based on the L6563 and STW55NM60N
Features
■ Single range input voltage from 185 V to 265 V,
50/60 Hz
■ Output voltage: 400 V ±5%
■ Inductor saturation protection
■ Optimized EMC input filter (in accordance with
EN55014 and EN55022)
■ Power factor > 0.98
■ Efficiency > 95%
■ THD (total harmonic distortion) below 10%
starting from 1 kW
■ RoHS compliant
STEVAL-ISF001V1
3 kW fixed off-time PFC
Data brief
STEVAL-ISF001V1
Description
The STEVAL-ISF001V1 demonstration board
provides a compact and ready-to-use solution for
the implementation of a simple PFC (power factor
correction) system capable of supplying loads
with a power close to the maximum delivered in
most typical domestic applications.
For this power range, the use of continuous mode
PFC operation becomes mandatory in order to
drain a current with an RMS value not exceeding
the maximum allowed by the metering system,
and to minimize the size of components involved
in system operation.
Normally, the use of a standard continuous mode
driver chip requires a more expensive and
complex driver, as well as associated passive
components. However, STMicroelectronics’
patented solution allows the use of a simple
driver, designed for transition mode operation, in
fixed off-time, variable frequency, PWM
modulation.
This type of modulation provides a current on the
PFC boost inductor comparable to that of
traditional continuous mode modulation.
November 2009 Doc ID 16769 Rev 1 1/4
For further information contact your local STMicroelectronics sales office.
www.st.com
4
Schematic diagram STEVAL-ISF001V1
1 Schematic diagram
Figure 1. STEVAL-ISF001V1 schematic diagram
2/4 Doc ID 16769 Rev 1
AM01975v1
STEVAL-ISF001V1 Revision history
2 Revision history
Table 1. Document revision history
Date Revision Changes
11-Nov-2009 1 Initial release.
Doc ID 16769 Rev 1 3/4
STEVAL-ISF001V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
STMicroelectronics group of companies
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4 Doc ID 16769 Rev 1
Loading...