ST SPC58XXADPT100S User Manual
SPC58XXADPT100S
Introduction
This document provides guidelines for describing, configuring and using the mini module SPC58XXADPT100S.
Figure 1. Overview of SPC58XXADPT100S mini module - top
UM2661
User manual
UM2661 - Rev 1 - January 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1 Overview
The SPC58XXADPT100S mini module is an evaluation board supporting STMicroelectronics SPC58xGxxE3,
SPC58xCxxE3, SPC58xBxxE3 microcontrollers in TQFP100 package with exposed pad down.
The SPC58XXADPT100S mini module is designed to be connected onto the SPC57xxMB motherboard, offering
a mechanism for easy customer evaluation of the supported devices, and facilitating hardware and software
development.
High density connectors provide the interface between the EVB and MCU daughter cards and help the
developers to evaluate all device peripherals.
This user manual provides information on using SPC58XXADPT100S mini module board and its hardware
features.
The mini module may be used as a stand-alone unit allowing access to the CPU, but no access to the I/O pins as
any motherboard peripherals.
UM2661
Overview
Figure 2. Overview of SPC58XXADPT100S mini module - bottom
1.1 Package contents
An SPC58XXADPT100S adapter package includes the following items:
• SPC58XXADPT100S mini module
UM2661 - Rev 1
page 2/23
• Mini CD with user manual
1.2 Supported device
The SPC58XXADPT100S mini module supports the following STMicroelectronics family of Microcontrollers in
TQFP100 package with exposed pad down:
• SPC58xGxxE3
• SPC58xCxxE3
• SPC584BxxE3
• SPC582BxxE3
UM2661
Supported device
UM2661 - Rev 1
page 3/23
2 SPC58XXADPT100S features
2.1 Mini module features
The SPC58XXADPT100S mini module board has the following features:
• Connector for external power supplies input: 5 V, 3.3 V, 1.25 V (for stand-alone mode)
• Reset button with driver and led indicator
• Socket for device in TQFP100 package with exposed pad down
• Debug ports:
– 34-pin SAMTEC connector for Nexus 2
– 14-pin header connector for JTAG port
• 40 Mhz crystal main oscillator with jumpers to optionally disconnect it
• 8 Mhz oscillator with jumpers to optionally disconnect it
• Clock input through SMA connector to optionally disconnect it
• Jumper for boot configuration
• X SAMTEC QSH series, 240 way connector to connect mini module to motherboard
UM2661
SPC58XXADPT100S features
2.2 Hardware dimension and PCB component view
The mini module has the following dimension:
• 127 mm x 114.3 mm (PCB dimension)
• Max top components height 19 mm
• PCB thickness: 1.6 mm
• Max bottom components height 3.5 mm
UM2661 - Rev 1
page 4/23
Hardware dimension and PCB component view
Figure 3. SPC58XXADPT100S top component view
UM2661
UM2661 - Rev 1
page 5/23
Figure 4. SPC58XXADPT100S bottom component view
UM2661
Pin numbering for jumpers
2.3 Pin numbering for jumpers
Close to selection jumper (both 3-pin and 4-pin), are shown in silkscreen the indications of connections.
See below some examples.
Figure 5. Selection jumper scheme
UM2661 - Rev 1
page 6/23
3 Hardware and jumper settings
3.1 Power supplies
When the mini module is plugged into the motherboard, power is supplied directly by the motherboard. In this
setup, the external power supply input available on the mini module should NOT be used.
When the SPC58XXADPT100S mini module is used as a stand-alone board, external power supplies must be
used (5 V, 3.3 V, 1.25 V).
The following jumpers are used to configure the power supply:
Table 1. Supply related jumpers
Jumper Description Default
J2 Jumper to enable the use of Supply 3.3V_SR Closed
J3 Jumper to enable the use of Supply 5.0V_SR Closed
J4 Jumper to enable the use of Supply 1.25V_SR Closed
VDD_HV_ADR voltage configuration:
• 1-2 5.0V_LR
J5
• 2-3 3.3V_SR
• 2-4 5.0V_SR
VDD_HV_ADV voltage configuration:
• 1-2 5.0V_LR
J6
• 2-3 3.3V_SR
• 2-4 5.0V_SR
VDD_HV_IO_MAIN voltage configuration:
J9
• 1-2 5.0V_SR
• 2-3 3.3V_SR
VDD_LV voltage configuration:
J11
• 1-2 1.25V_SR
• 2-3 1.25V from Ballast circuit
Supply for BALLAST circuit configuration:
J12
• 1-2 VDD_HV_IO_MAIN
• 2-3 5.0V_SR
VDD_HV_FLA voltage configuration, connect or disconnect VDD_HV_FLA from
JP1
VDD_HV_IO_MAIN
UM2661
Hardware and jumper settings
1-2 (5.0V_LR)
1-2 (5.0V_LR)
1-2 (5.0V_SR)
1-2 (1.25V_SR)
1-2 (VDD_HV_IO_MAIN)
Closed
(Connect VDD_HV_FLA to
VDD_HV_IO_MAIN)
UM2661 - Rev 1
page 7/23
Loading...