STDP2690
DP++
Output
SPDIF
Audio
DP Input
SPDIF
Transmitter
Clock
Generation
OCM, SPI
I2C to AUX
Bridge
I2C Slave
Video Format
Converter
Image
Capture
DP Dual Mode
Transmitter
DP
Receiver
AUX
DDC
Controller
DDC
Advanced DisplayPort to DisplayPort (dual mode) converter
Data brief
Features
■ DisplayPort® (DP) transmitter
– DP 1.2 compliant
– Link rate HBR2/HBR/RBR
– 1, 2, or 4 lanes
– AUX CH 1 Mbps
– HDMI/DVI operation with level translator
■ DisplayPort receiver
– DP 1.2 compliant
– Link rate HBR2/HBR/RBR
– 1, 2, or 4 lanes
– AUX CH 1 Mbps
■ SPDIF audio output
– 192 kHz/24 bits
– Compressed/LPCM
■ HDCP repeater with embedded keys
■ AUX to I2C bridge for EDID/MCCS pass
through
■ Spread spectrum on DisplayPort interface for
EMI reduction
■ Device configuration options
– SPI Flash
– I2C host interface
■ Deep color support
– RGB/YCC (4:4:4) – 16-bit color
– YCC (4:2:2/4:2:0) – 16-bit color
– Color space conversion – YUV to RGB and
RGB to YUV
■ Bandwidth
– Video resolution up to 4K x 2K @ 30 Hz;
1920 x 1080 @ 120 Hz
– Audio 7.1 Ch up to 192 kHz sample rate
■ Low power operation; active 500 mW, standby
25 mW
■ Package
–81 BGA (8 x 8 mm)
■ Power supply voltages
– 3.3 V I/O; 1.2 V core
Applications
■ Audio-video accessory (dongle) for
PC/notebooks and docking stations
■ Thunderbolt source and peripheral devices
June 2012 Doc ID 23267 Rev 1 1/8
For further information contact your local STMicroelectronics sales office.
www.st.com
8
Description STDP2690
1 Description
The STDP2690 is a high-speed DisplayPort to DisplayPort dual mode converter IC targeted
for applications such as audio-video accessories, docking stations, Thunderbolt storage
devices, etc. This device includes a VESA DP Standard Ver. 1.2 compliant receiver and
transmitter, implementing single link DisplayPort input and output ports comprising four Main
lanes, AUX CH, and HPD.
The STDP2690 uses ST's latest generation DisplayPort dual mode transmitter technology
that supports both DisplayPort and TMDS signal formats (DP++). DisplayPort receiver and
transmitter support HBR2 speed, a data rate of 5.4 Gbps per lane with a total bandwidth of
21.6 Gbps link rate. In addition, the transmitter is capable of supporting HDMI or single link
DVI output through a passive level translator (dongle). When configured as HDMI output,
this device supports link rate up to 2.97 Gbps that corresponds to a pixel rate of 297 MHz,
quite adequate for handling video timings up to FHD 120 Hz 3D formats. This device
delivers deep color video up to 16-bits per color at 1080p 60 Hz and lower video resolutions.
The STDP2690 allows audio transport from the source to desired audio rendering devices
over the DP++ output or through the SPDIF port. The audio signal from the source can be
routed simultaneously to DP++ and SPDIF output ports. For example, the STDP2690 allows
routing of any two audio channels on the SPDIF port, while transporting up to eight
channels on the DP++ port.
The STDP2690 supports RGB and YCbCr colorimetric formats with color depth of 16, 12,
10, and 8 bits. This device features HDCP 1.3 content protection scheme with an embedded
key option for secure transmission of digital audio-video content. It also operates as an
HDCP repeater for the downstream sink.
The AUX-to-I2C translator in the STDP2690 allows the upstream DisplayPort source to
access EDID and transfer MCCS commands to a downstream sink over the HDMI interface
when used with a level translator. The device has an on-chip microcontroller with SPI and
I2C host interface for system configuration purposes. STDP2690 can be configured with an
external SPI Flash for custom applications or simply configured from an external host
controller through I2C interface.
2/8 Doc ID 23267 Rev 1
STDP2690 Application overview
DIsplayPort
DP Main Lanes
DP++
STDP2690
SPI
Flash
27 MHz
Crystal
AUX CH
AUX CH
DP main lanes
MUX
DDC
2 Application overview
Figure 1. STDP2690 in PC/notebook accessory application
Doc ID 23267 Rev 1 3/8
Feature attributes STDP2690
3 Feature attributes
3.1 Input interface
● DP standard Ver. 1.2 compliant
● Main link configuration (SST format only, no MST format support)
– HBR2/HBR/RBR link rate
– 1, 2, or 4 lanes
● AUX CH: 1 Mbps Manchester transaction format
● HPD: IRQ_HPD assertion
● Video: EDID 1.4 and CEA861 video timing and formats from 24 to 48 bits/pixel in RGB
or YCC422 or YcC444 colorimetry
● Audio: DisplayPort 1.2 standard info frame packets andIEC60958/61937 type audio
stream packets ranging from 16 to 24 bits/sample, 32 to 192 kHz sample rates
3.2 Output interface
● DP++ transmitter interface featuring
– AC coupled DisplayPort Ver. 1.2 interface
– AC coupled HDMI 1.4 interface to external level translators
● DP main link configuration (SST format only, no MST format support)
– HBR2/HBR/RBR link rate
– 1, 2, or 4 lanes
● AUX CH: Manchester transaction format
● HPD: IRQ_HPD assertion
● Video: EDID 1.4 and CEA861 video timing and formats from 24 to 48 bits/pixel in RGB
or YCC422 or YcC444 colorimetry
● Audio: DisplayPort 1.2 standard info frame packets and IEC60958/61937 type audio
stream packets ranging from 16 to 24 bits/sample, 32 to 192 kHz sample rates
● HDMI link rate: 2.97 Gbps/data pair max
3.3 Deep color support
● RGB/YCC (4:4:4) – 16-bit color
● YCC (4:2:2/4:2:0) – 16-bit color
● Color space conversion – YUV to RGB and RGB to YUV
4/8 Doc ID 23267 Rev 1
STDP2690 Feature attributes
3.4 Supported video timings
● 4096 x 2160 (4K x 2K) 60 Hz: 24 bits/pixel (DP to DP only)
● 4096 x 2160 (4K x 2K) 24 Hz/30 Hz: 24 bits/pixel (DP to HDMI)
● 1920 x 1080 (FHD) 120 Hz: 24 bits/pixel
● 2560 x 1600 (WQXGA) 60 Hz: 24 bits/pixel
● Up to 1920 x 1080 (FHD) 60 Hz, 48, 36, 30 bits/pixel
● All compatible 3D formats defined in DP 1.2 and HDMI 1.4 specifications
● All standard CEA861 timing formats
3.5 Supported audio timings
● All audio formats as specified in DP 1.2 and HDMI 1.4 specifications
● SPDIF; 2-Ch LPCM, AC3, DTS, bit depth up to 24 bits, sample rate up to 192 kHz
3.6 Control channel interfaces
● AUX CH, I2C host interface, SPI (optional), and UART (UART for test/debug purposes
only)
3.7 HDCP 1.3 support
● Key sets for DP RX and DP/HDMI TX integrated in one-time programmable ROM
(OTP)
● Standalone HDCP repeater capability
3.8 Package
● 81 BGA (8 x 8 mm), 0.8 ball pitch
3.9 Power supply voltages
● 3.3 V I/O; 1.2 V core
3.10 ESD
● 2 KV HBM, 500 V CDM
Doc ID 23267 Rev 1 5/8
Ordering information STDP2690
4 Ordering information
Table 1. Order codes
Part number Description
STDP2690 81 BGA (8 x 8 mm)
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com
ECOPACK® is an ST trademark.
.
6/8 Doc ID 23267 Rev 1
STDP2690 Revision history
5 Revision history
Table 2. Document revision history
Date Revision Changes
05-Jun-2012 1 Initial release.
Doc ID 23267 Rev 1 7/8
STDP2690
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
8/8 Doc ID 23267 Rev 1
Loading...