Datasheet LD29300P2T15R, LD29300D2T18R, LD29300D2M18R, LD29300P2T18R, LD29300P2M18R Datasheet (ST)

...
3 A, very low drop voltage regulators
Features
Very low dropout voltage (Typ. 0.4 at 3 A)
Guaranteed output current up to 3 A
Fixed voltage with ± 1 % tolerance at 25 °C
Logic controlled electronic shutdown available
in PPAK
Description
The LD29300xx is a high current, high accuracy, low-dropout voltage regulator series. These regulators feature 400 mV dropout voltage and very low ground current. Designed for high current loads, these devices are also used in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. Typical applications are in power supply switching post regulation, Series power supply for monitors, Series power supply for VCRs and TVs, Computer systems and Battery powered systems.
TO-220
2
P
PAK /A P2PAK
LD29300xx
D2PAK
D2PAK/A

Table 1. Device summary

Part numbers Output voltages
LD29300XX15 1.5 V
LD29300XX18 1.8 V
LD29300XX25 2.5 V
LD29300XX33 3.3 V
LD29300XX50 5.0 V
LD29300XX80 8.0 V
LD29300XX ADJ
July 2008 Rev 12 1/26
www.st.com
26
Contents LD29300xx
Contents
1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2/26
LD29300xx Diagram

1 Diagram

Figure 1. Schematic diagram for adjustable version

Figure 2. Schematic diagram for fixed version

* Only for version with inhibit function.
3/26
Pin configuration LD29300xx

2 Pin configuration

Figure 3. Pin connections (top view)

TO-220
P2PAK
* Not connected for fixed version.
P2PAK/A
D2PAK
2
D
PAK/A
4/26
LD29300xx Typical application

3 Typical application

Figure 4. Application circuit

* Only for version with inhibit function.
VO = V
(1 + R1/R2)
REF
5/26
Maximum ratings LD29300xx

4 Maximum ratings

Table 2. Absolute maximum ratings

Symbol Parameter Value Unit
V
I
I
O
P
D
T
STG
T
OP
1. Above 14 V the device is automatically in shut-down.
DC input voltage 30
Output current Internally limited mA
Power dissipation Internally limited mW
Storage temperature range -55 to 150 °C
Operating junction temperature range -40 to 125 °C
Note: Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied.

Table 3. Thermal data

Symbol Parameter TO-220 D2PA K- P2PAK-D2PAK/A-P2PA K/ A Un it
(1)
V
R
R
Thermal resistance junction-ambient 50 60 °C/W
thJA
Thermal resistance junction-case 3 3 °C/W
thJC
6/26
LD29300xx Electrical characteristics

5 Electrical characteristics

Table 4. Electrical characteristics of LD29300#15
(I
= 10 mA, TJ = 25 °C, VI = 3.5 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
Minimum operating input
V
I
voltage
Output voltage
V
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 3 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
I
Quiescent current
q
Short circuit current VI - VO = 5.5V 4.5 A
I
sc
Control input logic low OFF MODE
V
IL
V
Control input logic high ON MODE
IH
I
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design
= 10mA to 3A, TJ = -40 to 125°C 2.5 V
I
O
= 10mA to 3A, VI = 3 to 7V
I
O
= -40 to 125°C
T
J
= 3.5 ± 1V, IO = 1.5A
I
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
V
= 13V, V
I
= 10Hz to 100kHz, IO = 100mA 60 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
1.485 1.5 1.515
1.47 1.53
(2)
65 75 dB
mA
V
RMS
7/26
Electrical characteristics LD29300xx
Table 5. Electrical characteristics of LD29300#18
(I
= 10 mA, TJ = 25 °C, VI = 3.8 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
= 10mA to 3A, VI = 3 to 7.3V
I
V
Output voltage
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 3 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
V
I
Dropout voltage
DROP
I
Quiescent current
q
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design.
3. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99 % of its nominal value with + 1 V applied to VI.
V
O
O
= -40 to 125°C
T
J
= 3.8 ±1V, IO = 1.5A
I
I
= 500mA, TJ = -40 to 125°C
O
= 1.5A, TJ = -40 to 125°C
O
= 3A, TJ = -40 to 125°C
I
O
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 60 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
(3)
(3)
(3)
1.782 1.8 1.818
1.764 1.836
(2)
62 72 dB
0.1
0.2
0.4 0.7
mA
V
VI
RMS
8/26
LD29300xx Electrical characteristics
Table 6. Electrical characteristics of LD29300#25
(I
= 10 mA, TJ = 25 °C, VI = 4.5 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
= 10mA to 3A, VI = 3.5 to 8V
I
V
Output voltage
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 3 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
V
I
Dropout voltage
DROP
I
Quiescent current
q
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design.
3. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99 % of its nominal value with + 1 V applied to VI.
V
O
O
= -40 to 125°C
T
J
= 4.5 ±1V, IO = 1.5A
I
I
= 500mA, TJ = -40 to 125°C
O
= 1.5A, TJ = -40 to 125°C
O
= 3A, TJ = -40 to 125°C
I
O
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 100 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
(3)
(3)
(3)
2.475 2.5 2.525
2.45 2.55
(2)
55 70 dB
0.1
0.2
0.4 0.7
mA
V
VI
RMS
9/26
Electrical characteristics LD29300xx
Table 7. Electrical characteristics of LD29300#33
(I
= 10 mA, TJ = 25 °C, VI = 5.3 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
= 10mA to 3A, VI = 4.3 to 8.8V
I
V
Output voltage
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 4.3 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
V
I
Dropout voltage
DROP
I
Quiescent current
q
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design.
3. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99 % of its nominal value with + 1 V applied to VI.
V
O
O
= -40 to 125°C
T
J
= 5.3 ±1V, IO = 1.5A
I
I
= 500mA, TJ = -40 to 125°C
O
= 1.5A, TJ = -40 to 125°C
O
= 3A, TJ = -40 to 125°C
I
O
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 132 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
(3)
(3)
(3)
3.267 3.3 3.333
3.234 3.366
(2)
52 67 dB
0.1
0.2
0.4 0.7
mA
V
VI
RMS
10/26
LD29300xx Electrical characteristics
Table 8. Electrical characteristics of LD29300#50
(I
= 10 mA, TJ = 25 °C, VI = 7 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
= 10mA to 3A, VI = 6 to 10.5V
I
V
Output voltage
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 6 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
V
I
Dropout voltage
DROP
I
Quiescent current
q
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design.
3. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99 % of its nominal value with + 1 V applied to VI.
V
O
O
= -40 to 125°C
T
J
= 7 ±1V, IO = 1.5A
I
I
= 500mA, TJ = -40 to 125°C
O
= 1.5A, TJ = -40 to 125°C
O
= 3A, TJ = -40 to 125°C
I
O
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 200 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
(2)
(3)
(3)
(3)
4.95 5 5.05
4.9 5.1
49 64 dB
0.1
0.2
0.4 0.7
mA
V
VI
RMS
11/26
Electrical characteristics LD29300xx
Table 9. Electrical characteristics of LD29300#80
= 10 mA, TJ = 25 °C, VI = 10 V, V
(I
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF, unless otherwise
specified)
Symbol Parameter Test conditions Min. Typ. Max. Unit
= 10mA to 3A, VI = 9 to 13V
I
V
Output voltage
O
ΔV
ΔV
Load regulation IO = 10mA to 3A 0.2 1.0 %
O
Line regulation VI = 9 to 13V 0.06 0.5 %
O
SVR Supply voltage rejection f = 120 Hz, V
V
I
Dropout voltage
DROP
I
Quiescent current
q
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Guaranteed by design.
3. Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99 % of its nominal value with + 1 V applied to VI.
V
O
O
= -40 to 125°C
T
J
= 9 ±1V, IO = 1.5A
I
I
= 500mA, TJ = -40 to 125°C
O
= 1.5A, TJ = -40 to 125°C
O
= 3A, TJ = -40 to 125°C
I
O
I
= 1.5A, TJ = -40 to 125°C 20 50
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 320 µV
P
= GND, TJ = -40 to 125°C 130 180 µA
INH
(1)
, TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
(2)
(3)
(3)
(3)
7.92 8 8.08
7.84 8.16
45 59 dB
0.1
0.2
0.4 0.7
mA
V
VI
RMS
12/26
LD29300xx Electrical characteristics
Table 10. Electrical characteristics of LD29300#ADJ
(I
= 10 mA, TJ = 25 °C, VI = 3.23 V, V
O
INH
= 2 V
(1)
, CI = 330 nF, CO = 10 µF adjust pin tied to
output pin)
Symbol Parameter Test conditions Min. Typ. Max. Unit
Minimum operating input
V
I
voltage
ΔVOLoad regulation IO = 10mA to 3A 0.2 1.0 %
ΔV
V
Line regulation VI = 2.5 V to 13V 0.06 0.5 %
O
Reference voltage
REF
SVR Supply voltage rejection f = 120 Hz, V
I
Quiescent current
q
I
I
Adjust pin current TJ = -40 to 125°C
ADJ
I
Short circuit current VI - VO = 5.5V 4.5 A
sc
Control input logic low OFF MODE
V
IL
Control input logic high ON MODE
V
IH
Control input current TJ = -40 to 125°C, V
INH
eN Output noise voltage B
1. Only for version with Inhibit function.
2. Reference voltage is measured between output and GND pin, with ADJ PIN tied to V
3. Guaranteed by design.
I
= 10mA to 3A, TJ = -40 to 125°C 2.5 V
O
= 10mA to 3A, VI = 2.5 to 4.5V
I
O
= -40 to 125°C
T
J
= 1.5A, TJ = -40 to 125°C 20 50
I
O
= 3A, TJ = -40 to 125°C 45 100
I
O
= 13V, V
V
I
= 10Hz to 100kHz, IO = 100mA 50 µV
P
(2)
= 3.23 ±1V, IO = 1.5A
I
= GND, TJ = -40 to 125°C 130 180 µA
INH
(3)
(1)
,TJ = -40 to 125°C 0.8 V
(1)
, TJ = -40 to 125°C 2 V
= 13V 5 10 µA
INH
-1% 1.23 +1%
-2% +2%
(3)
65 75 dB
.
OUT
A
mA
V
RMS
13/26
Typical characteristics LD29300xx

6 Typical characteristics

Figure 5. Output voltage vs temperature Figure 6. Dropout voltage vs temperature
Figure 7. Dropout voltage vs output current Figure 8. Quiescent current vs output current
Figure 9. Quiescent current vs output current Figure 10. Quiescent current vs supply
14/26
voltage
LD29300xx Typical characteristics

Figure 11. Quiescent current vs temperature Figure 12. Quiescent current vs temperature

Figure 13. Short circuit current vs temperature Figure 14. Supply voltage rejection vs
temperature
Figure 15. Stability vs C
O

Figure 16. Line transient

VI=3.5 to 5.5V, I
=10mA, VO=2.5V, CO=10µF
LOAD
15/26
Typical characteristics LD29300xx

Figure 17. Load transient

VI=4.5V, IO=10mA to 3A, VO=2.5V, CO=47µF
16/26
LD29300xx Package mechanical data

7 Package mechanical data

In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
17/26
Package mechanical data LD29300xx
TO-220 (A type) mechanical data
Dim.
A 4.40 4.60 0.173 0.181
b 0.61 0.88 0.024 0.035
b1 1.15 1.70 0.045 0.067
c0.49 0.70 0.019 0.028
D 15.25 15.75 0.600 0.620
E 10.0 10.40 0.394 0.409
e 2.4 2.7 0.094 0.106
e1 4.95 5.15 0.195 0.203
F1.23 1.32 0.048 0.052
H1 6.2 6.6 0.244 0.260
J1 2.40 2.72 0.094 0.107
L13.0 14.0 0.512 0.551
L1 3.5 3.93 0.138 0.155
L20 16.4 0.646
L3028.9 1.138
φP 3.75 3.85 0.148 0.152
Q 2.65 2.95 0.104 0.116
Min. Typ. Max. Min. Typ. Max.
mm. inch.
18/26
0015988/N
LD29300xx Package mechanical data
D2PAK mechanical data
mm. inch.
Dim.
Min. Typ. Max. Min. Typ. Max.
A 4.4 4.6 0.173 0.181
A1 2.49 2.69 0.098 0.106
A2 0.03 0.23 0.001 0.009
B 0.7 0.93 0.027 0.036
B2 1.14 1.7 0.044 0.067
C 0.45 0.6 0.017 0.023
C2 1.23 1.36 0.048 0.053
D 8.95 9.350.352 0.368
D1 8 0.315
E 10 10.4 0.393 0.409
E1 8.5 0.335
G4.88 5.28 0.192 0.208
L 15 15.85 0.590 0.624
L2 1.27 1.4 0.050 0.055
L3 1.4 1.75 0.055 0.068
M2.4 3.2 0.094 0.126
R 0.4 0.016
V2 8°0°
P011P6G
19/26
Package mechanical data LD29300xx
D2PAK/A mechanical data
mm. inch.
Dim.
Min. Typ. Max. Min. Typ. Max.
A 4.40 4.60 0.173 0.181
A1 2.49 2.69 0.098 0.106
A2 0.03 0.23 0.001 0.009
B 0.7 0.93 0.028 0.037
B1 0.8 1.3 0.031 0.051
B2 1.14 1.7 0.045 0.067
C 0.45 0.60 0.018 0.024
C2 1.23 1.36 0.048 0.054
D 8.95 9.350.352 0.368
D1 8 0.315
E 10 10.4 0.394 0.409
E1 8.5 0.335
G4.88 5.28 0.192 0.208
L 15 15.85 0.591 0.624
L2 1.27 1.4 0.050 0.055
M2.4 3.2 0.094 0.126
R 0.4 0.016
V2 8°0°
20/26
7106164/D
LD29300xx Package mechanical data
P2PAK mechanical data
Dim.
Min. Typ. Max. Min. Typ. Max.
A4.304.80 0.169 0.188
A1 2.40 2.80 0.094 0.110
A2 0.03 0.23 0.001 0.009
b 0.80 1.05 0.031 0.041
c 0.45 0.60 0.017 0.023
c2 1.17 1.37 0.046 0.053
D 8.95 9.350.352 0.368
D2 8 0.315
E 10.00 10.40 0.393 0.409
E1 8.5 0.334 0.409
e 3.20 3.60 0.126 0.142
e1 6.60 7.00 0.260 0.275
L13.70 14.50 0.539 0.571
L2 1.25 1.40 0.049 0.055
L3 0.90 1.70 0.035 0.067
L5 1.55 2.40 0.061 0.094
R 0.40 0.016
V2 8°0°
mm. inch.
7226255/B
21/26
Package mechanical data LD29300xx
P2PAK/A mechanical data
Dim.
Min. Typ. Max. Min. Typ. Max.
A4.304.80 0.169 0.188
A2 0.03 0.23 0.001 0.009
C 1.17 1.37 0.046 0.053
D 2.40 2.800.094 0.110
D1 8.95 9.350.352 0.368
E 0.45 0.60 0.017 0.023
F0.80 1.05 0.031 0.041
G 3.20 3.60 0.126 0.142
G1 6.60 7.00 0.260 0.275
H1 8.5 0.334 0.409
H2 10.00 10.40 0.393 0.409
L 15 15.85 0.590 0.624
L1 8 0.315
L2 1.27 1.40 0.050 0.055
M2.4 3.2 0.094 0.126
R 0.40 0.016
V2 8°0°
mm. inch.
22/26
7157127/A
LD29300xx Package mechanical data
Tape & reel D2PAK-P2PAK-D2PAK/A-P2PAK/A mechanical data
Dim.
Min. Typ. Max. Min. Typ. Max.
A180 7.086
C 12.8 13.0 13.2 0.504 0.512 0.519
D 20.2 0.795
N60 2.362
T 14.4 0.567
Ao 10.50 10.6 10.70 0.413 0.417 0.421
Bo 15.70 15.80 15.90 0.618 0.622 0.626
Ko 4.804.90 5.00 0.189 0.193 0.197
Po 3.9 4.0 4.1 0.153 0.157 0.161
P 11.9 12.0 12.1 0.468 0.472 0.476
mm. inch.
23/26
Order codes LD29300xx

8 Order codes

Table 11. Order codes

Packages
TO-220 D
LD29300V33 LD29300D2M33R LD29300P2T33R LD29300P2M33R 3.3 V
LD29300V50 LD29300D2T50R
1. Available on request
2
PA K D2PAK /A P2PA K
LD29300P2T15R 1.5 V
LD29300D2T18R LD29300D2M18R LD29300P2T18R LD29300P2M18R 1.8 V
LD29300D2M25R 2.5 V
(1)
LD29300D2M50R LD29300P2T50R LD29300P2M50R 5.0 V
LD29300P2T80R 8.0 V
LD29300P2TR LD29300P2MTR
(1)
P2PA K/ A
(1)
Output
voltage
ADJ
24/26
LD29300xx Revision history

9 Revision history

Table 12. Document revision history

Date Revision Changes
21-Oct-2005 7 Order codes updated.
10-Apr-2007 8 Order codes updated.
11-May-2007 9 Order codes updated.
08-Jun-2007 10 Order codes updated.
03-Apr-2008 11 Modified: Table 11 on page 24.
11-Jul-2008 12 Modified: Table 11 on page 24.
25/26
LD29300xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
26/26
Loading...