AN3094
Application note
EVAL2293Q demonstration board
Introduction
This application note describes the EVAL2293Q demonstration board for the L2293Q pushpull four channel driver with integrated diodes. The L2293Q is designed to drive inductive loads such as DC and stepping motors, or relays and solenoids. The board implements a typical application which can be used as a reference design to drive two-phase bipolar stepper motors with currents up to 0.6 A DC, multiple DC motors and a wide range of inductive loads.
Housed in a QFN 5 x 5 mm 32-lead package, the small footprint of the L2293Q makes the PCB very compact (24.5 x 24.5 mm).
!-V
May 2010 |
Doc ID 16540 Rev 1 |
1/8 |
www.st.com
Demonstration board description |
AN3094 |
|
|
63 |
/54 |
/54 |
633 |
). |
|
|
). |
%.!",% |
|
|
%.!",% |
). |
|
|
). |
|
/54 |
/54 |
|
!-V
Table 1. |
EVAL2293Q: pin description |
||
Name |
|
Type |
Function |
|
|
|
|
VS |
|
Power |
Supply voltage for the power output stages |
|
supply |
||
|
|
|
|
|
|
|
|
GND |
|
Ground |
Power ground terminal |
|
|
|
|
VSS |
|
Power |
Supply voltage for the logic blocks. It is connected to VS through the closed jumper JP1 |
|
supply |
||
|
|
|
|
|
|
|
|
GNDS |
|
Ground |
Signal ground terminal |
|
|
|
|
IN1 |
|
Logic input |
Bridge 1 logic input 1 |
|
|
|
|
IN2 |
|
Logic input |
Bridge 1 logic input 2 |
|
|
|
|
EN1 |
|
Logic input |
Bridge 1 enable (active high). When LOW, switches off the output 1 and 2 power transistors |
|
|
|
|
IN3 |
|
Logic input |
Bridge 2 logic input 1 |
|
|
|
|
IN4 |
|
Logic input |
Bridge 2 logic input 2 |
|
|
|
|
EN2 |
|
Logic input |
Bridge 2 enable (active high). When LOW, switches off the output 3 and 4 power transistors |
|
|
|
|
OUT1 |
|
Output |
Output 1 |
|
|
|
|
OUT2 |
|
Output |
Output 2 |
|
|
|
|
OUT3 |
|
Output |
Output 3 |
|
|
|
|
OUT4 |
|
Output |
Output 4 |
|
|
|
|
2/8 |
Doc ID 16540 Rev 1 |
AN3094 |
|
|
|
Demonstration board description |
|||||
|
|
|
|
|
|
|
|
|
|
|
Figure 3. |
EVAL2293Q demonstration board pin location |
|||||||
|
|
|
|
|
|
|
|
||
|
|
). |
%. ). 633 *0 '.$3 '.$ 63 |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
/54 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|||||
|
|
|
|
|
/54 |
||||
|
|
|
|
/54
/54
). ). %.
!-V
The logic and power voltage supply pins are connected through jumper JP1 (normally closed). If VS and VSS need to be supplied with different voltage values, JP1 should be opened and the supply to each should be provided separately through external terminals.
The INx input pins drive the corresponding half-bridge. When a low logic level is applied, the low side power switch is turned on, whereas a high logic level turns on the high side switch.
Pins EN1 and EN2 are used to disable the bridges and put the output pins in a high impedance status. The output stages integrate freewheeling diodes.
Table 2 below summarizes the electrical specifications of the application, Figure 3 shows the electrical schematic and Table 3 provides the component list.
Table 2. |
EVAL2293Q: electrical specification (recommended values) |
||
|
Parameter |
|
Value |
|
|
|
|
|
Supply voltage range (VS) |
|
VSS to 36 V |
|
|
|
|
Logic supply voltage range (VSS) |
|
2.8 (1) to 36 V |
|
RMS output current rating (OUTx) |
|
Up to 0.6 A |
|
|
|
|
|
|
Switching frequency |
|
Up to 50 kHz |
|
|
|
|
|
Input and enable voltage range |
|
0 to +5 V |
|
|
|
|
|
Operating temperature range |
|
-20 (1) to +125 °C |
L2293Q thermal resistance junction-to-ambient |
|
42 °C/W |
|
|
|
|
|
1. Please refer to the L2293Q datasheet for additional details |
|
Doc ID 16540 Rev 1 |
3/8 |