
Demonstration board for 2x1 W differential input stereo audio
Features
STEVAL-CCA008V1
amplifier based on the TS4998
Data Brief
■ Operating range from V
■ 1 W output power per channel
@V
=5 V,THD+N =1%, RL =8 Ω
CC
■ Ultra low standby consumption:10 nA typ.
■ 80 dB PSRR @ 217 Hz with grounded inputs
■ High SNR: 106 dB(A) typ.
■ Fast startup time: 45 ms typ.
■ Circuit free of Pop and click
■ Dedicated standby pin per channel
■ Lead-free QFN16 4x4mm package
= 2.7 V to 5.5 V
CC
Description
The demonstration board STEVAL-CCA008V1 is
made to evaluate the TS4998 that is designed for
top-class stereo audio applications. Thanks to its
compact and power-dissipation efficient QFN16
package with exposed pad, it suits a variety of
applications. With a BTL configuration, this audio
power amplifier is capable of delivering 1 W per
channel of continuous RMS output power into an
8 Ω load at 5 V.
STEVAL-CCA008V1
Each output channel (left and right) also has its
own external controlled standby mode pin to
reduce the supply current to less than 10 nA per
channel. The device also features an internal
thermal shutdown protection. The gain of each
channel can be configured by external gain
setting resistors.
February 2009 Rev 1 1/4
For further information contact your local STMicroelectronics sales office.
www.st.com
4

Circuit schematic STEVAL-CCA008V1
1 Circuit schematic
Figure 1. Schematic
VCC
JP1
JP2
Cn1
Cn2
Cn3
Cn4
Cin1
330nF
Cin2
330nF
Cin3
330nF
Cin4
330nF
4
3
2
1
4
3
2
1
R1
24k
R2
24k
R3
24k
R4
24k
TS4998 - QFN16
TS4998
1
LI N-
2
LI N+
4
RIN-
3
RIN+
14
Bypass
1uF
Cb
LEFT
RIGHT
BIASSTBY
GND GND
6
5
Cn8
13
Vcc
12
STBYR
7
VCC
LOUT -
11
LOUT +
9
ROUT-
10
ROUT+
U1
1
2
3
Cn9
-
+
-
+
STBYL
8
VCC
1
2
3
Cs1
1uF
Cs2
100nF
Cn5
Cn6
Cn7
2/4

STEVAL-CCA008V1 Revision history
2 Revision history
Table 1. Document revision history
Date Revision Changes
09-Feb-2009 1 Initial release.
3/4

STEVAL-CCA008V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, an
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4