STEVAL-ISA102V1
80 W high performance transition mode PFC demonstration board
Data brief
Features
■ Line voltage range: 88 to 265 VAC
■ Minimum line frequency (f
■ Regulated output voltage: 400 V
■ Rated output power: 80 W
■ Maximum 2f
■ Hold-up time: 20 ms (V
output voltage ripple: 10 V pk-pk
L
300 V)
■ Minimum switching frequency: 35 kHz
■ Minimum estimated efficiency: 92%
(V
= 90 VAC, P
IN
■ Maximum ambient temperature: 50 °C
■ PCB type and size: single-side, 35 µm, CEM-1,
OUT
108 x 57 mm
■ RoHS compliant
): 47 Hz
L
DROP
= 80 W)
after hold-up time:
Description
The L6562A is a current-mode PFC controller
operating in transition mode (TM). With the same
pinout as its L6562 predecessor, the L6562A
offers improved performance mainly in terms of
efficiency and noise immunity.
The STEVAL-ISA102V1 implements an 80 W,
wide-range mains input and a PFC
pre-conditioner suitable for ballast, adapters, flat
screen displays, etc.
February 2012 Doc ID 022845 Rev 1 1/4
For further information contact your local STMicroelectronics sales office.
www.st.com
4
Circuit schematic STEVAL-ISA102V1
270 k
Ω
1N4148
100
Ω
270 k
Ω
022 F
270
k
Ω
1N4148
100
Ω
270
k
Ω
0
22
F
1 Circuit schematic
Figure 1. Circuit schematic
C6
450V
Po=80W
Vo=400V
NTC
2.5 Ω
D1
STTH1L06
T1
R14
Ω
Ω
R11
1M
R12
1M
Ω
R50 - 22 k
C3 - 2200 nF
R6
47 kΩ
47 µF
Q1
R7
33 Ω
GD
7
C23
150 nF
21
5
L6562A
ZCD COMP INV
8
3
STP8NM50FP
R8
47k Ω
R15
4
CS
6
GND
SHORTED
R13B
R13
R10
R9
0.68 Ω
0.68 Ω
82 kΩ
15 kΩ
0.25W
0.25W
C5
D8
D2
1N5248B
R5
R4
R1
1 MΩ
C1
2/4 Doc ID 022845 Rev 1
P1
µ
.
630V
W08
+
F1
VCC
R2
4A/250V
C4
C2
C29
10nF
R3
100 nF
25V
22 µF
Ω
15 k
E25x13x7 core, N67 ferrite
1.5 mm gap for 0.7 mH primary inductance
Primary: 102 turns 20x0.1 mm
Secondary: 10 turns 0.1 mm
Boost Inductor Spec (ITACOIL E2543/E)
AM11916v1
MULT
1 MΩ
-
to
Vac
88V
264V
STEVAL-ISA102V1 Revision history
2 Revision history
Table 1. Document revision history
Date Revision Changes
21-Feb-2012 1 Initial release.
Doc ID 022845 Rev 1 3/4
STEVAL-ISA102V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
STMicroelectronics group of companies
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4 Doc ID 022845 Rev 1
Loading...