ST IDZ301V1 User Manual

Download

Features

Demonstration board for the SPZB32W1 series

of IEEE 802.15.4 ZigBee

STEVAL-IDZ301V1 STEVAL-IDZ302V1

radio communication modules

Data brief

■ Integrated RF module belonging to the

SPZB32W1 series of IEEE 802.15.4 ZigBee

modules

■ 20-pin JTAG connector for programming and

debugging purposes

■ Hardware support for application development:

– Temperature sensor – Circuitry for measuring the battery voltage – Two configurable push buttons – Two configurable LEDs

■ Mini-USB connector and USB-RS-232 bridge

■ Reset push button allows DC power source

selection between the external power supply or external USB supply

■ LED power indicator

■ Jumper for boot activation

■ Jumpers for serial communication setup

(RS232 or mini-USB)

■ 24-pin, double-row header for access to the

remaining STM32W GPIO signals and interfaces

■ The kit contains a software library including

utilities and application samples

STEVAL-IDZ30xV1

the packages available from the ST website for ZigBee PRO, Zigbee RF4CE and simplified MAC of the STM32W108 microcontroller family.

Table 1. Device summary

Order code Module

STEVAL-IDZ301V1 SPZB32W1A2

STEVAL-IDZ302V1 SPZB32W1C2

Description

The STEVAL-IDZ30xV1 is a demonstration board of the SPZB32W1 series of IEEE 802.15.4 ZigBee STM32W108CU6 microcontroller that integrates a 32-bit ARM a 2.4 GHz, IEEE 802.15.4 radio.

The STEVAL-IDZ30xV1 kit allows testing the performance of the RF, the features of the protocol libraries defined for the microcontroller, and prototyping the target application. The kit includes a development board and a software library that can be integrated in the structure of

September 2011 Doc ID 022056 Rev 1 1/6

For further information contact your local STMicroelectronics sales office.

RF modules based on the

Cortex™ - M3 microprocessor and

www.st.com

Block diagram, schematic and main components STEVAL-IDZ301V1, STEVAL-IDZ302V1

1 Block diagram, schematic and main components

1.1 Block diagram

Figure 1. Steval-IDZ30xV1 HW block diagram

STLM75

2/6 Doc ID 022056 Rev 1

STEVAL-IDZ301V1, STEVAL-IDZ302V1 Block diagram, schematic and main components

1.2 Schematic

Figure 2. STEVAL-IDZ30xV1 schematic

Doc ID 022056 Rev 1 3/6

Block diagram, schematic and main components STEVAL-IDZ301V1, STEVAL-IDZ302V1

1.3 Main components

Figure 3. STEVAL-IDZ30xV1 - main components

STLM75

Reset

Conf. Leds

Boot Jmp

IMD9A

Power Jack

Power JMP

MiniUSB

Power Led

Conf. buttons

RS232/USB Bridge

Serial JMP

24 pin Exp. Connector

SPZB32W1xx.0

JTAG Connector

AM09230V1

4/6 Doc ID 022056 Rev 1

STEVAL-IDZ301V1, STEVAL-IDZ302V1 Revision history

2 Revision history

Table 2. Document revision history

Date Revision Changes

23-Sep-2011 1 Initial release.

Doc ID 022056 Rev 1 5/6

STEVAL-IDZ301V1, STEVAL-IDZ302V1

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America