76 PE13 FSMC_D10 77 PE14 FSMC_D11 78 PE15 FSMC_D12 79 PB10 USB_HS_D3 80 PB11 ULPI_D4 81 VCAP1 82 VDD_1 83 PH6 ETHER_RXD2 84 PH7 ETHER_RXD3 85 PH8 CAM_HSYNC / MC_NTC_bypass 86 PH9 CAM_D0 87 PH10 CAM_D1 / MC_TIM5_ETR pin 27 (PFC SYNC) 88 PH11 CAM_D2 / MC_TIM3_CH2 pin 27 (PFCSYNC) 89 PH12 CAM_D3 / TIM5_CH3 pin 29 (PFCPWM) 90 VSS_14 91 VDD_14 92 PB12 ULPI_D5 93 PB13 ULPI_D6 / CAN2_TX 94 PB14 ETHER_INT 95 PB15 OneNAND_INT 96 PD8 FSMC_D13 97 PD9 FSMC_D14 98 PD10 FSMC_D15 99 PD11 FSMC_A16

Page 51

STM3220F-EVAL Board

Qing SHAO Page 51 03/06/2009

100 PD12 FSMC_A17 101 PD13 MC_TIM4_CH2 pin 33 (EnB) 102 VSS_8 103 VDD_8 104 PD14 FSMC_D0 105 PD15 FSMC_D1 106 PG2 FSMC_A12 107 PG3 FSMC_A13 108 PG4 FSMC_A14 109 PG5 FSMC_A15 110 PG6 LED0 111 PG7 SmartCard_CK 112 PG8 LED1 113 VSS_9 114 VDD_9 115 PC6 SmartCard_IO / Audio_I2S_ MCK 116 PC7 LED3 117 PC8 SDIO_D0/ MC_TIM3_CH3 pin23 (Dissipative Brake) 118 PC9 SDIO_D1 / MC_TIM5_CH3 pin 34 (Index) 119 PA8 MCO 120 PA9 USB_FS_VBUS 121 PA10 USB_FS_ID 122 PA11 USB_FS_DM 123 PA12 USB_FS_DP 124 PA13 JTAG_TMS 125 VCAP2 126 VSS 2 127 VDD_2 128 PH13 MC_TIM8_CH1N pin 5 (UL) / Usdcard detect 129 PH14 CAM_D4 / MC_TIM8_CH2N pin 9 (VL) 130 PH15 MC_TIM8_CH3N pin 13 (WL) / SmartCard_3/5V 131 PI0 Audio_I2S_WS 132 PI1 Audio_I2S_CK 133 PI2 Expander_INT 134 PI3 Audio_I2S_DOUT 135 VSS_15 136 VDD_15 137 PA14 JTAG_TCK 138 PA15 JTAG_TDI 139 PC10 SDIO_D2 / RS232_TX 140 PC11 SDIO_D3 / RS232_RX 141 PC12 SDIO_CK 142 PD0 FSMC_D2 / CAN1_RX 143 PD1 FSMC_D3 / CAN1_TX 144 PD2 SDIO_CMD 145 PD3 FSMC_CLK 146 PD4 FSMC_NOE 147 PD5 FSMC_NWE 148 VSS_10 149 VDD_10 150 PD6 FSMC_NWAIT 151 PD7 FSMC_NE1 152 PG9 FSMC_NE2 153 PG10 FSMC_NE3 154 PG11 ETHER_TXEN

Page 52

STM3220F-EVAL Board

Qing SHAO Page 52 03/06/2009

155 PG12 SmartCard_CMDVCC 156 PG13 ETHER_TXD0 157 PG14 ETHER_TXD1 158 VSS_11 159 VDD_11 160 PG15 USER_BUTTON 161 PB3 JTAG_TDO 162 PB4 JTAG_TRST 163 PB5 CAN2_RX / ETHER_PPS_OUT / ULPI_D7 164 PB6 I2C1_SCL 165 PB7 FSMC_NL 166 BOOT0 BOOT0 167 PB8 ETHER_TXD3 / MC_TIM4_CH3 pin 31 (EnA) 168 PB9 I2C1_SDA 169 PE0 FSMC_NBL0 170 PE1 FSMC_NBL1 171 VSS_3 172 VDD_3 173 PI4 CAM_D5 / MC_TIM8_BKIN pin 1 (Stop) 174 PI5 CAM_VSYNC / MC_TIM8_CH1 pin 3 (UH) 175 PI6 CAM_D6 / MC_TIM8_CH2 pin 7 (VH) 176 PI7 CAM_D7 / MC_TIM8_CH3 pin 11 (WH)

Page 53

STM3220F-EVAL Board

Qing SHAO Page 53 03/06/2009

Appendix B Document Revision History

Table Document Revision History

Date

Version

Revision Details

09,Apr.2009

0.1

First version

28,May.2009

0.2

Updated after review and completed with PCB rev A known limitations

Page 54

STM3220F-EVAL Board

Qing SHAO Page 54 03/06/2009

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequ ences of use of such information nor for any infringement of paten t s or other rights of third parti es which may res ult from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.

The ST logo is a registered trademark of STMicroelectronics.

All other names are the property of their re spe ctive owners.

STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore Spain - Sweden - Switzerland - United Kingdom - United States

www.st.com